Fault whispers: Transmission distortions on prestack seismic reflection data

Geophysics ◽  
2000 ◽  
Vol 65 (2) ◽  
pp. 377-389 ◽  
Author(s):  
Paul J. Hatchell
Keyword(s):  
Seismic Data ◽  
Seismic Waves ◽  
Shallow Gas ◽  
Seismic Reflection Data ◽  
Reflection Data ◽  
Amplitude Versus Offset ◽  
Velocity Changes ◽  
Transmission Distortions ◽  
Amplitude Versus ◽  
Buried Faults

Transmission distortions are observed on prestack seismic data at two locations in the Gulf of Mexico. These distortions produce anomalous amplitude versus offset (AVO) signatures. The locations of the distortion zones are determined using acquisition geometry and ray tracing. No obvious reflection events, such as shallow gas zones, are observed at the predicted locations of the distortion zones. Instead, the distortion zones correlate with buried faults and unconformities. It is postulated that the distortions are produced by velocity changes across buried faults and unconformities. The distortions result from an interference pattern resulting from seismic waves arriving from different sides of the faults. A simple model is developed to explain many of the characteristics of the distortion pattern.

An improved method to estimate Q based on the logarithmic spectrum of moving peak points

2019 ◽  
Vol 7 (2) ◽  
pp. T255-T263 ◽  
Author(s):  
Yanli Liu ◽  
Zhenchun Li ◽  
Guoquan Yang ◽  
Qiang Liu
Keyword(s):  
Seismic Waves ◽  
Wave Attenuation ◽  
Real Data ◽  
Peak Frequency ◽  
Seismic Reflection Data ◽  
The Real ◽  
Time Frequency ◽  
Reflection Data ◽  
Text Filtering ◽  
The Impact

The quality factor ([Formula: see text]) is an important parameter for measuring the attenuation of seismic waves. Reliable [Formula: see text] estimation and stable inverse [Formula: see text] filtering are expected to improve the resolution of seismic data and deep-layer energy. Many methods of estimating [Formula: see text] are based on an individual wavelet. However, it is difficult to extract the individual wavelet precisely from seismic reflection data. To avoid this problem, we have developed a method of directly estimating [Formula: see text] from reflection data. The core of the methodology is selecting the peak-frequency points to linear fit their logarithmic spectrum and time-frequency product. Then, we calculated [Formula: see text] according to the relationship between [Formula: see text] and the optimized slope. First, to get the peak frequency points at different times, we use the generalized S transform to produce the 2D high-precision time-frequency spectrum. According to the seismic wave attenuation mechanism, the logarithmic spectrum attenuates linearly with the product of frequency and time. Thus, the second step of the method is transforming a 2D spectrum into 1D by variable substitution. In the process of transformation, we only selected the peak frequency points to participate in the fitting process, which can reduce the impact of the interference on the spectrum. Third, we obtain the optimized slope by least-squares fitting. To demonstrate the reliability of our method, we applied it to a constant [Formula: see text] model and the real data of a work area. For the real data, we calculated the [Formula: see text] curve of the seismic trace near a well and we get the high-resolution section by using stable inverse [Formula: see text] filtering. The model and real data indicate that our method is effective and reliable for estimating the [Formula: see text] value.

Potentially Large Subsurface Gas Hydrate Bodies in the Mexican Ridges, Southwestern Gulf of Mexico

2021 ◽  
pp. 1-29
Author(s):  
Papia Nandi ◽  
Patrick Fulton ◽  
James Dale
Keyword(s):  
Gulf Of Mexico ◽  
Gas Hydrate ◽  
Seismic Data ◽  
Poor Quality ◽  
Reflection Point ◽  
Seismic Reflection Data ◽  
Reflection Data ◽  
High Impedance ◽  
Acoustic Velocities ◽  
Seismic Images

As rising ocean temperatures can destabilize gas hydrate, identifying and characterizing large shallow hydrate bodies is increasingly important in order to understand their hazard potential. In the southwestern Gulf of Mexico, reanalysis of 3D seismic reflection data reveals evidence for the presence of six potentially large gas hydrate bodies located at shallow depths below the seafloor. We originally interpreted these bodies as salt, as they share common visual characteristics on seismic data with shallow allochthonous salt bodies, including high-impedance boundaries and homogenous interiors with very little acoustic reflectivity. However, when seismic images are constructed using acoustic velocities associated with salt, the resulting images were of poor quality containing excessive moveout in common reflection point (CRP) offset image gathers. Further investigation reveals that using lower-valued acoustic velocities results in higher quality images with little or no moveout. We believe that these lower acoustic values are representative of gas hydrate and not of salt. Directly underneath these bodies lies a zone of poor reflectivity, which is both typical and expected under hydrate. Observations of gas in a nearby well, other indicators of hydrate in the vicinity, and regional geologic context, all support the interpretation that these large bodies are composed of hydrate. The total equivalent volume of gas within these bodies is estimated to potentially be as large as 1.5 gigatons or 10.5 TCF, considering uncertainty for estimates of porosity and saturation, comparable to the entire proven natural gas reserves of Trinidad and Tobago in 2019.

scholarly journals Improved Interpretation of Deep Seismic Reflection Data in Areas of Complex Geology Through Integration With Passive Seismic Data Sets

2018 ◽  
Vol 123 (12) ◽  
pp. 10,810-10,830
Author(s):  
Michael Dentith ◽  
Huaiyu Yuan ◽  
Ruth Elaine Murdie ◽  
Perla Pina-Varas ◽  
Simon P. Johnson ◽  
...  
Keyword(s):  
Seismic Data ◽  
Seismic Reflection ◽  
Data Sets ◽  
Seismic Reflection Data ◽  
Deep Seismic Reflection ◽  
Reflection Data ◽  
Passive Seismic ◽  
Complex Geology

Late Cretaceous – Cenozoic history of the transition zone between the East European Craton and the Paleozoic Platform, Polish sector of the Baltic Sea, revealed by new offshore regional seismic reflection data (BALTEC project)

2021 ◽  
Author(s):  
Piotr Krzywiec ◽  
Łukasz Słonka ◽  
Quang Nguyen ◽  
Michał Malinowski ◽  
Mateusz Kufrasa ◽  
...  
Keyword(s):  
High Resolution ◽  
Late Cretaceous ◽  
Seismic Data ◽  
Seismic Reflection ◽  
Upper Cretaceous ◽  
Seismic Reflection Data ◽  
East European ◽  
Reflection Data ◽  
Multichannel Seismic Reflection ◽  
Multichannel Seismic Reflection Data

<p>In 2016, approximately 850 km of high-resolution multichannel seismic reflection data of the BALTEC survey have been acquired offshore Poland within the transition zone between the East European Craton and the Paleozoic Platform. Data processing, focused on removal of multiples, strongly overprinting geological information at shallower intervals, included SRME, TAU-P domain deconvolution, high resolution parabolic Radon demultiple and SWDM (Shallow Water De-Multiple). Entire dataset was Kirchhoff pre-stack time migrated. Additionally, legacy shallow high-resolution multichannel seismic reflection data acquired in this zone in 1997 was also used. All this data provided new information on various aspects of the Phanerozoic evolution of this area, including Late Cretaceous to Cenozoic tectonics and sedimentation. This phase of geological evolution could be until now hardly resolved by analysis of industry seismic data as, due to limited shallow seismic imaging and very strong overprint of multiples, essentially no information could have been retrieved from this data for first 200-300 m. Western part of the BALTEC dataset is located above the offshore segment of the Mid-Polish Swell (MPS) – large anticlinorium formed due to inversion of the axial part of the Polish Basin. BALTEC seismic data proved that Late Cretaceous inversion of the Koszalin – Chojnice fault zone located along the NE border of the MPS was thick-skinned in nature and was associated with substantial syn-inversion sedimentation. Subtle thickness variations and progressive unconformities imaged by BALTEC seismic data within the Upper Cretaceous succession in vicinity of the Kamień-Adler and the Trzebiatów fault zones located within the MPS documented complex interplay of Late Cretaceous basin inversion, erosion and re-deposition. Precambrian basement of the Eastern, cratonic part of the study area is overlain by Cambro-Silurian sedimentary cover. It is dissected by a system of steep, mostly reverse faults rooted in most cases in the deep basement. This fault system has been regarded so far as having been formed mostly in Paleozoic times, due to the Caledonian orogeny. As a consequence, Upper Cretaceous succession, locally present in this area, has been vaguely defined as a post-tectonic cover, locally onlapping uplifted Paleozoic blocks. New seismic data, because of its reliable imaging of the shallowest substratum, confirmed that at least some of these deeply-rooted faults were active as a reverse faults in latest Cretaceous – earliest Paleogene. Consequently, it can be unequivocally proved that large offshore blocks of Silurian and older rocks presently located directly beneath the Cenozoic veneer must have been at least partly covered by the Upper Cretaceous succession; then, they were uplifted during the widespread inversion that affected most of Europe. Ensuing regional erosion might have at least partly provided sediments that formed Upper Cretaceous progradational wedges recently imaged within the onshore Baltic Basin by high-end PolandSPAN regional seismic data. New seismic data imaged also Paleogene and younger post-inversion cover. All these results prove that Late Cretaceous tectonics substantially affected large areas located much farther towards the East than previously assumed.</p><p>This study was funded by the Polish National Science Centre (NCN) grant no UMO-2017/27/B/ST10/02316.</p>

scholarly journals Monte Carlo reservoir analysis combining seismic reflection data and informed priors

Geophysics ◽  
2015 ◽  
Vol 80 (1) ◽  
pp. R31-R41 ◽  
Author(s):  
Andrea Zunino ◽  
Klaus Mosegaard ◽  
Katrine Lange ◽  
Yulia Melnikova ◽  
Thomas Mejer Hansen
Keyword(s):  
Monte Carlo ◽  
Seismic Data ◽  
Seismic Reflection ◽  
Probabilistic Approach ◽  
Multiple Point ◽  
Petroleum Reservoir ◽  
Inversion Algorithm ◽  
Reservoir Properties ◽  
Seismic Reflection Data ◽  
Reflection Data

Determination of a petroleum reservoir structure and rock bulk properties relies extensively on inference from reflection seismology. However, classic deterministic methods to invert seismic data for reservoir properties suffer from some limitations, among which are the difficulty of handling complex, possibly nonlinear forward models, and the lack of robust uncertainty estimations. To overcome these limitations, we studied a methodology to invert seismic reflection data in the framework of the probabilistic approach to inverse problems, using a Markov chain Monte Carlo (McMC) algorithm with the goal to directly infer the rock facies and porosity of a target reservoir zone. We thus combined a rock-physics model with seismic data in a single inversion algorithm. For large data sets, the McMC method may become computationally impractical, so we relied on multiple-point-based a priori information to quantify geologically plausible models. We tested this methodology on a synthetic reservoir model. The solution of the inverse problem was then represented by a collection of facies and porosity reservoir models, which were samples of the posterior distribution. The final product included probability maps of the reservoir properties in obtained by performing statistical analysis on the collection of solutions.

Using instantaneous frequency and colored inversion attributes to distinguish and determine the sandstones facies of the Late Ordovician Mamuniyat reservoir, R-field in Murzuq Basin, Libya

2016 ◽  
Vol 4 (4) ◽  
pp. T507-T519 ◽  
Author(s):  
Yousf Abushalah ◽  
Laura Serpa
Keyword(s):  
Instantaneous Frequency ◽  
Seismic Data ◽  
Acoustic Impedance ◽  
Rock Physics ◽  
Side Lobe ◽  
Petroleum Reservoir ◽  
Seismic Reflection Data ◽  
Frequency Bands ◽  
Reflection Data ◽  
Sandstone Facies

The Mamuniyat petroleum reservoir in southwestern Libya is comprised of clean sandstones and intercalated shale and sand facies that are characterized by spatial porosity variations. Seismic reflection data from the field exhibit relatively low vertical seismic resolution, side lobes of reflection wavelets, reflection interference, and low acoustic impedance contrast between the reservoir and the units underneath the reservoir, which make mapping those facies a difficult task. In the absence of broadband seismic data, optimizing frequency bands of bandlimited data can be used to suppress pseudoreflectors resulting from side-lobe effects and help to separate the clean sandstone facies of the reservoir. We have optimized the data based on our investigation of seismic frequency bands and used instantaneous frequency analysis to reveal the reflection discontinuity that is mainly associated with the reservoir boundary of the sandstone facies of the clean Mamuniyat reservoir. We also preformed rock-physics diagnostic modeling and inverted the seismic data using spectral-based colored inversion into relative acoustic impedance. The inverted impedance matches the up-scaled impedance from the well data and the inversion of relative acoustic impedance confirms the conclusion that was drawn from the instantaneous frequency results. The interpretation of facies distributions based on the instantaneous frequency was supported by the inversion results and the rock-physics models.

Seismic evidence for the migration of fluids within the accretionary complex of western Canada

1991 ◽  
Vol 28 (4) ◽  
pp. 542-556 ◽  
Author(s):  
A. J. Calvert ◽  
R. M. Clowes
Keyword(s):  
Continental Slope ◽  
Seismic Data ◽  
Accretionary Prism ◽  
Western Canada ◽  
Accretionary Wedge ◽  
Seismic Velocities ◽  
Seismic Reflection Data ◽  
Reflection Data ◽  
Subducting Plate ◽  
Important Evidence

Multichannel deep seismic reflection data from the subduction zone of western Canada delineate the wedge of accereted sediments and the principal terranes (Crescent, Pacific Rim, and Wrangellia) that form the convergent margin. The top of the igneous oceanic crust is defined by subhorizontal reflections extending at least 100 km landward of the deformation front. Upon incorporation into the accretionary wedge, the clearly defined stratigraphy of the incoming oceanic sedimentary section is destroyed over a distance of about 10 km. Initially, an unreflective zone, which correlates well with maximum fluid expulsion, is formed. Farther landward, a predominantly landward-dipping reflectivity exists. A number of reflections are thrust faults, which appear to merge at depth with the subhorizontal reflections, but most have another origin. These reflections may be related to the movement of fluids generated by the compaction of sediments or possibly by the dehydration of the subducting plate. They are strongest in a region of depressed seismic velocities beneath the continental slope, where an analysis of reflection amplitude with offset implies that a high Poisson's ratio exists; this is consistent with the presence of elevated pore pressures. Thus, pore pressure variations associated with the migration of fluids may be the cause of much of the reflectivity within the accreted wedge, although the precipitation of minerals from rising fluids could also be important. Evidence from the seismic data also indicates that fluids from the accretionary prism are being expelled into the sediments of the overlying Tofino basin. A number of anomalously strong reflections and disruption of the horizontally stratified sediments within the lower levels of the basin probably represent fluids that migrated upward from the accreted wedge and were trapped against impermeable barriers created through the deposition of sediments on the continental slope and in the basin.

Amplitude preservation of Radon-based multiple-removal filters

Geophysics ◽  
2006 ◽  
Vol 71 (5) ◽  
pp. V123-V126 ◽  
Author(s):  
Ethan J. Nowak ◽  
Matthias G. Imhof
Keyword(s):  
Radon Transform ◽  
Seismic Data ◽  
Transform Domain ◽  
Multiple Reflections ◽  
Avo Analysis ◽  
Amplitude Versus Offset ◽  
Amplitude Preservation ◽  
Amplitude Versus

This study examines the effect of filtering in the Radon transform domain on reflection amplitudes. Radon filters are often used for removal of multiple reflections from normal moveout-corrected seismic data. The unweighted solution to the Radon transform reduces reflection amplitudes at both near and far offsets due to a truncation effect. However, the weighted solutions to the transform produce localized events in the transform domain, which minimizes this truncation effect. Synthetic examples suggest that filters designed in the Radon domain based on a weighted solution to the linear, parabolic, or hyperbolic transforms preserve the near- and far-offset reflection amplitudes while removing the multiples; whereas the unweighted solutions diminish reflection amplitudes which may distort subsequent amplitude-versus-offset (AVO) analysis.

Sign in / Sign up

Export Citation Format

Share Document