Shallow 3-D seismic reflection surveying: Data acquisition and preliminary processing strategies

Geophysics ◽  
1998 ◽  
Vol 63 (4) ◽  
pp. 1434-1450 ◽  
Author(s):  
Frank Büker ◽  
Alan G. Green ◽  
Heinrich Horstmeyer
Keyword(s):  
Data Acquisition ◽  
Seismic Reflection ◽  
Full Range ◽  
Depth Range ◽  
Data Set ◽  
Processing Scheme ◽  
Seismic Reflection Data ◽  
Near Surface ◽  
Glacial Sediments ◽  
Reflection Data

A comprehensive strategy of 3-D seismic reflection data acquisition and processing has been used in a study of glacial sediments deposited within a Swiss mountain valley. Seismic data generated by a downhole shotgun source were recorded with single 30-Hz geophones distributed at 3 m × 3 m intervals across a 357 m × 432 m area. For most common‐midpoint (CMP) bins, traces covering a full range of azimuths and source‐receiver distances of ∼2 to ∼125 m were recorded. A common processing scheme was applied to the entire data set and to various subsets designed to simulate data volumes collected with lower density source and receiver patterns. Comparisons of seismic sections extracted from the processed 3-D subsets demonstrated that high‐fold (>40) and densely spaced (CMP bin sizes ⩽ 3 m × 3 m) data with relatively large numbers (>6) of traces recorded at short (<20 m) source‐receiver offsets were essential for obtaining clear images of the shallowest (<100 ms) reflecting horizons. Reflections rich in frequencies >100 Hz at traveltimes of ∼20 to ∼170 ms provided a vertical resolution of 3 to 6 m over a depth range of ∼15 to ∼150 m. The shallowest prominent reflection at 20 to 35 ms (∼15 to 27 m depth) originated from the boundary between a near‐surface sequence of clays/silts and an underlying unit of heterogeneous sands/gravels.

scholarly journals Using Seismic Attributes in seismotectonic research: an application to the Norcia's Mw = 6.5 earthquake (30th October 2016) in Central Italy

2019 ◽  
Author(s):  
Maurizio Ercoli ◽  
Emanuele Forte ◽  
Massimiliano Porreca ◽  
Ramon Carbonell ◽  
Cristina Pauselli ◽  
...  
Keyword(s):  
Seismic Reflection ◽  
Central Italy ◽  
Seismic Attributes ◽  
Seismic Attribute ◽  
Data Set ◽  
Epicentral Zone ◽  
Seismic Reflection Data ◽  
Near Surface ◽  
Reflection Data ◽  
Attribute Analysis

Abstract. In seismotectonic studies, seismic reflection data are a powerful tool to unravel the complex deep architecture of active faults. Such tectonic structures are usually mapped at surface through traditional geological surveying whilst seismic reflection data may help to trace their continuation from the near-surface down to hypocentral depth. In this study, we propose the application of the seismic attributes technique, commonly used in seismic reflection exploration by oil industry, to seismotectonic research for the first time. The study area is a geologically complex region of Central Italy, recently struck by a long-lasting seismic sequence including a Mw 6.5 main-shock. A seismic reflection data-set consisting of three vintage seismic profiles, currently the only available across the epicentral zone, constitutes a singular opportunity to attempt a seismic attribute analysis. This analysis resulted in peculiar seismic signatures which generally correlate with the exposed surface geologic features, and also confirming the presence of other debated structures. These results are critical, because provide information also on the relatively deep structural setting, mapping a prominent, high amplitude regional reflector that marks the top basement, interpreted as important rheological boundary. Complex patterns of high-angle discontinuities crossing the reflectors have been also identified. These dipping fabrics are interpreted as the expression of fault zones, belonging to the active normal fault systems responsible for the seismicity of the region. This work demonstrates that seismic attribute analysis, even if used on low-quality vintage 2D data, may contribute to improve the subsurface geological interpretation of areas characterized by high seismic potential.

scholarly journals Time-lapse imaging using 3D ultra-high-frequency marine seismic reflection data

Geophysics ◽  
2020 ◽  
Vol 85 (2) ◽  
pp. P13-P25
Author(s):  
Michael J. Faggetter ◽  
Mark E. Vardy ◽  
Justin K. Dix ◽  
Jonathan M. Bull ◽  
Timothy J. Henstock
Keyword(s):  
High Frequency ◽  
Seismic Reflection ◽  
High Tide ◽  
Time Lapse ◽  
Data Set ◽  
Seismic Reflection Data ◽  
Near Surface ◽  
Ultra High Frequency ◽  
Reflection Data ◽  
Marine Seismic

Time-lapse (4D) seismic imaging is now widely used as a tool to map and interpret changes in deep reservoirs as well as investigate dynamic, shallow hydrological processes in the near surface. However, there are very few examples of time-lapse analysis using ultra-high-frequency (UHF; kHz range) marine seismic reflection data. Exacting requirements for navigation can be prohibitive for acquiring coherent, true-3D volumes. Variable environmental noise can also lead to poor amplitude repeatability and make it difficult to identify differences that are related to real physical changes. Overcoming these challenges opens up a range of potential applications for monitoring the subsurface at decimetric resolution, including geohazards, geologic structures, as well as the bed-level and subsurface response to anthropogenic activities. Navigation postprocessing was incorporated to improve the acquisition and processing workflow for the 3D Chirp subbottom profiler and provide stable, centimeter-level absolute positioning, resulting in well-matched 3D data and mitigating 4D noise for data stacked into [Formula: see text] common-midpoint bins. Within an example 4D data set acquired on the south coast of the UK, interpretable differences are recorded within a shallow gas blanket. Reflections from the top and bottom of a gas pocket are imaged at low tide, whereas at high tide only the upper reflection is imaged. This case study demonstrates the viability of time-lapse UHF 3D seismic reflection for quantitative mapping of decimeter-scale changes within the shallow marine subsurface.

scholarly journals Active deformation evidence in the offshore of western Calabria (southern Tyrrhenian Sea) from ultra-resolution multichannel seismic reflection data: results from the Gulf of Sant'Eufemia

2020 ◽  
Author(s):  
Fabrizio Pepe ◽  
Mor Kanari ◽  
Pierfrancesco Burrato ◽  
Marta Corradino ◽  
Henrique Duarte ◽  
...  
Keyword(s):  
Data Acquisition ◽  
Seismic Reflection ◽  
Fault System ◽  
Tyrrhenian Sea ◽  
Seismic Profiles ◽  
Data Set ◽  
Seismic Reflection Data ◽  
Reflection Data ◽  
Multichannel Seismic Reflection Data ◽  
Earthquake Potential

&lt;p&gt;An ultra-resolution, multichannel seismic reflection data set was collected during an oceanographic cruise organised in the frame of the &amp;#8220;&lt;em&gt;Earthquake Potential of Active Faults using offshore Geological and Morphological Indicators&lt;/em&gt;&amp;#8221; (EPAF) project, which was founded by the Scientific and Technological Cooperation (Scientific Track 2017) between the Italian Ministry of Foreign Affairs and International Cooperation and the Ministry of Science, Technology and Space of the State of Israel. The data acquisition approach was based on innovative technologies for the offshore imaging of stratigraphy and structures along continental margins with a horizontal and vertical resolution at decimetric scale. In this work, we present the methodology used for the 2D HR-seismic reflection data acquisition and the preliminary interpretation of the data set. The 2D seismic data were acquired onboard the R/V Atlante by using an innovative data acquisition equipment composed by a dual-sources Sparker system and one HR 48-channel, slant streamers, with group spacing variable from 1 to 2 meters, at 10 kHz sampling rate. An innovative navigation system was used to perform all necessary computations to determining real-time positions of sources and receivers. The resolution of the seismic profiles obtained from this experiment is remarkable high respect to previously acquired seismic data for both scientific and industrial purposes. In addition to the seismic imaging, gravity core data were also collected for sedimentological analysis and to give a chronological constraint using radiocarbon datings to the shallower reflectors. The investigated area is located in the western offshore sector of the Calabrian Arc (southern Tyrrhenian Sea) where previous research works, based on multichannel seismic profiles coupled with Chirp profiles, have documented the presence of an active fault system. One of the identified faults was tentatively considered as the source of the Mw 7, 8 September 1905 seismic event that hit with highest macroseismic intensities the western part of central Calabria, and was followed by a tsunami that inundated the coastline between Capo Vaticano and the Angitola plain. On this basis, the earthquake was considered to have a source at sea, but so far, the location, geometry and kinematics of the causative fault are still poorly understood. In this study we provide preliminary results of the most technologically advanced ultra-high-resolution geophysical method used to reveal the 3D faulting pattern, the late Quaternary slip rate and the earthquake potential of the marine fault system located close to the densely populated west coast of Calabria.&lt;/p&gt;

Reducing source‐generated noise in shallow seismic data using linear and hyperbolic τ‐p transformations

Geophysics ◽  
2001 ◽  
Vol 66 (5) ◽  
pp. 1612-1621 ◽  
Author(s):  
Roman Spitzer ◽  
Frank O. Nitsche ◽  
Alan G. Green
Keyword(s):  
Seismic Reflection ◽  
Guided Waves ◽  
Relative Strength ◽  
Data Set ◽  
Processing Scheme ◽  
Seismic Reflection Data ◽  
Northern Switzerland ◽  
Reflection Data ◽  
Shallow Seismic ◽  
P Domain

High‐resolution seismic reflection data recorded at many locations on the earth are plagued by the overwhelming effects of direct, refracted, guided, and surface waves. These different components of source‐generated noise may completely mask reflections at traveltimes <∼50–100 ms. Conventional processing methods that include the time‐consuming application of mute functions may lead to the misprocessing of source‐generated noise (especially guided waves) as reflected events and/or the unintentional removal of important shallow reflections. We introduce a combined linear and hyperbolic τ‐p processing scheme that results in the effective separation of reflections from source‐generated noise. After applying linear moveout terms that adjust the direct, refracted, and guided arrivals to appear horizontal to subhorizontal, the reduced traveltime shot gathers are transformed into the linear τ‐p domain. It is then straightforward to design a single τ‐p filter that eliminates most of the source‐generated noise throughout the entire data set. Following inverse linear τ‐p transformation and removal of the linear moveout terms, the filtered shot gathers contain reflections and residual elements of the source‐generated noise. Because summing along hyperbolas favors reflections, transforming the filtered shot gathers into the hyperbolic τ‐p domain leads to significant enhancements in the S/N ratio. A simple rescaling of data values in the hyperbolic τ‐p domain, which results in the loss of true amplitude information, increases further the relative strength of the reflected signals. Finally, inverse hyperbolic transformation yields shot gathers dominated by reflections. In tests of the combined τ‐p processing scheme on a synthetic shot gather and on a complete shallow seismic reflection data set recorded in northern Switzerland, significant improvements in the quality of reflections in the prestacked data and on a fully processed section are readily apparent. According to the results of these tests, the new scheme works well for reflections originating from flat and dipping horizons.

Migration of shallow seismic reflection data

Geophysics ◽  
1994 ◽  
Vol 59 (3) ◽  
pp. 402-410 ◽  
Author(s):  
Ross A. Black ◽  
Don W. Steeples ◽  
Richard D. Miller
Keyword(s):  
Seismic Reflection ◽  
Large Data ◽  
Flow Chart ◽  
Seismic Section ◽  
Data Set ◽  
Seismic Reflection Data ◽  
Near Surface ◽  
Reflection Data ◽  
Shallow Seismic ◽  
Simple Set

We present an analysis of migration effects on seismic reflection images of very shallow targets such as those that are common objectives of engineering, groundwater, and environmental investigations. We use an example of seismic reflection data from depths of 5 to 15 m that show negligible effect from migration, despite the apparent steep dip on the seismic section. Our analysis of the question of when to migrate shallow reflection data indicates it is critical to take into account the highly variable near‐surface velocities and the vertical exaggeration on the seismic section. A simple set of calculations is developed as well as a flow chart based on the “migrator’s equation” that can predict whether migration of an arbitrary shallow seismic section is advisable. Because shallow reflection data are often processed on personal computers, unnecessary migration of a large data set can be prohibitively time‐consuming and wasteful.

Shallow seismic reflection study of a glaciated valley

Geophysics ◽  
1998 ◽  
Vol 63 (4) ◽  
pp. 1395-1407 ◽  
Author(s):  
Frank Büker ◽  
Alan G. Green ◽  
Heinrich Horstmeyer
Keyword(s):  
Seismic Reflection ◽  
High Amplitude ◽  
Data Sets ◽  
Seismic Section ◽  
Data Set ◽  
Seismic Reflection Data ◽  
Northern Switzerland ◽  
Reflection Data ◽  
Shallow Seismic ◽  
Glaciated Valley

Shallow seismic reflection data were recorded along two long (>1.6 km) intersecting profiles in the glaciated Suhre Valley of northern Switzerland. Appropriate choice of source and receiver parameters resulted in a high‐fold (36–48) data set with common midpoints every 1.25 m. As for many shallow seismic reflection data sets, upper portions of the shot gathers were contaminated with high‐amplitude, source‐generated noise (e.g., direct, refracted, guided, surface, and airwaves). Spectral balancing was effective in significantly increasing the strength of the reflected signals relative to the source‐generated noise, and application of carefully selected top mutes ensured guided phases were not misprocessed and misinterpreted as reflections. Resultant processed sections were characterized by distributions of distinct seismic reflection patterns or facies that were bounded by quasi‐continuous reflection zones. The uppermost reflection zone at 20 to 50 ms (∼15 to ∼40 m depth) originated from a boundary between glaciolacustrine clays/silts and underlying glacial sands/gravels (till) deposits. Of particular importance was the discovery that the deepest part of the valley floor appeared on the seismic section at traveltimes >180 ms (∼200 m), approximately twice as deep as expected. Constrained by information from boreholes adjacent to the profiles, the various seismic units were interpreted in terms of unconsolidated glacial, glaciofluvial, and glaciolacustrine sediments deposited during two principal phases of glaciation (Riss at >100 000 and Würm at ∼18 000 years before present).

Migration with reduced artifacts from internal multiple reflections

Geophysics ◽  
2020 ◽  
Vol 85 (4) ◽  
pp. A25-A29
Author(s):  
Lele Zhang
Keyword(s):  
Seismic Reflection ◽  
Computational Cost ◽  
Data Sets ◽  
Square Root ◽  
Multiple Reflections ◽  
Data Set ◽  
Seismic Reflection Data ◽  
Reflection Data ◽  
Recent Developments ◽  
Multiple Elimination

Migration of seismic reflection data leads to artifacts due to the presence of internal multiple reflections. Recent developments have shown that these artifacts can be avoided using Marchenko redatuming or Marchenko multiple elimination. These are powerful concepts, but their implementation comes at a considerable computational cost. We have derived a scheme to image the subsurface of the medium with significantly reduced computational cost and artifacts. This scheme is based on the projected Marchenko equations. The measured reflection response is required as input, and a data set with primary reflections and nonphysical primary reflections is created. Original and retrieved data sets are migrated, and the migration images are multiplied with each other, after which the square root is taken to give the artifact-reduced image. We showed the underlying theory and introduced the effectiveness of this scheme with a 2D numerical example.

Sign in / Sign up

Export Citation Format

Share Document