Parameter optimization and texture evolution in single point incremental sheet forming process

2019 ◽  
Vol 234 (1-2) ◽  
pp. 126-139 ◽  
Author(s):  
Shamik Basak ◽  
K Sajun Prasad ◽  
Amarjeet Mehto ◽  
Joy Bagchi ◽  
Y Shiva Ganesh ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Regression Models ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Single Point Incremental Forming ◽  
Input Process ◽  
Truncated Cone

Prototyping through incremental sheet forming is emerging as a latest trend in the manufacturing industries for fabricating personalized components according to customer requirement. In this study, a laboratory scale single-point incremental forming test setup was designed and fabricated to deform AA6061 sheet metal plastically. In addition, response surface methodology with Box–Behnken design technique was used to establish different regression models correlating input process parameters with mechanical responses such as angle of failure, part depth per unit time and surface roughness. Correspondingly, the regression models were implemented to optimize the input process parameters, and the predicted responses were successfully validated at the optimal conditions. It was observed that the predicted absolute error for angle of failure, part depth per unit time and surface roughness responses was approximately 0.9%, 4.4% and 6.3%, respectively, for the optimum parametric combination. Furthermore, the post-deformation responses from an optimized single point incremental forming truncated cone were correlated with microstructural evolution. It was observed that the peak hardness and highest areal surface roughness of 158 ± 9 HV and 1.943 μm, respectively, were found near to the pole of single-point incremental forming truncated cone, and the highest major plastic strain at this region was 0.80. During incremental forming, a significant increase in microhardness occurred due to grain refinement, whereas a substantial increase in the Brass and S texture component was responsible for the increase in the surface roughness.

Multiobjective optimization of process variables in single-point incremental forming using grey relational analysis coupled with entropy weights

2021 ◽  
pp. 146442072110204
Author(s):  
Abdulmajeed Dabwan ◽  
Adham E Ragab ◽  
Mohamed A Saleh ◽  
Atef M Ghaleb ◽  
Mohamed Z Ramadan ◽  
...  
Keyword(s):  
Grey Relational Analysis ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Numerical Control ◽  
Single Point Incremental Forming ◽  
Process Variables ◽  
Relational Analysis ◽  
Grey Relational

Incremental sheet forming is a specific group of sheet forming methods that enable the manufacture of complex parts utilizing computer numerical control instead of specialized tools. It is an incredibly adaptable operation that involves minimal usage of sophisticated tools, dies, and forming presses. Besides its main application in the field of rapid prototyping, incremental sheet forming processes can be used for the manufacture of unique parts in small batches. The goal of this study is to broaden the knowledge of the deformation process in single-point incremental forming. This work studies the deformation behavior in single-point incremental forming by experimentally investigating the principal stresses, principal strains, and thinning of single-point incremental forming products. Conical-shaped components are fabricated using AA1050-H14 aluminum alloy at various combinations of fundamental variables. The factorial design is employed to plan the experimental study and analysis of variance is conducted to analyze the results. The grey relational analysis approach coupled with entropy weights is also implemented to identify optimum process variables for single-point incremental forming. The results show that the tool diameter has the greatest effect on the thinning of the SPIF product, followed by the sheet thickness, step size, and feed rate.

Forces in Single Point and Two Point Incremental Forming

2005 ◽  
Vol 6-8 ◽  
pp. 449-456 ◽  
Author(s):  
J. Jeswiet ◽  
Joost R. Duflou ◽  
Alexander Szekeres
Keyword(s):  
Sheet Metal ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Single Point Incremental Forming

Forces have been measured in Two Point Incremental Forming and Single Point Incremental Forming of Sheet Metal. It is necessary to know the magnitude of these forces when trying to determine if the equipment available is capable of Forming Sheet Metal by either one of the two foregoing processes. The magnitude of forces is also needed when developing appropriate models for the Incremental Sheet Forming. The forces measured in forming cones and truncated pyramids from AA 3003-0 are described.

The Effected of Single Point Incremental Forming Process Parameters on the Formed Part Surface Roughness

2014 ◽  
Vol 979 ◽  
pp. 335-338
Author(s):  
Kittiphat Rattanachan ◽  
Chatchapol Chungchoo
Keyword(s):  
Surface Roughness ◽  
Sheet Metal ◽  
Process Parameters ◽  
Feed Rate ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Tool Rotational Speed ◽  
Forming Process ◽  
Inner Surface

The single point incremental forming process (SPIF) are suited for sheet metal prototyping, because it is a low cost production process that produces sheet metal part without any used of die, and easy to adjust the part’s geometry by change toolpath. But the quality of forming parts is still in doubt. In some applications, such as mould cavity for rapid mould and the medical parts, in this case the inside surface roughness plays an importance role. In this paper, the SPIF process parameters that affected to the inner surface roughness were experimental studied. The investigated parameters are composing of tool feed rate, side overlap, depth step and tool radius. The 2k-p factorial experimental design was used to analyze the interaction between each parameter. The results showed that increasing feed rate and depth step decreased inner surface roughness. Reducing tool rotational speed and feed rate reduced inner surface roughness. So increasing depth step with decreasing side overlap reduced inner surface roughness. The large tool radius and lower side overlap improved inner surface roughness. The large tool radius and higher depth step improved inner surface roughness. And last, reducing tool rotational speed with larger tool radius, the inner surface roughness is decreased.

scholarly journals Design and manufacturing of a fixing device for incremental sheet forming process

2018 ◽  
Vol 178 ◽  
pp. 02004 ◽  
Author(s):  
Daniel Nasulea ◽  
Gheorghe Oancea
Keyword(s):  
Sheet Metal ◽  
Deep Drawing ◽  
Incremental Forming ◽  
Single Point ◽  
Fem Simulation ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Design And Manufacturing

In incremental sheet forming processes, the expensive dedicated tool are avoided and replaced with a cheap and simple fixing device which support the sheet metal blanks. The current paper presents how a fixing device used for single point incremental forming device is designed, FEM simulated and manufactured. The fixing device can be used for parts with a cone frustum and pyramidal frustum made of DC05 deep drawing steel. The forces developed in the process and the device displacements were estimated using FEM simulation. The device components were manufactured using a CNC machines and the physical assembly is also presented in the paper.

Single Point Incremental Forming of a Medical Implant

2013 ◽  
Vol 554-557 ◽  
pp. 1388-1393 ◽  
Author(s):  
Rogério Araújo ◽  
Pedro Teixeira ◽  
M. Beatriz Silva ◽  
Ana Reis ◽  
Paulo Martins
Keyword(s):  
Plastic Deformation ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Potential Fields ◽  
Single Point Incremental Forming ◽  
Medical Implants ◽  
Medical Implant ◽  
Product Customization

Single point incremental forming (SPIF) belongs to the branch of incremental sheet forming processes that enables plastic deformation of blanks without resorting to any specific die or punch. The main characteristics of SPIF determine its appropriateness for producing small batches or single products, being the medical implants one of the key potential fields of application, due to the need of product customization to each patient. Customization is particularly important for obtaining preoperative implants because it allows a significant decrease in the overall surgery time in conjunction with a higher level of flexibility to ensure the required shapes. This results in an improved final product either in aesthetic as well as in functional terms.

scholarly journals Study of Friction and Wear Effects in Aluminum Parts Manufactured via Single Point Incremental Forming Process Using Petroleum and Vegetable Oil-Based Lubricants

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3973
Author(s):  
José M. Diabb Zavala ◽  
Oscar Martínez-Romero ◽  
Alex Elías-Zúñiga ◽  
Héctor Manuel Leija Gutiérrez ◽  
Alejandro Estrada-de la Vega ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Friction And Wear ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Step Size ◽  
Vertical Step ◽  
Stribeck Curves

This paper focuses on studying how mineral oil, sunflower, soybean, and corn lubricants influence friction and wear effects during the manufacturing of aluminum parts via the single point incremental forming (SPIF) process. To identify how friction, surface roughness, and wear change during the SPIF of aluminum parts, Stribeck curves were plotted as a function of the SPIF process parameters such as vertical step size, wall angle, and tool tip semi-spherical diameter. Furthermore, lubricant effects on the surface of the formed parts are examined by energy dispersive spectroscopy (EDS) and scanning electron microscope (SEM) images, the Alicona optical 3D measurement system, and Fourier-transform infrared spectroscopy (FTIR). Results show that during the SPIF process of the metallic specimens, soybean and corn oils attained the highest friction, along forces, roughness, and wear values. Based on the surface roughness measurements, it can be observed that soybean oil produces the worst surface roughness finish in the direction perpendicular to the tool passes (Ra =1.45 μm) considering a vertical step size of 0.25 mm with a 5 mm tool tip diameter. These findings are confirmed through plotting SPIFed Stribeck curves for the soybean and corn oils that show small hydrodynamic span regime changes for an increasing sample step-size forming process. This article elucidates the effects caused by mineral and vegetable oils on the surface of aluminum parts produced as a function of Single Point Incremental Sheet Forming process parameters.

Sign in / Sign up

Export Citation Format

Share Document