Development of Psi Factors for Thermal Bypass Due to Insulation Gaps in Low-Slope Roofing Assemblies

In commercial roofs, the presence or formation of gaps could be due to improper installation, thermal expansion, and dimensional changes in the insulation boards. The heat loss from these gaps could lead to higher thermal transmittance in the roof assembly. The current research study conducted around 70 experiments to investigate the effect of gap height, gap width and gap offset on the thermal transmittance of the roofing assembly. The measured data showed that in a staggered insulation layout with a joint offset of 610 mm (24 in), formation of 6.4 mm (1/4 in) to 12.7 mm (1/2 in) gaps at the insulation joints could contribute to an average decrease of 2% to 9% in the effective R-value of the roof assembly. As the insulation thermal resistance increases or becomes thicker, the thermal losses in the roof assembly increase. Generalized gap impact curves were developed to provide the relation between gap parameters (i.e., gap widths and height) and the thermal performance of the roof assembly. The experimental data were further analyzed using the psi factor approach of linear thermal bridging generating thermal transmittance data to support the calculation of thermal bypass from gaps in the thermal roof design.

ON RANDOM EXPECTED VALUES VARIATIONS OF TRIBOLOGY PARAMETERS IN HUMAN HIP JOINT SURFACES

This paper presents recent progress in the knowledge concerning the stochastic theory of bio- hydrodynamic lubrication with a phospholipids bilayer. On the basis of experimental measurements and analytical solutions, the research concerns the determination of the random expectancy values of load carrying capacity, the friction coefficient, and synovial fluid dynamic variations. After numerous measurements, it directly follows that the random density function of the gap height in the human joint usually indicates a disorderly increases and decreases in the height. Such irregular gap height variations have an important influence on the random synovial bio-fluid dynamic viscosity. This finally leads to the friction coefficient and cartilage wear changes of cooperating bio- surfaces. The main topic of this paper relates to the expectancy values of the tribology parameters localized inside the variable stochastic standard deviation intervals of the human joint gap height. The results obtained finally indicate the influence of the random roughness and growth of living biological cartilage surfaces on the expectancy values of the synovial fluid dynamic viscosity, load carrying capacity and friction forces in human hip joints.

An EHL Extension of the Unsteady FBNS Algorithm

Many engineering applications rely on lubricated gaps where the hydrodynamic pressure distribution is influenced by cavitation phenomena and elastic deformations. To obtain details about the conditions within the lubricated gap, solvers are required that can model cavitation and elastic deformation effects efficiently when a large amount of discretization cells is employed. The presented unsteady EHL-FBNS solver can compute the solution of such large problems that require the consideration of both mass-conserving cavitation and elastic deformation. The execution time of the presented algorithm scales almost with N log(N) where N is the number of computational grid points. A detailed description of the algorithm and the discretized equations is presented. The MATLAB© code is provided in the supplements along with a maintained version on GitHub to encourage its usage and further development. The output of the solver is compared to and validated with simulated and experimental results from the literature to provide a detailed comparison of different discretization schemes of the Couette term in presence of gap height discontinuities. As a final result, the most favourable scheme is identified for the unsteady study of surface textures in ball-on-disc tribometers under severe EHL conditions.

Study on the determination of the parameters of the electric purifier

The article is devoted to the determination of the parameters on which the filter performance depends on the hydrodynamic, electromagnetic and geometrical parameters of the fluid and pollution. These include fluid viscosity and flow rate, magnetizing force, particle size of contamination, gap height, and the distance between the turns.

Simulation of Possible Fire and Explosion Hazards of Clean Fuel Vehicles in Garages

Clean fuel is advocated to be used for sustainability. The number of liquefied petroleum gas (LPG) and hydrogen vehicles is increasing globally. Explosion hazard is a threat. On the other hand, the use of hydrogen is under consideration in Hong Kong. Explosion hazards of these clean fuel (LPG and hydrogen) vehicles were studied and are compared in this paper. The computational fluid dynamics (CFD) software Flame Acceleration Simulator (FLACS) was used. A car garage with a rolling shutter as its entrance was selected for study. Dispersion of LPG from the leakage source with ignition at a higher position was studied. The same garage was used with a typical hydrogen vehicle leaking 3.4 pounds (1.5 kg) of hydrogen in 100 s, the mass flow rate being equal to 0.015 kgs−1. The hydrogen vehicle used in the simulation has two hydrogen tanks with a combined capacity of 5 kg. The entire tank would be completely vented out in about 333 s. Two scenarios of CFD simulation were carried out. In the first scenario, the rolling shutter was completely closed and the leaked LPG or hydrogen was ignited at 300 s after leakage. The second scenario was conducted with a gap height of 0.3 m under the rolling shutter. Predicted results of explosion pressure and temperature show that appropriate active fire engineering systems are required when servicing these clean fuel vehicles in garages. An appropriate vent in an enclosed space such as the garage is important in reducing explosion hazards.

Phase-Sensitive Optical Coherence Microscopy of Integrated Nanophotonics Devices

We report on the development of a new approach for studying the internal structure of polymer integrated nanophotonics devices using phase-sensitive optical coherence microscopy. Visualization and flaw detection of devices and their internal structure was carried out using the example of coupling gratings and prisms for a miniature Otto configuration with a characteristic gap height of 50-300 nm.

Virtual Stencil for Patterning and Modeling in a Quantitative Volume Using EWOD and DEP Devices for Microfluidics

Applying microfluidic patterning, droplets were precisely generated on an electrowetting-on-dielectric (EWOD) chip considering these parameters: number of generating electrodes, number of cutting electrodes, voltage, frequency and gap between upper and lower plates of the electrode array on the EWOD chip. In a subsequent patterning experiment, an environment with three generating electrodes, one cutting electrode and a gap height 10 μm, we obtained a quantitative volume for patterning. Propylene carbonate liquid and a mixed colloid of polyphthalate carbonate (PPC) and photosensitive polymer material were manipulated into varied patterns. With support from a Z-axis lifting platform and a UV lamp, a cured 3D structure was stacked. Using an EWOD system, a multi-layer three-dimensional structure was produced for the patterning. A two-plate EWOD system patterned propylene carbonate in a quantitative volume at 140 Vpp/20 kHz with automatic patterning.

Swimming of the Trophont Zooid of Vorticella Convallaria

Vorticella convallaria is a ciliated protozoan found in freshwater habitats. In the sessile or stalked trophont form, V. convallaria is shaped somewhat like a balloon as it has a body or zooid (the head of the balloon) that is about 40 μm large with cilia around its oral part, and a stalk (the string of a balloon) anchoring the zooid to a solid surface. When a trophont zooid of V. convallaria detached from the stalk, the zooid swims around in water by creating water flow using its oral cilia. In contrast to the stalk contraction of V. convallaria that has been well studied, the swimming motility of V. convallaria is little known. In this study, we measured the swimming trajectories of the stalkless trophont zooid of V. convallaria using video microscopy and Hele-Shaw cells with a gap height of 25 μm, traced the swimming zooid using image processing, and analyzed the swimming motion in terms of swimming velocity and mean square displacement. The stalkless trophont zooid of V . convallaria was found to swim in circular patterns with intermittent ballistic motions in the confinement, and the average swimming speed ranged from 20 μm/s to 110 μm/s. Since the swimming pattern of V. convallaria appeared to be affected by the level of confinement, we will continue characterizing the ciliate’s swimming in the Hele-Shaw cell with different gap heights. Our study is expected to reveal the swimming motility of V. convallaria and to advance general understanding of swimming of microorganisms.

An Investigation into the Effect of Rolling Reduction on 3D Curved Parts Rolling Process

Rolling technology based on arc-shaped rollers is a novel method for rapid manufacturing of 3D curved parts. The method uses a pair of arc-shaped rollers (a convex roller and a concave roller) as forming tools, forming an unevenly distributed roll gap. The sheet metal has both transverse bending and longitudinal uneven extension during rolling, so that surface parts with double curvature are processed. The curvature of the formed surface part can be changed by changing the rolling reduction. Changing the vertical distance between the rollers will cause the overall change of the roll gap height, which will inevitably have a great impact on the forming effect of formed 3D curved parts. In this paper, a finite element model and experiment with different rolling reductions was designed; the influence of rolling reduction on the bending deformation and shape accuracy of formed 3D curved parts was studied. The results show that, with the slight increase of rolling reduction (from 0.04 to 0.12 mm), the longitudinal bending deformation of the formed 3D curved part increases significantly, but its transversal bending is almost not affected. When the maximum rolling reduction is 0.04 and 0.06 mm (the corresponding minimum rolling reduction is less than or equal to zero), the shape accuracy of the formed 3D curved parts is not good enough; when the maximum rolling reduction is greater than 0.06 mm (the corresponding minimum rolling reduction is greater than zero), the shape accuracy of the formed 3D curved parts is significantly better. This indicates that, for the rolling of 3D curved parts based on arc-shaped rollers, ensuring that the minimum rolling reduction is greater than zero is the key to ensuring good shape accuracy of the formed 3D curved parts.