scholarly journals Experimental Evaluation of Balance Prediction Models for Sit-to-Stand Movement in the Sagittal Plane

2013 ◽  
Vol 2013 ◽  
pp. 1-9
Author(s):  
Oscar David Pena Cabra ◽  
Takashi Watanabe

Evaluation of balance control ability would become important in the rehabilitation training. In this paper, in order to make clear usefulness and limitation of a traditional simple inverted pendulum model in balance prediction in sit-to-stand movements, the traditional simple model was compared to an inertia (rotational radius) variable inverted pendulum model including multiple-joint influence in the balance predictions. The predictions were tested upon experimentation with six healthy subjects. The evaluation showed that the multiple-joint influence model is more accurate in predicting balance under demanding sit-to-stand conditions. On the other hand, the evaluation also showed that the traditionally used simple inverted pendulum model is still reliable in predicting balance during sit-to-stand movement under non-demanding (normal) condition. Especially, the simple model was shown to be effective for sit-to-stand movements with low center of mass velocity at the seat-off. Moreover, almost all trajectories under the normal condition seemed to follow the same control strategy, in which the subjects used extra energy than the minimum one necessary for standing up. This suggests that the safety considerations come first than the energy efficiency considerations during a sit to stand, since the most energy efficient trajectory is close to the backward fall boundary.

2015 ◽  
Vol 77 (20) ◽  
Author(s):  
Muhammad Fahmi Miskon ◽  
Mohd Zaki Ghazali ◽  
Mohd Bazli Bahar ◽  
Chew Xiao Lin ◽  
Fariz Ali

Sit to stand (STS) is a very challenging motion for any humanoid robotic system. In humanoid robotics field, the STS motion on the sagittal plane can be predicted using three-link robot inverse kinematic and dynamic model. However, a three-link model is complicated and requires high computational resource to compute. Hence, in this paper a much simpler model namely telescopic inverted pendulum is proposed. The objective of this project is to model and validate sit to stand motion of humanoid robot using telescopic inverted pendulum model. In order to validate the model, simulated joint torques using both three-link and TIPS model are compared using MATLAB software. Result shows that there is a linear relationship between Telescopic Inverted Pendulum with the 3 Link model thus, it is feasible to use TIPS to represent STS motion of a three-link multi-segment robot.


1996 ◽  
Vol 12 (2) ◽  
pp. 173-184 ◽  
Author(s):  
Brian L. Davis ◽  
Mark D. Grabiner

Measurement of postural sway is a valuable research and clinical tool that can provide information related to various central and peripheral elements of the nervous system. The present study involved modeling single-limb standing as an inverted pendulum tethered to a supporting surface by two sets of springs that simulated the stiffness of muscles spanning the joint and the inherent stiffness of the joint itself. There are four key elements of this model: (a) joint stiffness is greater in the frontal plane compared to the sagittal plane (neither being affected by fatigue), (b) muscle stiffness is exponentially related to its extension from a resting position, (c) muscle stiffness is reduced by fatigue, and (d) an "ankle strategy" is used to maintain upright single-limb posture. It is concluded that an inverted pendulum model can be used to adequately predict sway frequencies and amplitudes in the mediolateral (ML) and anteroposterior (AP) directions for single-limb stance pre- and postfatigue. In particular, it is possible for acute muscle fatigue to increase sway in the ML direction but not necessarily in the AP direction.


1999 ◽  
Vol 354 (1385) ◽  
pp. 869-875 ◽  
Author(s):  
E. Otten

The balance of standing humans is usually explained by the inverted pendulum model. The subject invokes a horizontal ground–reaction force in this model and controls it by changing the location of the centre of pressure under the foot or feet. In experiments I showed that humans are able to stand on a ridge of only a few millimetres wide on one foot for a few minutes. In the present paper I investigate whether the inverted pendulum model is able to explain this achievement. I found that the centre of mass of the subjects sways beyond the surface of support, rendering the inverted pendulum model inadequate. Using inverse simulations of the dynamics of the human body, I found that hip–joint moments of the stance leg are used to vary the horizontal component of the ground–reaction force. This force brings the centre of mass back over the surface of support. The subjects generate moments of force at the hip–joint of the swing leg, at the shoulder–joints and at the neck. These moments work in conjunction with a hip strategy of the stance leg to limit the angular acceleration of the head–arm–trunk complex. The synchrony of the variation in moments suggests that subjects use a motor programme rather than long latency reflexes.


2018 ◽  
Vol 8 (8) ◽  
pp. 1257 ◽  
Author(s):  
Tianqi Yang ◽  
Weimin Zhang ◽  
Xuechao Chen ◽  
Zhangguo Yu ◽  
Libo Meng ◽  
...  

The most important feature of this paper is to transform the complex motion of robot turning into a simple translational motion, thus simplifying the dynamic model. Compared with the method that generates a center of mass (COM) trajectory directly by the inverted pendulum model, this method is more precise. The non-inertial reference is introduced in the turning walk. This method can translate the turning walk into a straight-line walk when the inertial forces act on the robot. The dynamics of the robot model, called linear inverted pendulum (LIP), are changed and improved dynamics are derived to make them apply to the turning walk model. Then, we expend the new LIP model and control the zero moment point (ZMP) to guarantee the stability of the unstable parts of this model in order to generate a stable COM trajectory. We present simulation results for the improved LIP dynamics and verify the stability of the robot turning.


Sign in / Sign up

Export Citation Format

Share Document