scholarly journals Finite element and biomechanical analysis of risk factors for implant failure during tension band plating

2020 ◽  
Vol 48 (11) ◽  
pp. 030006052097207
Author(s):  
Jing Ding ◽  
Fei Wang ◽  
Fangchun Jin ◽  
Zhen-kai Wu ◽  
Pin-quan Shen
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Finite Element Model ◽  
Three Dimensional ◽  
Biomechanical Model ◽  
Element Model ◽  
Tension Band ◽  
Biomechanical Analysis ◽  
Implant Failure ◽  
Element Analysis

Objective Tension band plating has recently gained widespread acceptance as a method of correcting angular limb deformities in skeletally immature patients. We examined the role of biomechanics in procedural failure and devised a new method of reducing the rate of implant failure. Methods In the biomechanical model, afterload (static or cyclic) was applied to each specimen. The residual stress of the screw combined with different screw sizes and configurations were measured and compared by X-ray diffraction. With regard to static load and similar conditions, the stress distribution was analyzed according to a three-dimensional finite element model. Results The residual stress was close to zero in the static tension group, whereas it was very high in the cyclic load group. The residual stress of screws was significantly lower in the convergent group and parallel group than in the divergent group. The finite element model showed similar results. Conclusions In both the finite element analysis and biomechanical tests, the maximum stress of the screw was concentrated at the position where the screws enter the cortex. Cyclic loading is the primary cause of implant failure.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

INVESTIGATION OF DAMAGE ON DERBENDIKHAN DAM DURING EARTHQUAKE EXCITATION

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Cagri Mollamahmutoglu ◽  
Idris Bedirhanoglu
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Three Dimensional ◽  
Element Model ◽  
Main Body ◽  
Damage Development ◽  
Element Analysis ◽  
Rock Fill ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

In this study, the performance of a damaged dam was evaluated through a three-dimensional finite element model. The dam is located in Derbendikhan city of Northern Iraq and damaged during a 7.3 magnitude earthquake which was happened 30 kilometers south of Halabja city. Derbendikhan dam which was built between the years 1956-1961 is a clay-core rock fill dam. The damage of the dam was investigated at the site right after the earthquake and some cracks were observed in the main body of the dam. The main goal of this work is to present the results of the survey which was conducted at the site and investigating the damage development mechanism through a realistic three-dimensional finite element model of the dam. As complying with the observations at the site, the finite element analysis has shown that the primary failure mechanism is due to the separation of the core and rock fill sections at the downstream side of the dam.

Three Dimensional Finite Element Analysis of a Split-Sleeve Cold Expansion Process

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
S. Ismonov ◽  
S. R. Daniewicz ◽  
J. C. Newman ◽  
M. R. Hill ◽  
M. R. Urban
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Residual Stress Field ◽  
Expansion Process ◽  
Element Analysis ◽  
Cold Expansion ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

A cold expansion process is used to prolong the fatigue life of a structure under cyclic loadings. The process produces a beneficial compressive residual stress zone in the hole vicinity, which retards the initiation and propagation of the crack at the hole edge. In this study, a three-dimensional finite element model of the split-sleeve cold expansion process was developed to predict the resulting residual stress field. A thin rectangular aluminum sheet with a centrally located hole was considered. A rigid mandrel and an elastic steel split sleeve were explicitly modeled with the appropriate contact elements at the interfaces between the mandrel, the sleeve, and the hole. Geometrical and material nonlinearities were included. The simulation results were compared with experimental measurements of the residual stress. The influence of friction and the prescribed boundary conditions for the sheet were studied. Differences between the split-sleeve- and the non-split-sleeve model solutions are discussed.

3D Finite Element Analysis of Prestressed Cutting

2012 ◽  
Vol 591-593 ◽  
pp. 766-770 ◽  
Author(s):  
Rui Tao Peng ◽  
Fang Lu ◽  
Xin Zi Tang ◽  
Yuan Qiang Tan
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Bearing Steel ◽  
Arbitrary Lagrangian Eulerian ◽  
Machined Surface ◽  
Element Analysis ◽  
Simulation Techniques ◽  
Ale Formulation

In order to reveal the adjustment principle of prestressed cutting on the residual stress of hardened bearing steel GCr15, a three-dimensional thermal elastic-viscoplastic finite element model was developed using an Arbitrary Lagrangian Eulerian (ALE) formulation. Several key simulation techniques including the material constitutive model, constitutive damage law and contact with friction were discussed, simulation of chip formation during prestressed cutting was successfully conducted. At the prestresses of 0 MPa, 341 MPa and 568 MPa, distributions of residual stress on machined surface were simulated and experimentally verified. The results indicated that residual compressive stress on machined surface were achieved and actively adjusted by utilizing the prestressed cutting method; meanwhile, within the elastic limit of bearing steel material, the higher applied prestress leads to the more prominent compressive residual stress in the surface layer and subsequently the higher fatigue resistance of the part.

Establishment and validation of finite element model of ossification of cervical posterior longitudinal ligament with intervertebral fusion

2020 ◽  
Author(s):  
Li Hui ◽  
Liu Huiqing ◽  
Zhang Yaning
Keyword(s):  
Finite Element ◽  
Cervical Spine ◽  
Finite Element Model ◽  
Three Dimensional ◽  
Element Model ◽  
Posterior Longitudinal Ligament ◽  
Intervertebral Discs ◽  
Biomechanical Analysis ◽  
Intervertebral Fusion ◽  
Dimensional Finite Element

Abstract [Background ]: To establish a three-dimensional finite element model of ossification of the posterior longitudinal ligament of the cervical spine with intervertebral fusion and verify its effectiveness, and provide a platform for finite element calculation and biomechanical analysis in the later stage.[Method]: Select the Department of Spinal Surgery, Linfen People's Hospital A volunteer imported 719 DICOM format images of cervical spine CT scans into Mimics modeling software to build a preliminary 3D model in the stl format, and used Geomagic Studio 2013 software to refine and refine the 3D model to smooth out noise and generate NURBS surfaces The model was then imported into the finite element analysis software Ansys workbench 15.0, adding ligaments and intervertebral discs, meshing, assigning material properties, and simulating 6 activities of the human cervical spine, and comparing them with references.[Results]: A total of 7 Cervical vertebral body, 1 thoracic vertebral body, 5 intervertebral discs and ligaments, etc., with a total of 320512 nodes and 180905 units. It has a realistic appearance, high degree of detail reduction, and ossification of the cervical longitudinal longitudinal ligament with good geometric similarity Incorporate a three-dimensional finite element model of intervertebral fusion. In flexion and extension, left and right lateral flexion, and axial rotation activity compared with references, there is not much difference.[Conclusion]: OPLL merger interbody fusion dimensional finite element model has good mechanical and geometric similarity after similarity cervical established in this study, the model can provide a platform for the latter to further biomechanical analysis.

Precision Machines: Diagnostics of Vibration Through Modal and Finite Element Analysis

1991 ◽  
Author(s):  
V. Prakash ◽  
R. J. Montague
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Three Dimensional ◽  
Element Model ◽  
Test Model ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Structure Correlation ◽  
Three Dimensional Finite Element ◽  
Precision Machines

Abstract This paper presents the diagnostics of the effects of vibration on the precise placement of electronic components in a surface mount assembly process. Experimental Modal Analysis using present day software/hardware as well as a three dimensional finite element model are performed on the machine structure. Correlation between the experiment and finite element model are also performed and the strength of using the finite element model as a test model for contemplating any design alterations are presented.

Parametric Analysis Mechanical Properties of Bolted Joints

2010 ◽  
Vol 97-101 ◽  
pp. 3924-3927 ◽  
Author(s):  
Da Zhao Yu ◽  
Yue Liang Chen ◽  
Zhong Hu Jia ◽  
Yong Gao ◽  
Wen Lin Liu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Three Dimensional ◽  
Element Model ◽  
Bolted Joints ◽  
Bolted Joint ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

Three-dimensional finite element model of a bolted joint has been developed in the non-linear finite element code MSC.Marc and attempts were made to validate it by comparing results with those of experiments and other finite element. Issues in modeling the contact between the joint parts, which affect the accuracy and efficiency of the model, were presented. Experimental measurements of surface strains and load transfer ratio(LTR) were compared with results from finite element analysis. The results show that three-dimensional finite element model of bolted joint can produce results in close agreement with experiment. Three-dimensional effects such as bolt titling, seconding and through-thickness variations in stress and strain are well represented by such models. Three-dimensional finite element analysis was also used to study the effects of different parameters on the mechanical behaviour of single lap bolted joints. The results show that straight hole, small bolt diameter, and big hole pitch are selected first for bolted joint if other conditions allowed, and effect of bolt material on LTR of joint is small for small load. Interference and pre-stress should be strictly controlled for bolted joints in order to attain the best fatigue capability of lap joint.

scholarly journals Establishment of a Finite Element Model and Biomechanical Analysis of Different Fixation Methods for Total Talar Prosthesis Replacement

2021 ◽  
Author(s):  
Qian dong Yang ◽  
Le Chang ◽  
Xuting Bian ◽  
Lin Ma ◽  
Tao Xu ◽  
...  
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Screw Fixation ◽  
Articular Surface ◽  
Three Dimensional ◽  
Element Model ◽  
Element Analysis ◽  
Ankle Motion ◽  
Fixation Methods ◽  
Without Screws

Abstract Back ground：A three-dimensional finite element model of the whole foot with high geometric similarity was established and used to simulate the conditions after whole talar prosthesis implantation with several fixation methods, including Screw fixation of subtalar+talus-navicular joint, fixation with screws at only the subtalar joint, and fixation without screws. The biomechanical characteristics of the talus prosthesis were assessed in different gait phases to guide the selection of surgical methods in clinical practice.Methods：With the three-dimensional CT data of a volunteer's foot, Mimics13.0 and Geomagic10.0 software were used to carry out geometric reconstruction of the ankle-related tissues, and Hypermesh10.0 software was used for grid division and material attribute selection. Finally, the data were imported into Abaqus 6.9, and the simulated screw data were applied to different models. Finite element models with different fixation methods were simulated, and the stresses exerted by the human body in three gait phases (heel-strike, midstance and push-off) were simulated. The pressure changes in the articular surface around the talus or the prosthesis, the micromotion of the talus and the prosthesis and ankle motion were measured. Results：Finite element analysis on the biomechanical mechanism showed that screw fixation of the prosthesis in different gait phases mainly increases the pressure on the tibialis articular surface as well as decreases the pressure on the fused articular surface and joint micromotion, which hinders ankle motion. The indicator values were nearly the same in the models of fixation without screws and the normal state.Conclusion：The 3D finite element model created in this study has been verified to be an accurate and reliable model. The biomechanical mechanism varies by fixation method according to finite element analysis. Fixation of the prosthesis without screws yields values most similar to normal values.

Sign in / Sign up

Export Citation Format

Share Document