Multi-parameter model building for the Qiuyue structure using four-component ocean-bottom seismometer data

Geophysics ◽  
2021 ◽  
pp. 1-52
Author(s):  
Yuzhu Liu ◽  
Xinquan Huang ◽  
Jizhong Yang ◽  
Xueyi Liu ◽  
Bin Li ◽  
...  
Keyword(s):  
Wave Velocity ◽  
Waveform Inversion ◽  
Velocity Model ◽  
P Wave ◽  
Velocity Analysis ◽  
Full Waveform Inversion ◽  
Ocean Bottom ◽  
Ocean Bottom Seismometer ◽  
Full Waveform ◽  
P Wave Velocity

Thin sand-mud-coal interbedded layers and multiples caused by shallow water pose great challenges to conventional 3D multi-channel seismic techniques used to detect the deeply buried reservoirs in the Qiuyue field. In 2017, a dense ocean-bottom seismometer (OBS) acquisition program acquired a four-component dataset in East China Sea. To delineate the deep reservoir structures in the Qiuyue field, we applied a full-waveform inversion (FWI) workflow to this dense four-component OBS dataset. After preprocessing, including receiver geometry correction, moveout correction, component rotation, and energy transformation from 3D to 2D, a preconditioned first-arrival traveltime tomography based on an improved scattering integral algorithm is applied to construct an initial P-wave velocity model. To eliminate the influence of the wavelet estimation process, a convolutional-wavefield-based objective function for the preprocessed hydrophone component is used during acoustic FWI. By inverting the waveforms associated with early arrivals, a relatively high-resolution underground P-wave velocity model is obtained, with updates at 2.0 km and 4.7 km depth. Initial S-wave velocity and density models are then constructed based on their prior relationships to the P-wave velocity, accompanied by a reciprocal source-independent elastic full-waveform inversion to refine both velocity models. Compared to a traditional workflow, guided by stacking velocity analysis or migration velocity analysis, and using only the pressure component or other single-component, the workflow presented in this study represents a good approach for inverting the four-component OBS dataset to characterize sub-seafloor velocity structures.

scholarly journals Addressing viscous effects in acoustic full-waveform inversion

Geophysics ◽  
2018 ◽  
Vol 83 (6) ◽  
pp. R611-R628 ◽  
Author(s):  
Òscar Calderón Agudo ◽  
Nuno Vieira da Silva ◽  
Michael Warner ◽  
Tatiana Kalinicheva ◽  
Joanna Morgan
Keyword(s):  
Wave Velocity ◽  
Waveform Inversion ◽  
Velocity Model ◽  
P Wave ◽  
Full Waveform Inversion ◽  
Viscous Effects ◽  
Approximate Estimate ◽  
Intrinsic Attenuation ◽  
Full Waveform ◽  
P Wave Velocity

In conventional full-waveform inversion (FWI), viscous effects are typically neglected, and this is likely to adversely affect the recovery of P-wave velocity. We have developed a strategy to mitigate viscous effects based on the use of matching filters with the aim of improving the performance of acoustic FWI. The approach requires an approximate estimate of the intrinsic attenuation model, and it is one to three times more expensive than conventional acoustic FWI. First, we perform 2D synthetic tests to study the impact of viscoacoustic effects on the recorded wavefield and analyze how that affects the recovered velocity models after acoustic FWI. Then, we apply the current method on the generated data and determine that it mitigates viscous effects successfully even in the presence of noise. We find that having an approximate estimate for intrinsic attenuation, even when these effects are strong, leads to improvements in resolution and a more accurate recovery of the P-wave velocity. Then, we implement and develop our method on a 2D field data set using Gabor transforms to obtain an approximate intrinsic attenuation model and inversion frequencies of up to 24 Hz. The analysis of the results indicates that there is an improvement in terms of resolution and continuity of the layers on the recovered P-wave velocity model, leading to an improved flattening of gathers and a closer match of the inverted velocity model with the migrated seismic data.

scholarly journals Semiglobal viscoacoustic full-waveform inversion

Geophysics ◽  
2019 ◽  
Vol 84 (2) ◽  
pp. R271-R293 ◽  
Author(s):  
Nuno V. da Silva ◽  
Gang Yao ◽  
Michael Warner
Keyword(s):  
Physical Properties ◽  
Wave Velocity ◽  
Seismic Data ◽  
Waveform Inversion ◽  
P Wave ◽  
Full Waveform Inversion ◽  
Data Set ◽  
Intrinsic Attenuation ◽  
Full Waveform ◽  
P Wave Velocity

Full-waveform inversion deals with estimating physical properties of the earth’s subsurface by matching simulated to recorded seismic data. Intrinsic attenuation in the medium leads to the dispersion of propagating waves and the absorption of energy — media with this type of rheology are not perfectly elastic. Accounting for that effect is necessary to simulate wave propagation in realistic geologic media, leading to the need to estimate intrinsic attenuation from the seismic data. That increases the complexity of the constitutive laws leading to additional issues related to the ill-posed nature of the inverse problem. In particular, the joint estimation of several physical properties increases the null space of the parameter space, leading to a larger domain of ambiguity and increasing the number of different models that can equally well explain the data. We have evaluated a method for the joint inversion of velocity and intrinsic attenuation using semiglobal inversion; this combines quantum particle-swarm optimization for the estimation of the intrinsic attenuation with nested gradient-descent iterations for the estimation of the P-wave velocity. This approach takes advantage of the fact that some physical properties, and in particular the intrinsic attenuation, can be represented using a reduced basis, substantially decreasing the dimension of the search space. We determine the feasibility of the method and its robustness to ambiguity with 2D synthetic examples. The 3D inversion of a field data set for a geologic medium with transversely isotropic anisotropy in velocity indicates the feasibility of the method for inverting large-scale real seismic data and improving the data fitting. The principal benefits of the semiglobal multiparameter inversion are the recovery of the intrinsic attenuation from the data and the recovery of the true undispersed infinite-frequency P-wave velocity, while mitigating ambiguity between the estimated parameters.

Seismic characterization of submarine gas-hydrate deposits in the Western Black Sea by acoustic full-waveform inversion of ocean-bottom seismic data

Geophysics ◽  
2019 ◽  
Vol 84 (5) ◽  
pp. B311-B324 ◽  
Author(s):  
Laura Gassner ◽  
Tobias Gerach ◽  
Thomas Hertweck ◽  
Thomas Bohlen
Keyword(s):  
Wave Velocity ◽  
Black Sea ◽  
Gas Hydrate ◽  
Seismic Data ◽  
Field Data ◽  
Waveform Inversion ◽  
P Wave ◽  
Full Waveform Inversion ◽  
Ocean Bottom ◽  
Full Waveform

Evidence for gas-hydrate occurrence in the Western Black Sea is found from seismic measurements revealing bottom-simulating reflectors (BSRs) of varying distinctness. From an ocean-bottom seismic data set, low-resolution traveltime-tomography models of P-wave velocity [Formula: see text] are constructed. They serve as input for acoustic full-waveform inversion (FWI), which we apply to derive high-resolution parameter models aiding the interpretation of the seismic data for potential hydrate and gas deposits. Synthetic tests indicate the applicability of the FWI approach to robustly reconstruct [Formula: see text] models with a typical hydrate and gas signature. Models of S-wave velocity [Formula: see text] containing a hydrate signature can only be reconstructed when the parameter distribution of [Formula: see text] is already well-known. When we add noise to the modeled data to simulate field-data conditions, it prevents the reconstruction of [Formula: see text] completely, justifying the application of an acoustic approach. We invert for [Formula: see text] models from field data of two parallel profiles of 14 km length with a distance of 1 km. Results indicate a characteristic velocity trend for hydrate and gas occurrence at BSR depth in the first of the analyzed profiles. We find no indications for gas accumulations below the BSR on the second profile and only weak indications for hydrate. These differences in the [Formula: see text] signature are consistent with the reflectivity behavior of the migrated seismic streamer data of both profiles in which a zone of high-reflectivity amplitudes is coincident with the potential gas zone derived from the FWI result. Calculating saturation estimates for the potential hydrate and gas zones yields values of up to 30% and 1.2%, respectively.

scholarly journals Crustal-scale depth imaging via joint full-waveform inversion of ocean-bottom seismometer data and pre-stack depth migration of multichannel seismic data: a case study from the eastern Nankai Trough

Solid Earth ◽  
2019 ◽  
Vol 10 (3) ◽  
pp. 765-784 ◽  
Author(s):  
Andrzej Górszczyk ◽  
Stéphane Operto ◽  
Laure Schenini ◽  
Yasuhiro Yamada
Keyword(s):  
Seismic Data ◽  
Nankai Trough ◽  
Waveform Inversion ◽  
Velocity Model ◽  
Full Waveform Inversion ◽  
Ocean Bottom ◽  
Ocean Bottom Seismometer ◽  
Depth Migration ◽  
Full Waveform ◽  
Air Gun

Abstract. Imaging via pre-stack depth migration (PSDM) of reflection towed-streamer multichannel seismic (MCS) data at the scale of the whole crust is inherently difficult. This is because the depth penetration of the seismic wavefield is controlled, firstly, by the acquisition design, such as streamer length and air-gun source configuration, and secondly by the complexity of the crustal structure. Indeed, the limited length of the streamer makes the estimation of velocities from deep targets challenging due to the velocity–depth ambiguity. This problem is even more pronounced when processing 2-D seismic data due to the lack of multi-azimuthal coverage. Therefore, in order to broaden our knowledge about the deep crust using seismic methods, we present the development of specific imaging workflows that integrate different seismic data. Here we propose the combination of velocity model building using (i) first-arrival tomography (FAT) and full-waveform inversion (FWI) of wide-angle, long-offset data collected by stationary ocean-bottom seismometers (OBSs) and (ii) PSDM of short-spread towed-streamer MCS data for reflectivity imaging, with the former velocity model as a background model. We present an application of such a workflow to seismic data collected by the Japan Agency for Marine-Earth Science and Technology (JAMSTEC) and the Institut Français de Recherche pour l'Exploitation de la Mer (IFREMER) in the eastern Nankai Trough (Tokai area) during the 2000–2001 Seize France Japan (SFJ) experiment. We show that the FWI model, although derived from OBS data, provides an acceptable background velocity field for the PSDM of the MCS data. From the initial PSDM, we refine the FWI background velocity model by minimizing the residual move-outs (RMOs) picked in the pre-stack-migrated volume through slope tomography (ST), from which we generate a better-focused migrated image. Such integration of different seismic datasets and leading-edge imaging techniques led to greatly improved imaging at different scales. That is, large to intermediate crustal units identified in the high-resolution FWI velocity model extensively complement the short-wavelength reflectivity inferred from the MCS data to better constrain the structural factors controlling the geodynamics of the Nankai Trough.

Localizing CO2 at Sleipner — Seismic images versus P-wave velocities from waveform inversion

Geophysics ◽  
2013 ◽  
Vol 78 (3) ◽  
pp. B131-B146 ◽  
Author(s):  
Manuel Queißer ◽  
Satish C. Singh
Keyword(s):  
Wave Velocity ◽  
Waveform Inversion ◽  
P Wave ◽  
Full Waveform Inversion ◽  
Wave Velocities ◽  
Full Waveform ◽  
P Wave Velocity ◽  
Seismic Image ◽  
P Wave Velocities ◽  
Seismic Images

The presence of injected [Formula: see text] in the Utsira Sand at the Sleipner site, Norway, is associated with a high negative P-wave velocity anomaly; that is, a low postinjection velocity and a strong seismic response. Time-lapse seismic imaging of [Formula: see text] injection at Sleipner is thus a viable monitoring tool of the injected [Formula: see text]. The work flow usually involves conventional seismic processing, including stacking, and results in seismic images. Multiple reflections, interference effects such as tuning, and the velocity pushdown effect due to [Formula: see text] injection render these seismic images ambiguous in terms of the localization and the quantification of the [Formula: see text] in the Utsira Sand. Nonetheless, seismic images often form the basis for analyses that aim to quantify the injected [Formula: see text]. We employed elastic 2D full waveform inversion to invert prestack seismic Sleipner data from preinjection (1994) and postinjection (1999) and compared the resulting postinjection P-wave velocity model with the corresponding seismic image. We found that the high-amplitude reflections in the seismic image do not everywhere coincide with low postinjection P-wave velocities. Drawing extensive and integrated conclusions is out of our scope, because this would require full control over the seismic data processing and a more comprehensive forward modeling. For instance, modeling should be done in 3D and an adequate anelasticity formulation should be added. However, the waveform inversion scheme we used accounts for all the aforementioned elastic propagation effects. The results therefore suggested that the exclusive use of seismic images to quantify [Formula: see text] could be revised and full waveform inversion should be added to the analysis toolbox.

scholarly journals Interparameter trade-off quantification for isotropic-elastic full-waveform inversion with various model parameterizations

Geophysics ◽  
2019 ◽  
Vol 84 (2) ◽  
pp. R185-R206 ◽  
Author(s):  
Wenyong Pan ◽  
Kristopher A. Innanen ◽  
Yu Geng ◽  
Junxiao Li
Keyword(s):  
Wave Velocity ◽  
Waveform Inversion ◽  
P Wave ◽  
Physical Parameters ◽  
Full Waveform Inversion ◽  
S Wave ◽  
Trade Off ◽  
Full Waveform ◽  
Trade Offs ◽  
P Wave Velocity

Simultaneous determination of multiple physical parameters using full-waveform inversion (FWI) suffers from interparameter trade-off difficulties. Analyzing the interparameter trade-offs in different model parameterizations of isotropic-elastic FWI, and thus determining the appropriate model parameterization, are critical for efficient inversion and obtaining reliable inverted models. Five different model parameterizations are considered and compared including velocity-density, modulus-density, impedance-density, and two velocity-impedance parameterizations. The scattering radiation patterns are first used for interparameter trade-off analysis. Furthermore, a new framework is developed to evaluate the interparameter trade-off based upon multiparameter Hessian-vector products: Multiparameter point spread functions (MPSFs) and interparameter contamination sensitivity kernels (ICSKs), which provide quantitative, second-order measurements of the interparameter contaminations. In the numerical experiments, the interparameter trade-offs in various model parameterizations are evaluated using the MPSFs and ICSKs. Inversion experiments are carried out with simple Gaussian-anomaly models and a complex Marmousi model. Overall, the parameterization of the P-wave velocity, S-wave velocity, and density, and the parameterization of the P-wave velocity, S-wave velocity, and S-wave impedance perform best for reconstructing all of the physical parameters. Isotropic-elastic FWI of the Hussar low-frequency data set with various model parameterizations verifies our conclusions.

Elastic full waveform inversion of multicomponent ocean-bottom cable seismic data: Application to Alba Field, U. K. North Sea

Geophysics ◽  
2010 ◽  
Vol 75 (6) ◽  
pp. R109-R119 ◽  
Author(s):  
Timothy J. Sears ◽  
Penny J. Barton ◽  
Satish C. Singh
Keyword(s):  
Wave Velocity ◽  
Seismic Data ◽  
Waveform Inversion ◽  
P Wave ◽  
Full Waveform Inversion ◽  
Ocean Bottom ◽  
S Wave ◽  
Wave Data ◽  
Data Inversion ◽  
Full Waveform

Elastic full waveform inversion of multichannel seismic data represents a data-driven form of analysis leading to direct quantification of the subsurface elastic parameters in the depth domain. Previous studies have focused on marine streamer data using acoustic or elastic inversion schemes for the inversion of P-wave data. In this paper, P- and S-wave velocities are inverted for using wide-angle multicomponent ocean-bottom cable (OBC) seismic data. Inversion is undertaken using a two-dimensional elastic algorithm operating in the time domain, which allows accurate modeling and inversion of the full elastic wavefield, including P- and mode-converted PS-waves and their respective amplitude variation with offset (AVO) responses. Results are presented from the application of this technique to an OBC seismic data set from the Alba Field, North Sea. After building an initial velocity model and extracting a seismic wavelet, the data are inverted instages. In the first stage, the intermediate wavelength P-wave velocity structure is recovered from the wide-angle data and then the short-scale detail from near-offset data using P-wave data on the [Formula: see text] (vertical geophone) component. In the second stage, intermediate wavelengths of S-wave velocity are inverted for, which exploits the information captured in the P-wave’s elastic AVO response. In the third stage, the earlier models are built on to invert mode-converted PS-wave events on the [Formula: see text] (horizontal geophone) component for S-wave velocity, targeting first shallow and then deeper structure. Inversion of [Formula: see text] alone has been able to delineate the Alba Field in P- and S-wave velocity, with the main field and outlier sands visible on the 2D results. Inversion of PS-wave data has demonstrated the potential of using converted waves to resolve shorter wavelength detail. Even at the low frequencies [Formula: see text] inverted here, improved spatial resolution was obtained by inverting S-wave data compared with P-wave data inversion results.

Sign in / Sign up

Export Citation Format

Share Document