Unsteady winglet-cavity tip on leakage flow in a high-pressure turbine stage of low-aspect ratio

2017 ◽  
Vol 232 (20) ◽  
pp. 3708-3721 ◽  
Author(s):  
Zhihua Zhou ◽  
Shaowen Chen ◽  
Songtao Wang
Keyword(s):  
High Pressure ◽  
Aspect Ratio ◽  
Flow Characteristics ◽  
Leakage Flow ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Tip Leakage ◽  
Low Aspect Ratio ◽  
Passage Vortex ◽  
Blade Tip

In an unshrouded high-pressure turbine, the upstream vane wake, vane–blade interaction and blade tip leakage flow indicate complex and unsteady flow characteristics. Considering a high-pressure turbine stage of low-aspect ratio, the effects of the flat tip, cavity tip and winglet-cavity tip on the unsteady flow characteristics are investigated by numerical simulation. The exit Mach number and Reynolds number based on the chord of vane are 0.9 and 5.5×105, respectively. The pressure ratio of stage is 2.4. The time-resolved results indicate that the winglet-cavity tip scheme has smaller time variation of the total performance parameters and obtains a smaller tip leakage mass flow and a higher turbine stage efficient than the other cases. The vane–rotor interaction affects the pressure distribution at the region of blade leading edge remarkably and leads to a large time variation of tip leakage mass flow at the front of blade tip. The unsteady aerodynamic performance is analyzed with entropy-increase distribution at stage outlet and the vane–rotor interaction is discussed by the entropy-increase phase–time and phase–phase diagrams at blade outlet. Compared with the flat tip and cavity tip, the upper passage vortex loss is reduced obviously by the winglet-cavity tip. Thus, it is evaluated that the improvement of turbine stage coefficient with winglet-cavity tip results from the reduction of the upper passage vortex loss.

Unsteady Aerodynamics of a Flat Tip and a Winglet Tip in a High-Pressure Turbine

2016 ◽  
Author(s):  
Kai Zhou ◽  
Chao Zhou
Keyword(s):  
High Pressure ◽  
Unsteady Aerodynamics ◽  
Suction Side ◽  
Leakage Flow ◽  
Turbine Stage ◽  
Tip Leakage Flow ◽  
High Pressure Turbine ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Passage Vortex

In an unshrouded high-pressure turbine, tip leakage flow results in a loss of efficiency. In this paper, the aerodynamic performance of the tip leakage flow is investigated in a turbine stage by numerical methods. A flat tip and a closed squealer tip combined with a suction side winglet are used for the rotor tips, and the two turbines are named as ‘Flat Configuration’ and ‘Winglet Configuration’. The ability of the CFD methods in predicting the unsteady flow and the tip leakage flow is validated. The steady calculations using a mixing plane between the stator and the rotor are presented first. Then, the unsteady flows of the turbine stage with a flat rotor tip and a winglet rotor tip are simulated by solving Unsteady Reynolds-Averaged Navier-Stokes (URANS) equations. Compared with the ‘Flat Configuration’, the ‘Winglet Configuration’ reduces the size of the passage vortex and the tip leakage vortex. A surprising observation is that although the ‘Winglet Configuration’ reduces the size of the tip leakage vortex, its maximum swirl strength of the tip leakage vortex is about 40% higher than that for the ‘Flat Configuration’. The steady calculation shows that the entropy generation for the turbine stage is 12.1% lower with the ‘Winglet Configuration’ than that with the ‘Flat Configuration’. The mixed-out entropy predicted in the unsteady calculation is higher than that of the steady calculation for both tips. The stator casing passage vortex has a periodic effect on the vortex near the tip gap of the rotor. The unsteady interaction of the vortices seems to be beneficial in terms of the loss. As a result, the ‘Winglet Configuration’ produces 9.4% less entropy than the ‘Flat Configuration’, which is lower than that in the case of the steady calculation.

A Novel Suction-Side Winglet Design Philosophy for High-Pressure Turbine Rotor Tips

2017 ◽  
Vol 139 (11) ◽  
Author(s):  
Chao Zhou ◽  
Fangpan Zhong
Keyword(s):  
Suction Side ◽  
Leakage Flow ◽  
The Novel ◽  
Front Part ◽  
Turbine Stage ◽  
Tip Leakage Flow ◽  
High Pressure Turbine ◽  
Tip Leakage ◽  
Design Philosophy ◽  
Passage Vortex

Winglet tips are promising candidates for future high-pressure turbine rotors. Many studies found that the design of the suction-side winglet is the key to the aerodynamic performance of a winglet tip, but there is no general agreement on the exact design philosophy. In this paper, a novel suction-side winglet design philosophy in a turbine cascade is introduced. The winglets are obtained based on the near-tip flow field of the datum tip geometry. The suction-side winglet aims to reduce the tip leakage flow particularly in the front part of the blade passage. It is found that on the casing endwall, the pressure increases in the area where the winglet is used. This reduces the tip leakage flow in the front part of the blade passage and the pitchwise pressure gradient on the endwall. As a result, the size of the tip leakage vortex reduces. A surprising observation is that the novel optimized winglet tip design eliminates the passage vortex and results in a further increasing of the efficiency. The tip leakage loss of the novel winglet tip is 18.1% lower than the datum cavity tip, with an increase of tip surface area by only 19.3%. The spanwise deflection of the winglet due to the centrifugal force is small. The tip heat load of the winglet tip is 17.5% higher than that of the cavity tip. Numerical simulation shows that in a turbine stage, this winglet tip increases the turbine stage efficiency by 0.9% mainly by eliminating the loss caused by the passage vortex at a tip gap size of 1.4% chord compared with a cavity tip.

Aerodynamic Optimization of Winglet-Cavity Tip in an Axial High Pressure Turbine Stage

2020 ◽  
Vol 37 (4) ◽  
pp. 399-411
Author(s):  
Zhihua Zhou ◽  
Shaowen Chen ◽  
Songtao Wang
Keyword(s):  
High Pressure ◽  
Suction Side ◽  
Leakage Flow ◽  
Pressure Side ◽  
Turbine Stage ◽  
Tip Leakage Flow ◽  
Aerodynamic Optimization ◽  
High Pressure Turbine ◽  
Tip Leakage ◽  
Stage Efficiency

AbstractA new geometry parametric method of winglet-cavity tip has been introduced in the optimization procedure based on three-dimensional steady CFD numerical calculation and analysis. Firstly, the reliability of numerical method and grid independency are studied. Then an aerodynamic optimization is performed in an unshrouded axial high pressure turbine with winglet-cavity tip. The optimum winglet-cavity tip has higher turbine stage efficiency and smaller tip leakage mass flow rate than the cavity tip and flat tip. Compared with the results of cavity tip, the effects of the optimum winglet-cavity tip indicate that the stage efficiency is improved effectively by 0.41% with less reduction of tip leakage mass flow rate. The variation of turbine stage efficiency with tip gap states that the optimum winglet-cavity tip obtains the smallest efficiency change rate ∆η/(∆τ/H). For the optimum winglet-cavity tip, the endwall flow and blade tip leakage flow pattern are used to analysis the physical mechanical of losses. In addition, the effects of pressure-side winglet and suction-side winglet are analyzed respectively by the deformation of the optimum winglet-cavity tip. The numerical results show that the pressure-side winglet reduces the tip leakage flow effectively, and the suction-side winglet shows a great improvement on the turbine stage efficiency.

Comparison of Turbine Tip Leakage Flow for Flat Tip and Squealer Tip Geometries at High-Speed Conditions

2004 ◽  
Vol 128 (2) ◽  
pp. 213-220 ◽  
Author(s):  
Nicole L. Key ◽  
Tony Arts
Keyword(s):  
Reynolds Number ◽  
High Speed ◽  
Flow Characteristics ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Cascade Arrangement ◽  
Oil Flow ◽  
Blade Tip ◽  
Tip Velocity

The tip leakage flow characteristics for flat and squealer turbine tip geometries are studied in the von Karman Institute Isentropic Light Piston Compression Tube facility, CT-2, at different Reynolds and Mach number conditions for a fixed value of the tip gap in a nonrotating, linear cascade arrangement. To the best knowledge of the authors, these are among the very few high-speed tip flow data for the flat tip and squealer tip geometries. Oil flow visualizations and static pressure measurements on the blade tip, blade surface, and corresponding endwall provide insight to the structure of the two different tip flows. Aerodynamic losses are measured for the different tip arrangements, also. The squealer tip provides a significant decrease in velocity through the tip gap with respect to the flat tip blade. For the flat tip, an increase in Reynolds number causes an increase in tip velocity levels, but the squealer tip is relatively insensitive to changes in Reynolds number.

The Effect of an Upstream Turbine on a Low-Aspect Ratio Vane

2004 ◽  
Author(s):  
R. J. Miller ◽  
R. W. Moss ◽  
R. W. Ainsworth ◽  
N. W. Harvey
Keyword(s):  
High Pressure ◽  
Aspect Ratio ◽  
Leading Edge ◽  
Streamwise Vortex ◽  
Relative Magnitude ◽  
Large Radius ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Interaction Mechanisms ◽  
Low Aspect Ratio

The interaction between a high-pressure rotor and a downstream vane is dominated by vortex-blade interaction. Each rotor blade passing period two co-rotating vortex pairs, the tip-leakage and upper passage vortex and the lower passage and trailing shed vortex, impinge on, and are cut by, the vane leading edge. In addition to the streamwise vortex the tipleakage flow also contains a large velocity deficit. This causes the interaction of the tip-leakage flow with a downstream vane to differ from typical vortex blade interaction. This paper investigates the effect these interaction mechanisms have on a downstream vane. The test geometry considered was a low aspect ratio second stage vane located within a S-shaped diffuser with large radius change mounted downstream of a shroudless high-pressure turbine stage. Experimental measurements were conducted at engine-representative Mach and Reynolds numbers, and data was acquired using a fastresponse aerodynamic probe upstream and downstream of the vane. Time-resolved numerical simulations were undertaken with and without a rotor tip gap in order to investigate the relative magnitude of the interaction mechanisms. The presence of the upstream stage is shown to significantly change the structure of the secondary flow in the vane and to cause a small drop in its performance.

Numerical Investigation of the Effect of Tip Leakage Flow on an Aggressive S-Shaped Intermediate Turbine Duct

2009 ◽  
Author(s):  
W. Sanz ◽  
M. Kelterer ◽  
R. Pecnik ◽  
A. Marn ◽  
E. Go¨ttlich
Keyword(s):  
High Pressure ◽  
Low Pressure ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
High Pressure Turbine ◽  
Tip Leakage ◽  
Intermediate Turbine Duct ◽  
Low Pressure Turbine ◽  
High Diffusion ◽  
Gap Height

The demand of a further increased bypass ratio of aero engines will lead to low pressure turbines with larger diameters which rotate at lower speed. Therefore, it is necessary to guide the flow leaving the high pressure turbine to the low pressure turbine at a larger diameter without any loss generating separation or flow disturbances. Due to costs and weight this intermediate turbine duct has to be as short as possible. This leads to an aggressive (high diffusion) S-shaped duct geometry. In order to investigate the influence of the blade tip gap height of a preceding rotor on such a high-diffusion duct flow a detailed measurement campaign in the Transonic Test Turbine Facility at Graz University of Technology has been performed. A high diffusion intermediate duct is arranged downstream a high-pressure turbine stage providing an exit Mach number of about 0.6 and a swirl angle of −15 degrees (counter swirl). A low-pressure vane row is located at the end of the duct and represents the counter rotating low pressure turbine at larger diameter. At the ASME 2007, results of these investigations were presented for two different tip gap heights of 1.5% span (0.8 mm) and 2.4% span (1.3 mm). In order to better understand the flow phenomena observed in the intermediate duct a detailed numerical study is conducted. The unsteady flow through the whole configuration is simulated for both gap heights as well as for a rotor with zero gap height. The unsteady data are compared at the stage exit and inside the duct to study the flow physics. The calculation of the zero gap height configuration allows to determine the influence of the tip leakage flow of the preceding rotor on the intermediate turbine duct. It turns out that for this aggressive duct the tip leakage flow has a very positive effect on the pressure recovery.

Effects of Tip Clearance on Unsteady Flow Characteristics in an Axial Turbine Stage

2009 ◽  
Author(s):  
Hao Sun ◽  
Jun Li ◽  
Zhenping Feng
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Rotor Blade ◽  
Suction Side ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Turbine Stage ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Blade Tip

The clearance between the rotor blade tip and casing wall in turbomachinery passages induces leakage flow loss and thus degrades aerodynamic performance of the machine. The flow field in turbomachinery is significantly influenced by the rotor blade tip clearance size. To investigate the effects of tip clearance size on the rotor-stator interaction, the turbine stage profile from Matsunuma’s experimental tests was adopted, and the unsteady flow fields with two tip clearance sizes of 0.67% and 2.00% of blade span was numerical simulated based on Harmonic method using NUMECA software. By comparing with the domain scaling method, the accuracy of the harmonic method was verified. The interaction mechanism between the stator wake and the leakage flow was investigated. It is found that the recirculation induced by the stator wake is separated by a significant “interaction line” from the flow field close to the suction side in the clearance region. The trend of the pressure fluctuation is contrary on both sides of the line. When the stator wakes pass by the suction side, the pressure field fluctuates and the intensity of the tip leakage flow varies. With the clearance size increasing, the “interaction line” is more far away from the suction side and the intensity of tip leakage flow also fluctuates more strongly.

The Development of Turbine Exit Flow in a Swan-Necked Inter-Stage Diffuser

2003 ◽  
Author(s):  
R. J. Miller ◽  
R. W. Moss ◽  
R. W. Ainsworth ◽  
N. W. Harvey
Keyword(s):  
High Pressure ◽  
Secondary Flow ◽  
Leakage Flow ◽  
Turbine Stage ◽  
Tip Leakage Flow ◽  
Trailing Edge ◽  
Inlet Flow ◽  
Time Resolved ◽  
Tip Leakage ◽  
Numerical Predictions

This paper describes both the migration and dissipation of flow phenomena downstream of a transonic high-pressure turbine stage. The geometry of the HP stage exit duct considered is a swan-necked diffuser similar to those likely to be used in future engine designs. The paper contains results both from an experimental programme in a turbine test facility and from numerical predictions. Experimental data was acquired using three fast-response aerodynamic probes capable of measuring Mach number, whirl angle, pitch angle, total pressure and static pressure. The probes were used to make time-resolved area traverses at two axial locations downstream of the rotor trailing edge. A 3D time-unsteady viscous Navier-Stokes solver was used for the numerical predictions. The unsteady exit flow from a turbine stage is formed from rotor-dependent phenomena (such as the rotor wake, the rotor trailing edge recompression shock, the tip-leakage flow and the hub secondary flow) and vane-rotor interaction dependant phenomena. This paper describes the time-resolved behaviour and three-dimensional migration paths of both of these phenomena as they convect downstream. It is shown that the inlet flow to a downstream vane is dominated by two corotating vortices, the first caused by the rotor tip-leakage flow and the second by the rotor hub secondary flow. At the inlet plane of the downstream vane the wake is extremely weak and the radial pressure gradient is shown to have caused the majority of the high loss wake fluid to be located between the mid-height of the passage and the casing wall. The structure of the flow indicates that between a high pressure stage and a downstream vane simple two-dimensional blade row interaction does not occur. The results presented in this paper indicate that the presence of an upstream stage is likely to significantly alter the structure of the secondary flow within a downstream vane. The paper also shows that vane-rotor interaction within the upstream stage causes a 10° circumferential variation in the inlet flow angle of the 2nd stage vane.

An Investigation on Aerodynamics Loss Mechanism of Squealer Tips of a High Pressure Turbine Blade Using URANS

2016 ◽  
Author(s):  
Jin-sol Jung ◽  
Okey Kwon ◽  
Changmin Son
Keyword(s):  
High Pressure ◽  
Turbine Blade ◽  
Wall Thickness ◽  
Suction Side ◽  
Leakage Flow ◽  
Pressure Side ◽  
Tip Leakage Flow ◽  
High Pressure Turbine ◽  
Loss Mechanism ◽  
Tip Leakage

The flow leaking over the tip of a high pressure turbine blade generates significant aerodynamic losses as it mixes with the mainstream flow. This study investigates the effect of blade tip geometries on turbine performance with both steady RANS and unsteady URANS analyses. Five different squealer geometries for a high pressure turbine blade have been examined: squealer on pressure side, squealer on suction side, cavity squealer, cavity squealer with pressure side cutback, and cavity squealer with suction side cutback. With the case of the cavity squealer, three different squealer wall thickness are investigated for the wall thickness (w) of 1x, 2x and 4x of the tip gap (G). The unsteady flow analyses using CFX have been conducted to investigate unsteady characteristics of the tip leakage flow and its influence on turbine performances. Through the comparison between URANS analyses, detailed vortex and wake structures are identified and studied at different fidelities. It is found that the over tip leakage flow loss is affected by the tip suction side geometry rather than that of the pressure side geometry. The unsteady results have contributed to resolve the fundamentals of vortex structures and aerodynamic loss mechanisms in a high pressure turbine stage.

Sign in / Sign up

Export Citation Format

Share Document