Fundamental Mass Transfer Concepts in Engineering Applications

2019 ◽  
Author(s):  
Ismail Tosun
2008 ◽  
Vol 11 (sup001) ◽  
pp. 53-55
Author(s):  
B. Carpentier ◽  
A. Gautier ◽  
P. Paullier ◽  
A. Ould-Dris ◽  
P. Layrolle ◽  
...  

2014 ◽  
Vol 986-987 ◽  
pp. 998-1003
Author(s):  
Lu Ping Bai ◽  
Li Zhang ◽  
Xiao Feng Lu

Based on that the film filling was simplified to the flat plate model, the heat and mass transfer of the filling zone with fouling in cooling tower were analyzed. The effect of fouling on the performance of filler was analyzed according to the dirt growth model. The work done in this paper can simply forecast changes in cooling tower performance caused by the filler fouling. It will lay a theoretical foundation for accurately calculating the performance coefficient of filler. And it is helpful to solving the problem of no the ripe empirical formula of filler performance with fouling for engineering applications.


1963 ◽  
Vol 85 (4) ◽  
pp. 395-401 ◽  
Author(s):  
Reno R. Cole ◽  
Yoram Hopenfeld

A method of polishing metals by means of an electrolytic jet at extremely high current densities (to 1750 amps per sq in.) is described. Data are presented on the relation of polishing effect on various metals to current density and electrolyte flow rate for several electrolytes. An experimental method is described whereby the relationship of the above factors can be determined. It was found that all metals investigated could be polished at high enough current densities. Previous theories of electrolytic polishing are discussed and shown to not fully account for the process investigated. A modified theory to account for polishing at the high current densities observed is presented and is supported by mathematical analysis based on fundamental mass transfer considerations.


2019 ◽  
Vol 11 (16) ◽  
pp. 4443 ◽  
Author(s):  
Afridi ◽  
Jing ◽  
Younas

Anaerobic granules are responsible for organic degradation and biogas production in a reactor. The biogas production is entirely dependent on a mass transfer mechanism, but so far, the fundamental understanding remains poor due to the covered surface of the reactor. The study aimed at investigating the fundamental mass transfer characteristics of single anaerobic granules of different sizes using microscopic imaging and analytical monitoring under single and different organic loadings. The experiment was conducted in a micro reactor and mass transfer was calculated using modified Fick’s law. Scanning electron microscopy was applied to observe biogas production zones in the granule, and a lab-scale microscope equipped with a camera revealed the biogas bubble detachment process in the micro reactor for the first time. In this experiment, the granule size was 1.32, 1.47, and 1.75 mm, but 1.75 mm granules were chosen for further investigation due to their large size. The results revealed that biogas production rates for 1.75 mm granules at initial Chemical Oxygen Demand (COD) 586, 1700, and 6700 mg/L were 0.0108, 0.0236, and 0.1007 m3/kg COD, respectively; whereas the mass transfer rates were calculated as 1.83 × 10−12, 5.30 × 10−12, and 2.08 × 10−11 mg/s. It was concluded that higher organic loading and large granules enhance the mass transfer inside the reactor. Thus, large granules should be preferred in the granule-based reactor to enhance biogas production.


Indoor Air ◽  
1993 ◽  
Vol 3 (4) ◽  
pp. 263-268 ◽  
Author(s):  
Bruce A. Tichenor ◽  
Zhishi Guo ◽  
Leslie E. Sparks

Sign in / Sign up

Export Citation Format

Share Document