A generalized form of Snell’s law in anisotropic media

Geophysics ◽  
2000 ◽  
Vol 65 (2) ◽  
pp. 632-637 ◽  
Author(s):  
Michael A. Slawinski ◽  
Raphaël A. Slawinski ◽  
R. James Brown ◽  
John M. Parkin

We have reformulated the law governing the refraction of rays at a planar interface separating two anisotropic media in terms of slowness surfaces. Equations connecting ray directions and phase‐slowness angles are derived using geometrical properties of the gradient operator in slowness space. A numerical example shows that, even in weakly anisotropic media, the ray trajectory governed by the anisotropic Snell’s law is significantly different from that obtained using the isotropic form. This could have important implications for such considerations as imaging (e.g., migration) and lithology analysis (e.g., amplitude variation with offset). Expressions are shown specifically for compressional (qP) waves but they can easily be extended to SH waves by equating the anisotropic parameters (i.e., ε = δ ⇒ γ) and to qSV and converted waves by similar means. The analytic expressions presented are more complicated than the standard form of Snell’s law. To facilitate practical application, we include our Mathematica code.

1997 ◽  
Author(s):  
Michael A. Slawinski ◽  
Raphael A. Slawinski ◽  
John M. Parkin

Geophysics ◽  
2009 ◽  
Vol 74 (5) ◽  
pp. WB147-WB152 ◽  
Author(s):  
Claudia Vanelle ◽  
Dirk Gajewski

Snell’s law describes the relationship between phase angles and velocities during the reflection or transmission of waves. It states that horizontal slowness with respect to an interface is preserved during reflection or transmission. Evaluation of this relationship at an interface between two isotropic media is straightforward. For anisotropic media, it is a complicated problem because phase velocity depends on the angle; in the anisotropic reflection/transmission problem, neither is known. Solving Snell’s law in the anisotropic case requires a numerical solution for a sixth-order polynomial. In addition to finding the roots, they must be assigned to the correct reflected or transmitted wave type. We show that if the anisotropy is weak, an approximate solution based on first-order perturbation theory can be obtained. This approach permits the computation of the full slowness vector and, thereby, the phase velocity and angle. In addition to replacing the need for solving the sixth-order polynomial, the resulting expressions allow us to prescribe the desired reflected or transmitted wave type. The method is best implemented iteratively to increase accuracy. The result can be applied to anisotropic media with arbitrary symmetry. It converges toward the weak-anisotropy solution and provides overall good accuracy for media with weak to moderate anisotropy.


Geophysics ◽  
1991 ◽  
Vol 56 (10) ◽  
pp. 1596-1602 ◽  
Author(s):  
Patricia A. Berge

Conventional seismic experiments can record converted shear waves in anisotropic media, but the shear‐wave stacking velocities pose a problem when processing and interpreting the data. Methods used to find shear‐wave stacking velocities in isotropic media will not always provide good estimates in anisotropic media. Although isotropic methods often can be used to estimate shear‐wave stacking velocities in transversely isotropic media with vertical symmetry axes, the estimations fail for some transversely isotropic media even though the anisotropy is weak. For a given anisotropic medium, the shear‐wave stacking velocity can be estimated using isotropic methods if the isotropic Snell’s law approximates the anisotropic Snell’s law and if the shear wavefront is smooth enough near the vertical axis to be fit with an ellipse. Most of the 15 transversely isotropic media examined in this paper met these conditions for short reflection spreads and small ray angles. Any transversely isotropic medium will meet these conditions if the transverse isotropy is weak and caused by thin subhorizontal layering. For three of the media examined, the anisotropy was weak but the shear wave-fronts were not even approximately elliptical near the vertical axis. Thus, isotropic methods provided poor estimates of the shear‐wave stacking velocities. These results confirm that for any given transversely isotropic medium, it is possible to determine whether or not shear‐wave stacking velocities can be estimated using isotropic velocity analysis.


1993 ◽  
Vol 47 (3) ◽  
pp. 338-340 ◽  
Author(s):  
Takeshi Hasegawa ◽  
Junzo Umemura ◽  
Tohru Takenaka

In anisotropic media, there exist ordinary and extraordinary rays. Until now, there has been no simple refraction law like Snell's law for the extraordinary ray. In this study, with the Fresnel model, we made a simple refraction law applicable to both ordinary and extraordinary rays, though it is limited for uniaxial media. The obtained formula could explain the differences between the two rays and would be very useful in extending the traditional isotropic electromagnetic theories to the uniaxial anisotropic electromagnetic theories.


2020 ◽  
Vol 116 (11) ◽  
pp. 112402 ◽  
Author(s):  
Tomosato Hioki ◽  
Rei Tsuboi ◽  
Tom H. Johansen ◽  
Yusuke Hashimoto ◽  
Eiji Saitoh

Geophysics ◽  
2012 ◽  
Vol 77 (6) ◽  
pp. B295-B306 ◽  
Author(s):  
Alexander Duxbury ◽  
Don White ◽  
Claire Samson ◽  
Stephen A. Hall ◽  
James Wookey ◽  
...  

Cap rock integrity is an essential characteristic of any reservoir to be used for long-term [Formula: see text] storage. Seismic AVOA (amplitude variation with offset and azimuth) techniques have been applied to map HTI anisotropy near the cap rock of the Weyburn field in southeast Saskatchewan, Canada, with the purpose of identifying potential fracture zones that may compromise seal integrity. This analysis, supported by modeling, observes the top of the regional seal (Watrous Formation) to have low levels of HTI anisotropy, whereas the reservoir cap rock (composite Midale Evaporite and Ratcliffe Beds) contains isolated areas of high intensity anisotropy, which may be fracture-related. Properties of the fracture fill and hydraulic conductivity within the inferred fracture zones are not constrained using this technique. The predominant orientations of the observed anisotropy are parallel and normal to the direction of maximum horizontal stress (northeast–southwest) and agree closely with previous fracture studies on core samples from the reservoir. Anisotropy anomalies are observed to correlate spatially with salt dissolution structures in the cap rock and overlying horizons as interpreted from 3D seismic cross sections.


2016 ◽  
Vol 65 (3) ◽  
pp. 736-746 ◽  
Author(s):  
Chao Xu ◽  
Jianxin Wei ◽  
Bangrang Di

Sign in / Sign up

Export Citation Format

Share Document