Flow and Thermal Field Measurement Techniques

Author(s):  
Je-Chin Han ◽  
Lesley M. Wright
Strain ◽  
2018 ◽  
Vol 55 (1) ◽  
pp. e12301 ◽  
Author(s):  
Noëlie Di Cesare ◽  
Guillaume Corvec ◽  
Jean-Benoît Le Cam ◽  
Xavier Balandraud ◽  
Julien Gauffreteau

Silva Fennica ◽  
2006 ◽  
Vol 40 (4) ◽  
Author(s):  
Lauri Korhonen ◽  
Kari Korhonen ◽  
Miina Rautiainen ◽  
Pauline Stenberg

2011 ◽  
Vol 11 (8) ◽  
pp. 3611-3629 ◽  
Author(s):  
T. T. van Leeuwen ◽  
G. R. van der Werf

Abstract. Fires are a major source of trace gases and aerosols to the atmosphere. The amount of biomass burned is becoming better known, most importantly due to improved burned area datasets and a better representation of fuel consumption. The spatial and temporal variability in the partitioning of biomass burned into emitted trace gases and aerosols, however, has received relatively little attention. To convert estimates of biomass burned to trace gas and aerosol emissions, most studies have used emission ratios (or emission factors (EFs)) based on the arithmetic mean of field measurement outcomes, stratified by biome. However, EFs vary substantially in time and space, even within a single biome. In addition, it is unknown whether the available field measurement locations provide a representative sample for the various biomes. Here we used the available body of EF literature in combination with satellite-derived information on vegetation characteristics and climatic conditions to better understand the spatio-temporal variability in EFs. While focusing on CO, CH4, and CO2, our findings are also applicable to other trace gases and aerosols. We explored relations between EFs and different measurements of environmental variables that may correlate with part of the variability in EFs (tree cover density, vegetation greenness, temperature, precipitation, and the length of the dry season). Although reasonable correlations were found for specific case studies, correlations based on the full suite of available measurements were lower and explained about 33%, 38%, 19%, and 34% of the variability for respectively CO, CH4, CO2, and the Modified Combustion Efficiency (MCE). This may be partly due to uncertainties in the environmental variables, differences in measurement techniques for EFs, assumptions on the ratio between flaming and smoldering combustion, and incomplete information on the location and timing of EF measurements. We derived new mean EFs, using the relative importance of each measurement location with regard to fire emissions. These weighted averages were relatively similar to the arithmetic mean. When using relations between the environmental variables and EFs to extrapolate to regional and global scales, we found substantial differences, with for savannas 13% and 22% higher CO and CH4 EFs than the arithmetic mean of the field studies, possibly linked to an underrepresentation of woodland fires in EF measurement locations. We argue that from a global modeling perspective, future measurement campaigns could be more beneficial if measurements are made over the full fire season, and if relations between ambient conditions and EFs receive more attention.


Author(s):  
Patrick Yeung ◽  
Ryan Sporns ◽  
Stuart Clouston ◽  
Grant A. Coleman ◽  
Scott Miller ◽  
...  

Magnetic Flux Leakage inspection tools are generally calibrated on a series of manufactured defects. This has been shown to give good results on a wide range of defects in varying wall thicknesses, velocities and pipeline conditions. Significant improvements in sizing performance can be achieved if sizing algorithms can be optimized on high resolution field data with low uncertainty that more closely reflects the actual line specific corrosion dimensions and profiles. The effects of defect profile can be significant to the MFL signal response. In order to achieve this goal, very high resolution and accurate field measurement techniques are needed to map the combined profile of a significant number of corrosion defects. This paper discusses a process for developing high performance sizing algorithms that consistently better industry standards for MFL sizing performance in areas of high density or complex corrosion in both oil and gas pipelines through the incorporation of high resolution laser scan technology. Complex corrosion may be considered as an area wherein individual corrosions interact together such that they no longer behave as a single corrosion and the MFL response experiences a superposition of leakage signals. A review of the methodology will be discussed and the results demonstrated through case studies from both Enbridge Pipelines Inc. and TransCanada Pipelines Ltd. where high-resolution field data was used as the basis for sizing model optimization.


1985 ◽  
pp. 30-37
Author(s):  
Kuniichiro MIYASHITA ◽  
Kenji AOKI ◽  
Tetsuya HANAMURA ◽  
Takaya TAJIMA

Sign in / Sign up

Export Citation Format

Share Document