The Effected of Single Point Incremental Forming Process Parameters on the Formed Part Surface Roughness

2014 ◽  
Vol 979 ◽  
pp. 335-338
Author(s):  
Kittiphat Rattanachan ◽  
Chatchapol Chungchoo
Keyword(s):  
Surface Roughness ◽  
Sheet Metal ◽  
Process Parameters ◽  
Feed Rate ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Tool Rotational Speed ◽  
Forming Process ◽  
Inner Surface

The single point incremental forming process (SPIF) are suited for sheet metal prototyping, because it is a low cost production process that produces sheet metal part without any used of die, and easy to adjust the part’s geometry by change toolpath. But the quality of forming parts is still in doubt. In some applications, such as mould cavity for rapid mould and the medical parts, in this case the inside surface roughness plays an importance role. In this paper, the SPIF process parameters that affected to the inner surface roughness were experimental studied. The investigated parameters are composing of tool feed rate, side overlap, depth step and tool radius. The 2k-p factorial experimental design was used to analyze the interaction between each parameter. The results showed that increasing feed rate and depth step decreased inner surface roughness. Reducing tool rotational speed and feed rate reduced inner surface roughness. So increasing depth step with decreasing side overlap reduced inner surface roughness. The large tool radius and lower side overlap improved inner surface roughness. The large tool radius and higher depth step improved inner surface roughness. And last, reducing tool rotational speed with larger tool radius, the inner surface roughness is decreased.

scholarly journals Study of Friction and Wear Effects in Aluminum Parts Manufactured via Single Point Incremental Forming Process Using Petroleum and Vegetable Oil-Based Lubricants

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3973
Author(s):  
José M. Diabb Zavala ◽  
Oscar Martínez-Romero ◽  
Alex Elías-Zúñiga ◽  
Héctor Manuel Leija Gutiérrez ◽  
Alejandro Estrada-de la Vega ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Friction And Wear ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Step Size ◽  
Vertical Step ◽  
Stribeck Curves

This paper focuses on studying how mineral oil, sunflower, soybean, and corn lubricants influence friction and wear effects during the manufacturing of aluminum parts via the single point incremental forming (SPIF) process. To identify how friction, surface roughness, and wear change during the SPIF of aluminum parts, Stribeck curves were plotted as a function of the SPIF process parameters such as vertical step size, wall angle, and tool tip semi-spherical diameter. Furthermore, lubricant effects on the surface of the formed parts are examined by energy dispersive spectroscopy (EDS) and scanning electron microscope (SEM) images, the Alicona optical 3D measurement system, and Fourier-transform infrared spectroscopy (FTIR). Results show that during the SPIF process of the metallic specimens, soybean and corn oils attained the highest friction, along forces, roughness, and wear values. Based on the surface roughness measurements, it can be observed that soybean oil produces the worst surface roughness finish in the direction perpendicular to the tool passes (Ra =1.45 μm) considering a vertical step size of 0.25 mm with a 5 mm tool tip diameter. These findings are confirmed through plotting SPIFed Stribeck curves for the soybean and corn oils that show small hydrodynamic span regime changes for an increasing sample step-size forming process. This article elucidates the effects caused by mineral and vegetable oils on the surface of aluminum parts produced as a function of Single Point Incremental Sheet Forming process parameters.

scholarly journals Common defects of parts manufactured through single point incremental forming

2021 ◽  
Vol 343 ◽  
pp. 04007
Author(s):  
Mihai Popp ◽  
Gabriela Rusu ◽  
Sever-Gabriel Racz ◽  
Valentin Oleksik
Keyword(s):  
Sheet Metal ◽  
Metal Forming ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Metal Forming Process ◽  
Serial Robot ◽  
The Many ◽  
Cold Metal

Single point incremental forming is one of the most intensely researched die-less manufacturing process. This process implies the usage of a CNC equipment or a serial robot which deforms a sheet metal with the help of a relatively simple tool that follows an imposed toolpath. As every cold metal forming process, besides the many given advantages it has also some drawbacks. One big drawback in comparison with other cold metal forming processes is the low accuracy of the deformed parts. The aim of this research is to investigate the sheet metal bending mechanism through finite element method analysis. The results shows that the shape of the retaining rings has a big influence over the final geometrical accuracy of the parts manufactured through single point incremental forming.

Parameter optimization and texture evolution in single point incremental sheet forming process

2019 ◽  
Vol 234 (1-2) ◽  
pp. 126-139 ◽  
Author(s):  
Shamik Basak ◽  
K Sajun Prasad ◽  
Amarjeet Mehto ◽  
Joy Bagchi ◽  
Y Shiva Ganesh ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Regression Models ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Single Point Incremental Forming ◽  
Input Process ◽  
Truncated Cone

Prototyping through incremental sheet forming is emerging as a latest trend in the manufacturing industries for fabricating personalized components according to customer requirement. In this study, a laboratory scale single-point incremental forming test setup was designed and fabricated to deform AA6061 sheet metal plastically. In addition, response surface methodology with Box–Behnken design technique was used to establish different regression models correlating input process parameters with mechanical responses such as angle of failure, part depth per unit time and surface roughness. Correspondingly, the regression models were implemented to optimize the input process parameters, and the predicted responses were successfully validated at the optimal conditions. It was observed that the predicted absolute error for angle of failure, part depth per unit time and surface roughness responses was approximately 0.9%, 4.4% and 6.3%, respectively, for the optimum parametric combination. Furthermore, the post-deformation responses from an optimized single point incremental forming truncated cone were correlated with microstructural evolution. It was observed that the peak hardness and highest areal surface roughness of 158 ± 9 HV and 1.943 μm, respectively, were found near to the pole of single-point incremental forming truncated cone, and the highest major plastic strain at this region was 0.80. During incremental forming, a significant increase in microhardness occurred due to grain refinement, whereas a substantial increase in the Brass and S texture component was responsible for the increase in the surface roughness.

Experimental Study on Residual Formability of Single Point Incrementally Formed Part

2019 ◽  
Author(s):  
Chetan P. Nikhare
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Incremental Forming ◽  
Thickness Distribution ◽  
Single Point ◽  
Forming Limit ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Conventional Process

Abstract A substantial increase in demand on the sheet metal part usage in aerospace and automotive industries is due to the increase in the sale of these products to ease the transportation. However, due to the increase in fuel prices and further environmental regulation had left no choice but to manufacture more fuel efficient and inexpensive vehicles. These heavy demands force researchers to think outside the box. Many innovative research projects came to replace the conventional sheet metal forming of which single point incremental forming is one of them. SPIF is the emerging die-less sheet metal forming process in which the single point tool incrementally forces any single point of sheet metal at any processing time to undergo plastic deformation. It has several advantages over the conventional process like high process flexibility, elimination of die, complex shape and better formability. Previous literature provides enormous research on formability of metal during this process, process with various metals and hybrid metals, the influence of various process parameter, but residual formability after this process is untouched. Thus, the aim of this paper is to investigate the residual formability of the formed parts using single point incremental forming and then restrike with a conventional tool. The common process parameters of single point incremental forming were varied, and residual formability was studied through the conventional process. The strain and thickness distribution were measured and analyzed. In addition, the forming limit of the part was plotted and compared.

STUDY ON FORMING FORCES OF PARTS PROCESSED BY SINGLE POINT INCREMENTAL FORMING WITH DUMMY SHEET

2019 ◽  
Vol 14 (3) ◽  
Author(s):  
Vikas Sisodia ◽  
Shailendra Kumar
Keyword(s):  
Process Parameters ◽  
Feed Rate ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Thickness ◽  
Single Point Incremental Forming ◽  
Forming Force ◽  
Step Size ◽  
Wall Angle ◽  
Influence Of Process Parameters

The present paper describes the experimental investigation on influence of process parameters on maximum forming force in Single Point Incremental Forming (SPIF) process using dummy sheet. Process parameters namely dummy sheet thickness, tool size, step size, wall angle and feed rate are selected. Taguchi L18 orthogonal array is used to design the experiments. From the analysis of variance (ANOVA) dummy sheet thickness, tool size, step size and wall angle are significant process parameters while feed rate is insignificant. It is found that as dummy sheet thickness, tool size, step size and wall angle increase magnitude of peak forming force increases while there is marginal decrease in forming force as feed rate increases. Predictive model is also developed for forming force. Validation tests are performed in order to check the accuracy of developed model. Optimum set of process parameters is also determined to minimize forming force. Experimental results are in good agreement with results predicted by the developed mathematical model.

Drilled Hole Technique for Created Single Point Incremental Forming Limited Diagram

2015 ◽  
Vol 658 ◽  
pp. 177-181
Author(s):  
Kittiphat Rattanachan
Keyword(s):  
Sheet Metal ◽  
Incremental Forming ◽  
Single Point ◽  
Material Behavior ◽  
304 Stainless Steel ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Steel Blank ◽  
Etching Technique ◽  
Drilling Hole

To produce the forming limited diagram for predicting and studying material behavior in sheet metal forming, grid etching or grid marking on blank surface are applied before forming. But in single point incremental forming process, sheet metal blanks are subjected to highly strain or highly deformation which the conventional gridding is no longer to be occurred on the surface of formed part. And some material such as titanium, nickel based alloy etc are difficulty to etch the grid marks on its surface. So this paper is proposed the drilling hole technique to substitute with the grid etching technique in single point incremental forming process. The holes 2 mm. diameter were drilled on the SUS 304 stainless steel blank before forming. The deformed holes are calculated as true major strain and true minor strain and plot into a forming limited diagram. The results are compared with the conventional etching techniques which show an according trend. The drilling hole technique could be used in study the material behavior in single point incremental forming, it a low cost convenient and easy than grid etching technique.

scholarly journals Tool Path Design of the Counter Single Point Incremental Forming Process to Decrease Shape Error

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4719
Author(s):  
Kyu-Seok Jung ◽  
Jae-Hyeong Yu ◽  
Wan-Jin Chung ◽  
Chang-Whan Lee
Keyword(s):  
Sheet Metal ◽  
Tool Path ◽  
Incremental Forming ◽  
Single Point ◽  
Optimization Method ◽  
Single Point Incremental Forming ◽  
Shape Error ◽  
Forming Process ◽  
Two Stage ◽  
Shape Errors

Incremental sheet metal forming can manufacture various sheet metal products without a dedicated punch and die set. In this study, we developed a two-stage incremental forming process to decrease shape errors in the conventional incremental forming process. The forming process was classified into the first single point incremental forming (1st SPIF) process for forming a product and the counter single point incremental forming (counter SPIF) process to decrease shape error. The counter SPIF gives bending deformation in the opposite direction. Furthermore, the counter SPIF compensates for shape errors, such as section deflection, skirt spring-back, final forming height, and round. The tool path of the counter SPIF has been optimized through a relatively simple optimization method by modifying the tool path of the previous step. The tool path of the 1st SPIF depends on the geometry of the product. An experiment was performed to form a circular cup shape to verify the proposed tool path of the 1st and counter SPIF. The result confirmed that the shape error decreased when compared to the conventional SPIF. For the application, the ship-hull geometry was adopted. Experimental results demonstrated the feasibility of the two-stage incremental forming process.

The Effect of Lubricants and Material Properties in Surface Roughness and Formability for Single Point Incremental Forming Process

2014 ◽  
Vol 979 ◽  
pp. 359-362
Author(s):  
Nuttaphong Sornsuwit ◽  
Sunthorn Sittisakuljaroen
Keyword(s):  
Surface Roughness ◽  
Adhesive Wear ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Sheet Surface ◽  
Air Blowing ◽  
Asymmetric Shape ◽  
High Roughness

The single point incremental forming (SPIF) is a manufacturing process which allows small batch and asymmetric shape fabrication. The research focuses on its applications by consider surface roughness and formability. The surface roughness of specimen was resulted by the influence obtained between tool and specimen, where the lubricant played a significant role during the forming process, as well as material elongation as a mechanical property governed the formability of metal sheet. Surface roughness tester, SEM, EDS and profilometer were used for the characterizations. The results showed that low roughness value (Ra) of SUS 304 and SUS 316L obtained by applying air blowing as a lubricant, while Ti Gr2 could obtain low roughness by using MoS2. The behavior of wear was an adhesive wear which transfer to an abrasive wear. SUS 304 and SUS 316L sheet of test specimens achieved higher depth in forming by air lubricant and MoS2, and Ti Gr2 sheet revealed a better formability with MoS2. Furthermore, the highest depth was correlated with high roughness value for each material.

Sign in / Sign up

Export Citation Format

Share Document