scholarly journals Trajectory optimization of the 6-degrees-of-freedom high-speed parallel robot based on B-spline curve

2019 ◽  
Vol 103 (1) ◽  
pp. 003685041988011
Author(s):  
Jiangping Mei ◽  
Fan Zhang ◽  
Jiawei Zang ◽  
Yanqin Zhao ◽  
Han Yan
Keyword(s):  
Trajectory Optimization ◽  
High Speed ◽  
Degrees Of Freedom ◽  
Control Point ◽  
Parallel Robot ◽  
B Spline ◽  
Spline Curve ◽  
Deformation Problem ◽  
Point Subset ◽  
6 Degrees Of Freedom

According to the problem that the existing high-speed parallel robot cannot satisfy the operation requirements of non-planar industrial production line, a 6-degrees-of-freedom high-speed parallel robot is proposed to carry out the kinematic and dynamic analyses. Combining with the door-type trajectory commonly used by the parallel robot, it adopts 3-, 5-, and 7-time B-spline curve motion law to conduct the trajectory planning in operation space. Taking the average cumulative effect of joint jerky as the optimization target, a trajectory optimization method is proposed to improve the smoothness of robot end-effector motion with the selected motion law. Furthermore, to solve the deformation problem of the horizontal motion stage of the trajectory, a mapping model between the control point subset of B-spline and the motion point subset of trajectory is established. Based on the main diagonally dominant characteristic of the coefficient matrix, the trajectory deformation evaluation index is constructed to optimize the smoothness and minimum deformation of the robot motion trajectory. Finally, compared to without the optimization, the maximum robot joint jerk decreases by 69.4% and 72.3%, respectively, and the maximum torque decreases by 51.4% and 38.9%, respectively, under a suitable trajectory deformation.

scholarly journals Trajectory Optimization Algorithm for a 4-DOF Redundant Parallel Robot Based on 12-Phase Sine Jerk Motion Profile

Actuators ◽  
2021 ◽  
Vol 10 (4) ◽  
pp. 80
Author(s):  
Shengqiao Hu ◽  
Huimin Kang ◽  
Hao Tang ◽  
Zhengjie Cui ◽  
Zhicheng Liu ◽  
...  
Keyword(s):  
Energy Consumption ◽  
Trajectory Optimization ◽  
High Speed ◽  
Degrees Of Freedom ◽  
Sudden Change ◽  
Parallel Robot ◽  
Joint Space ◽  
Allowable Limit ◽  
Three Phase ◽  
Motion Profile

To improve high motion accuracy and efficiency in the high-speed operation of a 4-DOF (4 degrees of freedom) redundant parallel robot, this paper introduces a trajectory planning of the parallel robot in joint space based on the twelve-phase sine jerk motion profile. The 12-phase sine jerk motion profile utilizes the characteristics of a sine function. Furthermore, the penalty function is used to optimize the trajectory energy consumption under the constraint condition. The simulation and experimental results show that the energy consumption of joint space is slightly higher than that of the three-phase sine jerk motion profile, but the overall operation is more accurate and stable. Specifically, the sudden change of force and velocity in each joint is eliminated, which is the cause of mechanism oscillation. Moreover, the force of each joint is more average. The results indicate that each movement is closer to the maximum allowable limit and the running efficiency is higher.

Modelling and Simulation of a Isoglide T3R1 Parallel Robot

2010 ◽  
Vol 166-167 ◽  
pp. 457-462
Author(s):  
Dan Verdes ◽  
Radu Balan ◽  
Máthé Koppány
Keyword(s):  
High Speed ◽  
Degrees Of Freedom ◽  
Parallel Robot ◽  
Parallel Robots ◽  
Practical Implementation ◽  
Medical Robots ◽  
The Past ◽  
And Control ◽  
Workspace Design ◽  
Human Systems

Parallel robots find many applications in human-systems interaction, medical robots, rehabilitation, exoskeletons, to name a few. These applications are characterized by many imperatives, with robust precision and dynamic workspace computation as the two ultimate ones. This paper presents kinematic analysis, workspace, design and control to 3 degrees of freedom (DOF) parallel robots. Parallel robots have received considerable attention from both researchers and manufacturers over the past years because of their potential for high stiffness, low inertia and high speed capability. Therefore, the 3 DOF translation parallel robots provide high potential and good prospects for their practical implementation in human-systems interaction.

Dynamic Trajectory Planning for a Three Degrees-of-Freedom Cable-Driven Parallel Robot Using Quintic B-Splines

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Sen Qian ◽  
Kunlong Bao ◽  
Bin Zi ◽  
W. D. Zhu
Keyword(s):  
Trajectory Planning ◽  
Degrees Of Freedom ◽  
Parallel Robot ◽  
Planning Method ◽  
End Effector ◽  
B Spline ◽  
B Splines ◽  
Pick And Place ◽  
Two Factors ◽  
Three Degrees Of Freedom

Abstract This paper presents a new trajectory planning method based on the improved quintic B-splines curves for a three degrees-of-freedom (3-DOF) cable-driven parallel robot (CDPR). First, the conditions of positive cables’ tension are expressed in terms of the position and acceleration constraints of the end-effector. Then, an improved B-spline curve is introduced, which is employed for generating a pick-and-place path by interpolating a set of given via-points. Meanwhile, by expressing the position and acceleration of the end-effector in terms of the first and second derivatives of the improved B-spline, the cable tension constraints are described in the form of B-spline parameters. According to the properties of the defined pick-and-place path, the proposed motion profile is dominated by two factors: the time taken for the end-effector to pass through all the via-points and the ratio between the nodes of B-spline. The two factors are determined through multi-objective optimization based on the efficiency coefficient method. Finally, experimental results on a 3-DOF CDPR show that the improved B-spline exhibits overall superior behavior in terms of velocity, acceleration, and cables force compared with the traditional B-spline. The validity of the proposed trajectory planning method is proved through the experiments.

DeltaBot: A New Cable-Based Ultra High Speed Robot

2003 ◽  
Author(s):  
Saeed Behzadipour ◽  
Robert Dekker ◽  
Amir Khajepour ◽  
Edmon Chan
Keyword(s):  
High Speed ◽  
Degrees Of Freedom ◽  
Manufacturing Industry ◽  
Design Procedure ◽  
Parallel Manipulators ◽  
Parallel Robot ◽  
Parallel Robots ◽  
Manufacturing Cost ◽  
End Effector ◽  
Serial Manipulators

The growing needs for high speed positioning devices in the automated manufacturing industry have been challenged by robotic science for more than two decades. Parallel manipulators have been widely used for this purpose due to their advantage of lower moving inertia over the conventional serial manipulators. Cable actuated parallel robots were introduced in 1980’s to reduce the moving inertia even further. In this work, a new cable-based parallel robot is introduced. For this robot, the cables are used not only to actuate the end-effector but also to apply the necessary kinematic constraints to provide three pure translational degrees of freedom. In order to maintain tension in the cables, a passive air cylinder is used to push the end-effector against the stationary platform. In addition to low moving inertia, the new design benefits from simplicity and low manufacturing cost by eliminating joints from the robot’s mechanism. The design procedure and the results of experiments will be discussed in the following.

scholarly journals Tolerance Design and Kinematic Calibration of a Four-Degrees-of-Freedom Pick-and-Place Parallel Robot

2016 ◽  
Vol 8 (6) ◽  
Author(s):  
Tian Huang ◽  
Pujun Bai ◽  
Jiangping Mei ◽  
Derek G. Chetwynd
Keyword(s):  
High Speed ◽  
Degrees Of Freedom ◽  
Parallel Robot ◽  
Simplified Model ◽  
Tolerance Design ◽  
Kinematic Calibration ◽  
Distance Measurements ◽  
End Effector ◽  
Pick And Place ◽  
Source Errors

This paper presents a comprehensive methodology for ensuring the geometric pose accuracy of a 4DOF high-speed pick-and-place parallel robot having an articulated traveling plate. The process is implemented by four steps: (1) formulation of the error model containing all possible geometric source errors; (2) tolerance design of the source errors affecting the uncompensatable pose accuracy via sensitivity analysis; (3) identification of the source errors affecting the compensatable pose accuracy via a simplified model and distance measurements; and (4) development of a linearized error compensator for real-time implementation. Experimental results show that a tilt angular accuracy of 0.1/100 and a volumetric/rotational accuracy of 0.5 mm/±0.8 deg of the end-effector can be achieved over the cylindrical task workspace.

scholarly journals Control point adjustment for B-spline curve approximation

2004 ◽  
Vol 36 (7) ◽  
pp. 639-652 ◽  
Author(s):  
Huaiping Yang ◽  
Wenping Wang ◽  
Jiaguang Sun
Keyword(s):  
Control Point ◽  
B Spline ◽  
Spline Curve ◽  
Curve Approximation
Sign in / Sign up

Export Citation Format

Share Document