scholarly journals Numerical simulation of fuel dribbling and nozzle wall wetting

2021 ◽  
pp. 146808742098518
Author(s):  
Manolis Gavaises ◽  
Mithun Murali-Girija ◽  
Carlos Rodriguez ◽  
Phoevos Koukouvinis ◽  
Martin Gold ◽  
...  
Keyword(s):  
Stokes Equations ◽  
Navier Stokes ◽  
Needle Valve ◽  
Immersed Boundary ◽  
Nozzle Wall ◽  
Two Phase ◽  
Navier Stokes Equations ◽  
Start Of Injection ◽  
Wall Wetting ◽  
Eccentric Motion

The present work describes a numerical methodology and its experimental validation of the flow development inside and outside of the orifices during a pilot injection, dwelt time and the subsequent start of injection cycle. The compressible Navier-Stokes equations are numerically solved in a six-hole injector imposing realistic conditions of the needle valve movement and considering in addition a time-dependent eccentric motion. The valve motion is simulated using the immersed boundary method; this allows for simulations to be performed at zero lift during the dwelt time between successive injections, where the needle remains closed. Moreover, the numerical model utilises a fully compressible two-phase (liquid, vapour) two-component (fuel, air) barotropic model. The air’s motion is simulated with an additional transport equation coupled with the VOF interface capturing method able to resolve the near-nozzle atomisation and the resulting impact of the injected liquid on the oleophilic nozzle wall surfaces. The eccentric needle motion is found to be responsible for the formation of strong swirling flows inside the orifices, which not only contributes to the breakup of the injected liquid jet into ligaments but also to their backwards motion towards the external wall surface of the injector. Model predictions suggest that such nozzle wall wetting phenomena are more pronounced during the closing period of the valve and the re-opening of the nozzle, due to the residual gases trapped inside the nozzle, and which contribute to the poor atomisation of the injected fluid upon re-opening of the needle valve in subsequent injection events.

Numerical Modeling of Evolution of Boundary Between Incompressible Gas and Liquid in Two-Dimensional Region

2006 ◽  
Vol 4 ◽  
pp. 224-236
Author(s):  
A.S. Topolnikov
Keyword(s):  
Numerical Modeling ◽  
Interphase Boundary ◽  
Incompressible Liquid ◽  
Stokes Equations ◽  
Numerical Code ◽  
Navier Stokes ◽  
Two Phase ◽  
Navier Stokes Equations ◽  
Incompressible Media ◽  
Good Agreement

The paper is devoted to numerical modeling of Navier–Stokes equations for incompressible media in the case, when there exist gas and liquid inside the rectangular calculation region, which are separated by interphase boundary. The set of equations for incompressible liquid accounting for viscous, gravitational and surface (capillary) forces is solved by finite-difference scheme on the spaced grid, for description of interphase boundary the ideology of Level Set Method is used. By developed numerical code the set of hydrodynamic problems is solved, which describe the motion of two-phase incompressible media with interphase boundary. As a result of numerical simulation the solutions are obtained, which are in good agreement with existing analytical and experimental solutions.

NUMERICAL SIMULATION OF ISOTHERMAL AND THERMAL TWO-PHASE FLOWS USING PHASE-FIELD MODELING

2007 ◽  
Vol 18 (04) ◽  
pp. 536-545 ◽  
Author(s):  
NAOKI TAKADA ◽  
AKIO TOMIYAMA
Keyword(s):  
Phase Field ◽  
Stokes Equations ◽  
Density Ratio ◽  
Navier Stokes ◽  
Phase Field Modeling ◽  
Two Phase Flows ◽  
Two Phase ◽  
Navier Stokes Equations ◽  
Field Modeling ◽  
High Density Ratio

For interface-tracking simulation of two-phase flows in various micro-fluidics devices, we examined the applicability of two versions of computational fluid dynamics method, NS-PFM, combining Navier-Stokes equations with phase-field modeling for interface based on the van der Waals-Cahn-Hilliard free-energy theory. Through the numerical simulations, the following major findings were obtained: (1) The first version of NS-PFM gives good predictions of interfacial shapes and motions in an incompressible, isothermal two-phase fluid with high density ratio on solid surface with heterogeneous wettability. (2) The second version successfully captures liquid-vapor motions with heat and mass transfer across interfaces in phase change of a non-ideal fluid around the critical point.

scholarly journals Do the Volume-of-Fluid and the Two-Phase Euler Compete for Modeling a Spillway Aerator?

Water ◽  
2021 ◽  
Vol 13 (21) ◽  
pp. 3092
Author(s):  
Lourenço Sassetti Mendes ◽  
Javier L. Lara ◽  
Maria Teresa Viseu
Keyword(s):  
Stokes Equations ◽  
Cost Benefit ◽  
Volume Of Fluid ◽  
Navier Stokes ◽  
Type Model ◽  
Two Phase ◽  
Navier Stokes Equations ◽  
Entrained Air ◽  
Computational Resources ◽  
Mesh Convergence

Spillway design is key to the effective and safe operation of dams. Typically, the flow is characterized by high velocity, high levels of turbulence, and aeration. In the last two decades, advances in computational fluid dynamics (CFD) made available several numerical tools to aid hydraulic structures engineers. The most frequent approach is to solve the Reynolds-averaged Navier–Stokes equations using an Euler type model combined with the volume-of-fluid (VoF) method. Regardless of a few applications, the complete two-phase Euler is still considered to demand exorbitant computational resources. An assessment is performed in a spillway offset aerator, comparing the two-phase volume-of-fluid (TPVoF) with the complete two-phase Euler (CTPE). Both models are included in the OpenFOAM® toolbox. As expected, the TPVoF results depend highly on the mesh, not showing convergence in the maximum chute bottom pressure and the lower-nappe aeration, tending to null aeration as resolution increases. The CTPE combined with the k–ω SST Sato turbulence model exhibits the most accurate results and mesh convergence in the lower-nappe aeration. Surprisingly, intermediate mesh resolutions are sufficient to surpass the TPVoF performance with reasonable calculation efforts. Moreover, compressibility, flow bulking, and several entrained air effects in the flow are comprehended. Despite not reproducing all aspects of the flow with acceptable accuracy, the complete two-phase Euler demonstrated an efficient cost-benefit performance and high value in spillway aerated flows. Nonetheless, further developments are expected to enhance the efficiency and stability of this model.

scholarly journals A Stress Mapping Immersed Boundary Method for Viscous Flows

2021 ◽  
Vol 87 (3) ◽  
pp. 1-20
Author(s):  
Karim M. Ali ◽  
Mohamed Madbouli ◽  
Hany M. Hamouda ◽  
Amr Guaily
Keyword(s):  
Immersed Boundary Method ◽  
Stokes Equations ◽  
Cross Flow ◽  
Navier Stokes ◽  
Immersed Boundary ◽  
Element Formulation ◽  
Navier Stokes Equations ◽  
Boundary Method ◽  
Background Grid ◽  
Dimensional Simulation

This work introduces an immersed boundary method for two-dimensional simulation of incompressible Navier-Stokes equations. The method uses flow field mapping on the immersed boundary and performs a contour integration to calculate immersed boundary forces. This takes into account the relative location of the immersed boundary inside the background grid elements by using inverse distance weights, and also considers the curvature of the immersed boundary edges. The governing equations of the fluid mechanics are solved using a Galerkin-Least squares finite element formulation. The model is validated against a stationary and a vertically oscillating circular cylinder in a cross flow. The results of the model show acceptable accuracy when compared to experimental and numerical results.

Modeling of Cell Motion in Micro-Scale Hydrodynamic-Electrical Field

2009 ◽  
Vol 74 ◽  
pp. 139-142
Author(s):  
Ting Ye ◽  
Hua Li
Keyword(s):  
Stokes Equations ◽  
Elastic Shell ◽  
Practical Significance ◽  
Cell Manipulation ◽  
Navier Stokes ◽  
Phase System ◽  
Two Phase ◽  
Navier Stokes Equations ◽  
Maxwell Stress Tensor ◽  
Cell Motion

A modeling of two-phase system is presented for investigation of the cell motion and deformation in the microchannel subject to the mechanical and electrical coupled forces. In order to evaluate the mechanical force developed by cell membrane, it is treated as an incompressible and elastic shell with uniform thickness capable of shearing and bending deformation. Due to the irregular and complex cell configuration after deformation, the Maxwell stress tensor (MST) method is successfully employed to analyze the dielectrophoretic force. The modified particle binary level set (MPBLS) method is presented to accurately track the moving interface between the two phases, which is vital for a modeling of two-phase system. Afterwards the modified SIMPLER coupled with SIMPLEC is used to numerically solve the incompressible Navier-Stokes equations governing the entire flow field. On basis of the series of methods, the motion and deformation of red blood cell (RBC) in the microchannel under the mechanical and electrical forces are simulated to demonstrate the deformation process and the moving trajectory of RBC. The present study is not only of great value for deeper understanding of some diseases caused by cell abnormality, but also of practical significance for cell manipulation and separation.

Discussion on Clustering Effects in Vertical Gas-Particle Flows

2000 ◽  
Author(s):  
Eivind Helland ◽  
Rene Occelli ◽  
Lounes Tadrist
Keyword(s):  
Gas Phase ◽  
Stokes Equations ◽  
Lagrangian Approach ◽  
Inelastic Collisions ◽  
Navier Stokes ◽  
Coupling Term ◽  
Two Phase ◽  
Navier Stokes Equations ◽  
Drag Forces ◽  
Particle Flows

Abstract Simulations of 2D gas-particle flows in a vertical riser using a mixed Eulerian-Lagrangian approach are addressed. The model for the interstitial gas phase is based on the Navier-Stokes equations for two-phase flow with a coupling term between the gas and solid phases due to drag forces. The motion of particles is treated by a Lagrangian approach and the particles are assumed to interact through binary, instantaneous, non-frontal, inelastic collisions with friction. In this paper different particle clustering effects in the gas-particle flow is investigated.

Sign in / Sign up

Export Citation Format

Share Document