Implantation of Novel Small-Diameter Polyurethane Vascular Prostheses Interposed in Canine Femoral and Carotid Arteries

2004 ◽  
Vol 36 (4) ◽  
pp. 241-248 ◽  
Author(s):  
K. Karapınar ◽  
A.T. Ulus ◽  
U. Tütün ◽  
A. Aksöyek ◽  
N. Apaydın ◽  
...  
1992 ◽  
Vol 15 (10) ◽  
pp. 579-584 ◽  
Author(s):  
L.J. Brossollet

Despite intensive research, the success of artificial small-diameter vascular grafts has yet to match that of natural grafts like the saphenous vein. One of the possible reasons is mechanical mismatch of the graft to the host vessel. The study of compliance (dilatability under pressure) has not been conclusive, especially after a series of recent investigations on vein graft evolution. Lately, the focus has been shifting towards more detailed characteristics, like anastomic behaviour, longitudinal elasticity, and flow-related variables. When the relevant property is identified, it should be included in the criteria for design and use of vascular prostheses.


Vascular ◽  
2019 ◽  
Vol 27 (6) ◽  
pp. 636-647 ◽  
Author(s):  
Rahim Faturechi ◽  
Ata Hashemi ◽  
Nabiollah Abolfathi ◽  
Atefeh Solouk ◽  
Alexander Seifalian

Objective Compliance and viscoelastic mismatches of small diameter vascular conduits and host arteries have been the cause of conduit’s failure. Methods To reduce these mismatches, the aim of this study was to develop and characterize a polyurethane conduit, which mimics the viscoelastic behaviors of human arteries. Electrospinning technique was used to fabricate tubular polyurethane conduits with similar properties of the human common carotid artery. This was achieved by manipulating the fiber diameter by altering the syringe flow rate of the solution. The mechanical and viscoelastic properties of the fabricated electrospun polyurethane conduits were, then, compared with commercially available vascular conduits, expanded polytetrafluoroethylene, polyethylene terephthalate (Dacron®) and the healthy human common carotid arteries. In addition, a comprehensive constitutive model was proposed to capture the visco-hyperelastic behavior of the synthetic electrospun polyurethanes, commercial conduits and human common carotid arteries. Results Results showed that increasing the fiber diameter of electrospun polyurethanes from 114 to 190 nm reduced Young’s modulus from 8 to 2 MPa. Also, thicker fiber diameter yielded in higher conduits’ viscosity. Furthermore, the results revealed that proposed visco-hyperelastic model is strongly able to fit the experimental data with great precision which proofs the reliability of the proposed model to address both nonlinear elasticity and viscoelasticity of the electrospun polyurethanes, commercial conduits and human common carotid arteries. Conclusions In conclusion, statistical analysis revealed that the elastic and viscous properties of 190 nm fiber diameter conduit are very similar to that of human common carotid artery in comparison to the commercial expanded polytetrafluoroethylene and Dacron® that are up to nine and seven times stiffer than natural vessels. Therefore, based on our findings, from the mechanical point of view, by considering the amount of Young’s modulus, compliance, distensibility and viscoelastic behavior, the fabricated electrospun polyurethane with fiber diameter of 189.6 ± 52.89 nm is an optimum conduit with promising potential for substituting natural human vessels.


2003 ◽  
Vol 111 (5) ◽  
pp. 415-427 ◽  
Author(s):  
Y.J.T van der Zijpp ◽  
A.A. Poot ◽  
J. Feijen

2013 ◽  
Vol 843 ◽  
pp. 66-69 ◽  
Author(s):  
Hui Jing Zhao ◽  
Guo Li Zhou ◽  
Zhi Qing Yuan

Biomaterials used for vascular prostheses should possess certain strength that can keep the normal blood fluidity, as well as certain flexibility and elasticity that can resist blood pulsation pressure. In order to fabricate small diameter vascular prostheses (SDVP) that possess matchable mechanical properties with natural blood vessels, a bi-layered tubular structure composed of electrospinning blended nanofiber and silk fiber was designed and prepared in this study. The inner layer of the structure, prepared through electrospinning, was composed of Poly (L-lactide-co-ε-caprolactone) (PLCL) and silk fibroin (SF) blended nanofibers. Braided silk tube was used as the outer layer of the structure. Morphological, structural and mechanical properties including peak stress, peak strain, and Youngs modulus of the prototype bi-layered SDVP were characterized initially. Results showed that the diameter range of the blended nanofiber was between 100 and 900 nm, and the fiber diameter increased with the content increase of PLCL. Through blending PLCL together with SF, peak stress and peak strain of the electrospun inner layer were improved, and that of the Youngs modulus decreased. Meanwhile, the outer layer of SDVP was stronger and had higher Youngs modulus. Those mechanical performances of the prototype bi-layered SDVP fabricated in this study are similar to natural blood vessels, which provide a promising biomaterial that could be applied on tubular tissue engineering scaffolds.


1991 ◽  
Vol 8 (1-2) ◽  
pp. 81-88 ◽  
Author(s):  
G. Soldani ◽  
M. Steiner ◽  
P.M. Galletti ◽  
L. Lelli ◽  
M. Palla ◽  
...  

1988 ◽  
Vol 22 (S14) ◽  
pp. 245-256 ◽  
Author(s):  
R. R. Kowligi ◽  
W. W. von Maltzahn ◽  
R. C. Eberhart

2020 ◽  
Vol 12 (6) ◽  
pp. 6
Author(s):  
L.V. Antonova ◽  
E.O. Krivkina ◽  
M.A. Rezvova ◽  
V.V. Sevostyanova ◽  
V.O. Tkachenko ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document