Seismic detection and characterization of a man-made karst analog — A feasibility study

Geophysics ◽  
2021 ◽  
Vol 86 (3) ◽  
pp. WB35-WB48
Author(s):  
Roland Gritto ◽  
Ali Elobaid Elnaiem ◽  
Fateh Alrahman Mohamed ◽  
Fadhil Sadooni

At the site of a water drainage shaft on the campus of Qatar University that serves as a man-made karst analog, two seismic imaging techniques were adapted to use resonant scattered waves recorded during active-source seismic surveys and during passive ambient-noise surveys. Data acquisition included two seismic transmission surveys that encompassed the shaft and a passive ambient-noise survey that extended across the top of the shaft. Seismic imaging of band-pass-filtered resonance waves correctly estimated the location and dimension of the shaft. Furthermore, the method detected the presence and the location of a horizontal drainage pipe and gravel bed connecting neighboring water shafts. Ambient-noise data were analyzed by computing amplitude values of the seismic records in spectral passbands. The results indicated an amplification of seismic amplitudes above the shaft for low-frequency passbands and a sharp decrease in amplitude values for high-frequency passbands. The high- and low-amplitude values displayed as a function of the receiver position allowed for accurate detection and location of the shaft in space. Ground truthing of the imaging results confirmed the accuracy of the seismic techniques, whereas numerical modeling supported the interpretation of the ambient-noise data. The techniques used do not require knowledge of the seismic velocities in the subsurface, but they depend on a priori information about the approximate location of the target.

2020 ◽  
Author(s):  
Yesenia Martínez ◽  
Juan Alcalde ◽  
David Martí ◽  
Puy Ayarza ◽  
Mario Ruiz ◽  
...  

<p>In order to tackle the ever-increasing demand of raw materials, the European Institute of Technology (EIT) promotes research and innovation solutions for safe and sustainable mineral exploration through its Raw Materials Programme. The SIT4ME project (“Seismic Imaging Techniques for Mineral Exploration”) has been funded as part of this program to develop efficient techniques in seismic acquisition and imaging methods for mineral exploration in crystalline environments. Within SIT4ME, a multidisciplinary data acquisition experiment (i.e. 3D-3C active and passive source seismic datasets) took place in November 2009 in Sotiel-Coronada (Iberian Pyrite Belt, SW Spain). The aim of this experiment was to image a 300-500 m depth pyrite-rich massive sulfide orebody interbedded with felsic volcanic rocks and shales. The seismic dataset involves the recording of 875 vibration points in 653 seismic receivers, distributed in a 3D mesh around the target and six 2D crooked lines. Conventional processing workflow (such as static corrections, surface-consistent deconvolution, amplitude equalization, frequency filtering, and velocity analysis) was combined with more advance methods (e.g. ground roll attenuation or post-stack coherency filtering) to obtain robust images of the subsurface of the target area. The processing workflow has been applied to four 2D seismic sections, one in the North-South and three in the East-West directions, distributed across the study area. The preliminary imaging results show coherent reflective packages down to two seconds two-way traveltime (TWT). The North-South line contains a north-dipping ~400 m long highly reflective zone in the center at 130 ms TWT. The east-west profiles show a slightly folded structure (antiform and synform) which is evident down to 0.25 s TWT. Towards the north, the seismic lines become parallel to subsurface structures and therefore the track of these structures is lost. Current work involves the incorporation of well-log data to improve the quality and resolution of the interpretations. The next processing steps will involve pre-stack depth migration, P-wave travel-time tomography and a combined analysis of controlled source imaging and ambient noise interferometry data.</p><p>The SIT4ME project has been funded by EIT Raw Materials (17024).</p>


2022 ◽  
Author(s):  
◽  
Weiwei Wang

<p><b>This thesis uses continuous ambient noise data recorded by Ocean Bottom Seismometers (OBSs) to study seismic velocities in the upper crust of the overriding plate. The first and second projects (Chapters 3 and 4) focus on temporal seismic velocity variations in the northern Hikurangi subduction zone offshore the North Island, New Zealand, while the third project (Chapter 5) focuses on shear wave velocities in the southwestern Okinawa Trough offshore northeastern Taiwan. In the first project (Chapters 3), we investigate a region of frequent slow slip events (SSEs) offshore Gisborne, North Island, New Zealand. From September to October 2014, an SSE occurred with a slip over 250 mm and was recorded successfully by the Hikurangi Ocean Bottom Investigation of Tremor and Slow Slip deployment II (HOBITSS II). We apply coda wave interferometry on the ambient noise data acquired by nine OBSs deployed by the HOBITSS II to study the seismic velocity variations related to the SSE. The average velocity variations display a decrease on the order of 0.05% during the SSE, followed by an increase of similar magnitude afterwards. Two hypotheses are proposed to explain our observation. The first hypothesis, which has been suggested by previous studies, considers that the velocity decrease during the SSE is caused by more fluids migrating into the upper plate as the SSE breaks a low-permeability seal on the plate boundary. After the SSE, the fluids in the upper plate diffuse gradually and the velocity increases; The second hypothesis is that before the SSE, elastic strain accumulates causing contraction and reduction of porosity and therefore increase of velocity (the velocity increase between SSEs). During the SSE, the velocity decrease is caused by increased porosity as the SSE relieves the accumulated elastic strain on the plate interface, which results in dilation. After the SSE, stress and strain accumulate again, causing a porosity decrease and a velocity increase back to the original value. This study demonstrates that the velocity variations related to SSEs are observable and provides evidence for slow slip mechanism hypotheses.</b></p> <p>The second project (Chapter 4) focuses on the temporal seismic velocity variations associated with an SSE in 2019 offshore Gisborne, North Island, New Zealand. This is a later SSE in the same area as the first project (Chapters 3). Based on the success of the HOBITSS II, more ocean bottom instruments were deployed in the northern Hikurangi subduction zone from 2018 to 2019 (HOBITSS V). An SSE lasting approximately one month from the end of March to the beginning of May 2019 occurred during the deployment and was recorded by the network. The main slip was south of the deployment and the slip beneath the deployment was up to 150 mm. This study applies coda wave interferometry on the ambient noise data acquired by five OBSs and computes seismic velocity variations to investigate their relation to the SSE. A velocity decrease on the order of 0.015% during the SSE and an increase back to the original velocity value are observed at 1–2.5 s. This supports the two hypotheses proposed in Chapters 3: fluid migration and/or stain changes through the SSE cycle. In addition, velocity variations computed from individual stations show velocity increases before the SSE, which are destructively interfered in their average. Such a situation could occur if the SSE migrated across the network. If the velocity increases before the SSE from individual stations are real, they can be only explained by the hypothesis of crustal strain changes (the second hypothesis in project 1). However, fluid migration (the first hypothesis in project 1) may still happen concomitantly.</p> <p>The third project focuses on the tectonics in southwestern Okinawa Trough offshore northeastern Taiwan. The southwestern Okinawa Trough is an active back-arc basin, extending and rifting within the continental lithosphere. The tectonic development of the back-arc basin is still not well-understood. This study uses continuous ambient noise data recorded by 34 OBSs deployed by Academia Sinica at various periods from 2010 to 2018. Cross-correlations on vertical seismic components and pressure gauges are computed to construct Rayleigh/Scholte waves to study the shear wave velocity structure in the southwestern Okinawa Trough. Phase velocities are measured from the Rayleigh/Scholte waves. Shear velocities are inverted from the phase velocities. Results show the velocity in the south of the back-arc rifting axis near the axis is slower than the velocity in the north of the rifting axis, suggesting the velocity structure in the southwestern Okinawa Trough is asymmetric along the rifting axis. Previous studies have shown high heat flows (about 110mW/m 2 on average) in the south of the rifting axis. The low velocity in the south could be caused by the high heat flow that may be related to asymmetric back-arc extension and/or rifting. This study presents the shear wave velocity structure in the southwest Okinawa Trough is asymmetric along the rifting axis, which implies the back-arc extending/rifting is asymmetric in the study region. This study also suggests effective techniques for OBS noise corrections and unwrapping the cycle skipping of phase velocity measurements.</p> <p>In summary, this thesis represents three projects focusing on seismic velocities in two subduction zones using ambient noise data collected by OBSs. The first and second projects study the temporal velocity variations and the relation to SSEs. Both studies observe velocity decreases during the SSEs and increases after the SSEs, supporting two hypotheses of fluid migration and/or stain changes through the SSE cycle. The third project finds the shear velocity structure in the southwestern Okinawa Trough is asymmetric along the rifting center, which may imply the back-arc extension is asymmetric.</p>


2022 ◽  
Author(s):  
◽  
Weiwei Wang

<p><b>This thesis uses continuous ambient noise data recorded by Ocean Bottom Seismometers (OBSs) to study seismic velocities in the upper crust of the overriding plate. The first and second projects (Chapters 3 and 4) focus on temporal seismic velocity variations in the northern Hikurangi subduction zone offshore the North Island, New Zealand, while the third project (Chapter 5) focuses on shear wave velocities in the southwestern Okinawa Trough offshore northeastern Taiwan. In the first project (Chapters 3), we investigate a region of frequent slow slip events (SSEs) offshore Gisborne, North Island, New Zealand. From September to October 2014, an SSE occurred with a slip over 250 mm and was recorded successfully by the Hikurangi Ocean Bottom Investigation of Tremor and Slow Slip deployment II (HOBITSS II). We apply coda wave interferometry on the ambient noise data acquired by nine OBSs deployed by the HOBITSS II to study the seismic velocity variations related to the SSE. The average velocity variations display a decrease on the order of 0.05% during the SSE, followed by an increase of similar magnitude afterwards. Two hypotheses are proposed to explain our observation. The first hypothesis, which has been suggested by previous studies, considers that the velocity decrease during the SSE is caused by more fluids migrating into the upper plate as the SSE breaks a low-permeability seal on the plate boundary. After the SSE, the fluids in the upper plate diffuse gradually and the velocity increases; The second hypothesis is that before the SSE, elastic strain accumulates causing contraction and reduction of porosity and therefore increase of velocity (the velocity increase between SSEs). During the SSE, the velocity decrease is caused by increased porosity as the SSE relieves the accumulated elastic strain on the plate interface, which results in dilation. After the SSE, stress and strain accumulate again, causing a porosity decrease and a velocity increase back to the original value. This study demonstrates that the velocity variations related to SSEs are observable and provides evidence for slow slip mechanism hypotheses.</b></p> <p>The second project (Chapter 4) focuses on the temporal seismic velocity variations associated with an SSE in 2019 offshore Gisborne, North Island, New Zealand. This is a later SSE in the same area as the first project (Chapters 3). Based on the success of the HOBITSS II, more ocean bottom instruments were deployed in the northern Hikurangi subduction zone from 2018 to 2019 (HOBITSS V). An SSE lasting approximately one month from the end of March to the beginning of May 2019 occurred during the deployment and was recorded by the network. The main slip was south of the deployment and the slip beneath the deployment was up to 150 mm. This study applies coda wave interferometry on the ambient noise data acquired by five OBSs and computes seismic velocity variations to investigate their relation to the SSE. A velocity decrease on the order of 0.015% during the SSE and an increase back to the original velocity value are observed at 1–2.5 s. This supports the two hypotheses proposed in Chapters 3: fluid migration and/or stain changes through the SSE cycle. In addition, velocity variations computed from individual stations show velocity increases before the SSE, which are destructively interfered in their average. Such a situation could occur if the SSE migrated across the network. If the velocity increases before the SSE from individual stations are real, they can be only explained by the hypothesis of crustal strain changes (the second hypothesis in project 1). However, fluid migration (the first hypothesis in project 1) may still happen concomitantly.</p> <p>The third project focuses on the tectonics in southwestern Okinawa Trough offshore northeastern Taiwan. The southwestern Okinawa Trough is an active back-arc basin, extending and rifting within the continental lithosphere. The tectonic development of the back-arc basin is still not well-understood. This study uses continuous ambient noise data recorded by 34 OBSs deployed by Academia Sinica at various periods from 2010 to 2018. Cross-correlations on vertical seismic components and pressure gauges are computed to construct Rayleigh/Scholte waves to study the shear wave velocity structure in the southwestern Okinawa Trough. Phase velocities are measured from the Rayleigh/Scholte waves. Shear velocities are inverted from the phase velocities. Results show the velocity in the south of the back-arc rifting axis near the axis is slower than the velocity in the north of the rifting axis, suggesting the velocity structure in the southwestern Okinawa Trough is asymmetric along the rifting axis. Previous studies have shown high heat flows (about 110mW/m 2 on average) in the south of the rifting axis. The low velocity in the south could be caused by the high heat flow that may be related to asymmetric back-arc extension and/or rifting. This study presents the shear wave velocity structure in the southwest Okinawa Trough is asymmetric along the rifting axis, which implies the back-arc extending/rifting is asymmetric in the study region. This study also suggests effective techniques for OBS noise corrections and unwrapping the cycle skipping of phase velocity measurements.</p> <p>In summary, this thesis represents three projects focusing on seismic velocities in two subduction zones using ambient noise data collected by OBSs. The first and second projects study the temporal velocity variations and the relation to SSEs. Both studies observe velocity decreases during the SSEs and increases after the SSEs, supporting two hypotheses of fluid migration and/or stain changes through the SSE cycle. The third project finds the shear velocity structure in the southwestern Okinawa Trough is asymmetric along the rifting center, which may imply the back-arc extension is asymmetric.</p>


2022 ◽  
Author(s):  
◽  
Weiwei Wang

<p><b>This thesis uses continuous ambient noise data recorded by Ocean Bottom Seismometers (OBSs) to study seismic velocities in the upper crust of the overriding plate. The first and second projects (Chapters 3 and 4) focus on temporal seismic velocity variations in the northern Hikurangi subduction zone offshore the North Island, New Zealand, while the third project (Chapter 5) focuses on shear wave velocities in the southwestern Okinawa Trough offshore northeastern Taiwan. In the first project (Chapters 3), we investigate a region of frequent slow slip events (SSEs) offshore Gisborne, North Island, New Zealand. From September to October 2014, an SSE occurred with a slip over 250 mm and was recorded successfully by the Hikurangi Ocean Bottom Investigation of Tremor and Slow Slip deployment II (HOBITSS II). We apply coda wave interferometry on the ambient noise data acquired by nine OBSs deployed by the HOBITSS II to study the seismic velocity variations related to the SSE. The average velocity variations display a decrease on the order of 0.05% during the SSE, followed by an increase of similar magnitude afterwards. Two hypotheses are proposed to explain our observation. The first hypothesis, which has been suggested by previous studies, considers that the velocity decrease during the SSE is caused by more fluids migrating into the upper plate as the SSE breaks a low-permeability seal on the plate boundary. After the SSE, the fluids in the upper plate diffuse gradually and the velocity increases; The second hypothesis is that before the SSE, elastic strain accumulates causing contraction and reduction of porosity and therefore increase of velocity (the velocity increase between SSEs). During the SSE, the velocity decrease is caused by increased porosity as the SSE relieves the accumulated elastic strain on the plate interface, which results in dilation. After the SSE, stress and strain accumulate again, causing a porosity decrease and a velocity increase back to the original value. This study demonstrates that the velocity variations related to SSEs are observable and provides evidence for slow slip mechanism hypotheses.</b></p> <p>The second project (Chapter 4) focuses on the temporal seismic velocity variations associated with an SSE in 2019 offshore Gisborne, North Island, New Zealand. This is a later SSE in the same area as the first project (Chapters 3). Based on the success of the HOBITSS II, more ocean bottom instruments were deployed in the northern Hikurangi subduction zone from 2018 to 2019 (HOBITSS V). An SSE lasting approximately one month from the end of March to the beginning of May 2019 occurred during the deployment and was recorded by the network. The main slip was south of the deployment and the slip beneath the deployment was up to 150 mm. This study applies coda wave interferometry on the ambient noise data acquired by five OBSs and computes seismic velocity variations to investigate their relation to the SSE. A velocity decrease on the order of 0.015% during the SSE and an increase back to the original velocity value are observed at 1–2.5 s. This supports the two hypotheses proposed in Chapters 3: fluid migration and/or stain changes through the SSE cycle. In addition, velocity variations computed from individual stations show velocity increases before the SSE, which are destructively interfered in their average. Such a situation could occur if the SSE migrated across the network. If the velocity increases before the SSE from individual stations are real, they can be only explained by the hypothesis of crustal strain changes (the second hypothesis in project 1). However, fluid migration (the first hypothesis in project 1) may still happen concomitantly.</p> <p>The third project focuses on the tectonics in southwestern Okinawa Trough offshore northeastern Taiwan. The southwestern Okinawa Trough is an active back-arc basin, extending and rifting within the continental lithosphere. The tectonic development of the back-arc basin is still not well-understood. This study uses continuous ambient noise data recorded by 34 OBSs deployed by Academia Sinica at various periods from 2010 to 2018. Cross-correlations on vertical seismic components and pressure gauges are computed to construct Rayleigh/Scholte waves to study the shear wave velocity structure in the southwestern Okinawa Trough. Phase velocities are measured from the Rayleigh/Scholte waves. Shear velocities are inverted from the phase velocities. Results show the velocity in the south of the back-arc rifting axis near the axis is slower than the velocity in the north of the rifting axis, suggesting the velocity structure in the southwestern Okinawa Trough is asymmetric along the rifting axis. Previous studies have shown high heat flows (about 110mW/m 2 on average) in the south of the rifting axis. The low velocity in the south could be caused by the high heat flow that may be related to asymmetric back-arc extension and/or rifting. This study presents the shear wave velocity structure in the southwest Okinawa Trough is asymmetric along the rifting axis, which implies the back-arc extending/rifting is asymmetric in the study region. This study also suggests effective techniques for OBS noise corrections and unwrapping the cycle skipping of phase velocity measurements.</p> <p>In summary, this thesis represents three projects focusing on seismic velocities in two subduction zones using ambient noise data collected by OBSs. The first and second projects study the temporal velocity variations and the relation to SSEs. Both studies observe velocity decreases during the SSEs and increases after the SSEs, supporting two hypotheses of fluid migration and/or stain changes through the SSE cycle. The third project finds the shear velocity structure in the southwestern Okinawa Trough is asymmetric along the rifting center, which may imply the back-arc extension is asymmetric.</p>


Geophysics ◽  
2012 ◽  
Vol 77 (5) ◽  
pp. WC59-WC68 ◽  
Author(s):  
Deanne Duff ◽  
Charles Hurich ◽  
Sharon Deemer

Seismic methods offer significant potential advantages for minerals exploration over more traditional geophysical techniques because of the comparatively high resolution of seismic imaging. This is particularly true as minerals exploration is required to explore deeper to find resources. However, adaptation of seismic imaging techniques to the complex crystalline targets common in the mining environment requires a thorough understanding of the physical properties of the specific combination of ore and host rocks under consideration to choose an appropriate imaging technique. Analysis of the sulfide ores and associated host rocks from the Voisey’s Bay nickel-copper-cobalt deposit indicates that in the pyrrohotite-pentlandite-rich but pyrite-poor assemblage at Voisey’s Bay, seismic velocities are significantly lower ([Formula: see text]) than either the felsic or mafic host rocks ([Formula: see text] and [Formula: see text]). This observation is in contrast with pyrite-rich massive sulfide ores that have velocities that are significantly higher than typical host rocks. The large velocity contrast between the Voisey’s Bay ores and their host rocks makes them good targets for tomographic imaging. However, due to the trade-off between the low velocities and high densities of the Voisey’s Bay sulfides, acoustic impedance contrasts can be quite modest making them less attractive for seismic reflection imaging. Detailed analysis of two different mineralized zones at Voisey’s Bay further demonstrated that, depending on the limiting signal-to-noise ratio, the choice of an effective seismic imaging technique is not universal across a mineral deposit and may be affected by subtle variations in sulfide mineralogy and by the structural/magmatic setting. Our analysis clearly indicated that knowledge of physical properties and geologic setting is critical to the choice of which seismic technique to apply in a given exploration setting.


2015 ◽  
Author(s):  
Rabah Bensalem* ◽  
Djamal Machane ◽  
Jean-Luc Chatelain ◽  
Mohamed Djeddi ◽  
Hakim Moulouel ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document