Control-oriented modeling of the gas exchange process in rebreathing homogeneous charge compression ignition engines

2021 ◽  
pp. 146808742110368
Author(s):  
Akihiro Takeshita ◽  
Yudai Yamasaki ◽  
Mitsuhiro Muto ◽  
Takayuki Hikita ◽  
Takuma Fujii ◽  
...  
Keyword(s):  
Gas Exchange ◽  
High Efficiency ◽  
Homogeneous Charge Compression Ignition ◽  
Exchange Process ◽  
Simulation Software ◽  
Compression Ignition ◽  
Hcci Engine ◽  
Calculation Step ◽  
Gas Exchange Process ◽  
Homogeneous Charge

The purpose of this study is to develop a model for the gas exchange process in a rebreathing homogeneous charge compression ignition (HCCI) engine. HCCI engines are attracting significant attention due to their low emissions and high efficiency. To design the control system of an HCCI engine, it is necessary to develop a control-oriented engine model. The developed model lowers its computational load by combining two types of models. The model consists of a discrete model for the exhaust process (the first half of the gas exchange process) and a continuous model with a variable calculation step size for the rebreathing process (the latter half of the gas exchange process). Also, the constructed model maintained its prediction accuracy, as the pressure pulsation in the exhaust port was modeled, and an unsteady flow equation was used. It was confirmed that the model developed for the gas exchange process calculated in about half time of one cycle and reproduced the results of 1D engine simulation software with a maximum error of about 10% in the in-cylinder pressure, temperature, and trapped mass.

scholarly journals Development and experimental validation of a real-time capable field programmable gate array–based gas exchange model for negative valve overlap

2018 ◽  
Vol 21 (3) ◽  
pp. 421-436 ◽  
Author(s):  
David Gordon ◽  
Christian Wouters ◽  
Maximilian Wick ◽  
Feihong Xia ◽  
Bastian Lehrheuer ◽  
...  
Keyword(s):  
Gas Exchange ◽  
Real Time ◽  
Field Programmable Gate Array ◽  
Homogeneous Charge Compression Ignition ◽  
Exchange Process ◽  
Compression Ignition ◽  
Field Programmable ◽  
Gate Array ◽  
Gas Exchange Process ◽  
Homogeneous Charge

Homogeneous charge compression ignition has the potential to significantly reduce NO x emissions, while maintaining a high fuel efficiency. Homogeneous charge compression ignition is characterized by compression-induced autoignition of a lean homogeneous air–fuel mixture. Combustion timing is highly dependent on the in-cylinder state including pressure, temperature and trapped mass. To control homogeneous charge compression ignition combustion, it is necessary to have an accurate representation of the gas exchange process. Currently, microprocessor-based engine control units require that the gas exchange process is linearized around a desired operating point to simplify the model for real-time implementation. This reduces the models’ ability to handle disturbances and limits the flexibility of the model. However, using a field programmable gate array, a detailed simulation of the physical gas exchange process can be implemented in real time. This paper outlines the process of converting physical governing equations to an offline zero-dimensional gas exchange model. The process used to convert this model to a field programmable gate array capable model is described. This model is experimentally validated using a single cylinder research engine with electromagnetic valves to record real-time field programmable gate array gas exchange results and comparing to the offline zero-dimensional physical model. The field programmable gate array model is able to accurately calculate the cylinder temperature and cylinder mass at 0.1 °CA intervals during the gas exchange process for a range of negative valve overlaps, boost conditions and engine speeds making the model useful for future real-time control applications.

scholarly journals Influence of gas composition on the combustion and efficiency of a homogeneous charge compression ignition engine system fuelled with methanol reformed gases

2008 ◽  
Vol 9 (5) ◽  
pp. 399-408 ◽  
Author(s):  
T Shudo
Keyword(s):  
Homogeneous Charge Compression Ignition ◽  
Waste Heat ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Temperature Oxidation ◽  
Hcci Engine ◽  
Recovery Capacity ◽  
Exhaust Heat ◽  
Engine System ◽  
Homogeneous Charge

A homogeneous charge compression ignition (HCCI) engine system fuelled with dimethyl ether (DME) and methanol-reformed gas (MRG), both produced from methanol by onboard reformers using exhaust heat, has been proposed in previous research. Adjusting the proportions of DME and MRG with different ignition properties effectively controlled the ignition timing and load in HCCI combustion. The use of the single liquid fuel, methanol, also eliminates the inconvenience of carrying two fuels while maintaining the effective ignition control effect. Because reactions producing DME and MRG from methanol are endothermic, a part of the exhaust gas heat energy can be recovered during the fuel reforming. Methanol can be reformed into various compositions of hydrogen, carbon monoxide, and carbon dioxide. The present paper aims to establish the optimum MRG composition for the system in terms of ignition control and overall efficiency. The results show that an increased hydrogen fraction in MRG retards the onset of high-temperature oxidation and permits operation with higher equivalence ratios. However, the MRG composition affects the engine efficiency only a little, and the MRG produced by the thermal decomposition having the best waste-heat recovery capacity brings the highest overall thermal efficiency in the HCCI engine system fuelled with DME and MRG.

Sign in / Sign up

Export Citation Format

Share Document