Overstrain in flush optimal-chamfered cross-bored cylinders

2006 ◽  
Vol 220 (1) ◽  
pp. 15-25
Author(s):  
J M Kihiu ◽  
G O Rading ◽  
S M Mutuli
Keyword(s):  
Yield Criterion ◽  
Three Dimensional ◽  
Yield Condition ◽  
Meridional Plane ◽  
Stress Distributions ◽  
Dimensional Finite Element ◽  
Von Mises ◽  
Three Dimensional Finite Element ◽  
Stress Reversals ◽  
Incremental Theory Of Plasticity

A three-dimensional finite-element method computer program was developed to establish the elastic—plastic, residual, and service stress distributions in cylinders with flush and non-protruding optimal-chamfered cross-bores under internal pressure. Eight-noded brick and four-noded tetrahedral isoparametric elements and the displacement formulation were used. The incremental theory of plasticity with a 5 per cent yield condition and von Mises yield criterion were assumed. The incipient and 5 per cent overstrain (ov) pressures were established for various thickness ratios and cross-bore to main bore radius ratios. For the optimum chamfer angle geometrical configuration, the stresses were determined for varying ov. The maximum and minimum effective stresses were located 7.5° from the meridional and transverse planes, respectively. Meridional plane through thickness yielding occurred at an ov of 41 per cent. The service stress gradients at the cross-bore chamfer end increased with ov for ovs >30 per cent. Stress reversals were eliminated for overstrain >27 per cent. Alternative autofrettage and yield condition procedures were proposed.

Overstraining of flush plain cross-bored cylinders

2004 ◽  
Vol 218 (2) ◽  
pp. 143-153 ◽  
Author(s):  
J M Kihiu ◽  
G O Rading ◽  
S M Mutuli
Keyword(s):  
Finite Element Method ◽  
Yield Criterion ◽  
Three Dimensional ◽  
Yield Condition ◽  
Solution Technique ◽  
Stress Distributions ◽  
Dimensional Finite Element ◽  
Von Mises ◽  
Three Dimensional Finite Element ◽  
Incremental Theory Of Plasticity

A three-dimensional finite element method computer program was developed to establish the elastic-plastic, residual and service stress distributions in thick-walled cylinders with flush and non-protruding plain cross bores under internal pressure. The displacement formulation and eight-noded brick isoparametric elements were used. The incremental theory of plasticity with a 5 per cent yield condition (an element is assumed to have yielded when the effective stress is within 5 per cent of the material yield stress) and von Mises yield criterion were assumed. The frontal solution technique was used. The incipient yield pressure and the pressure resulting in a 0.3 per cent overstrain ratio were established for various cylinder thickness ratios and cross bore-main bore radius ratios. For a thickness ratio of 2.25 and a cross bore-main bore radius ratio of 0.1, the stresses were determined for varying overstrain and an optimum overstrain ratio of 37 per cent was established. To find the accuracy of the results, the more stringent yield condition of 0.5 per cent was also considered. The benefits of autofrettage were presented and alternative autofrettage and yield condition procedures proposed.

A Three-Dimensional Finite Element Stress Analysis and Strength Prediction of CFRP Adhesive Laminated Plates Subjected to Static and Impact Out-of-Plane Loadings

2009 ◽  
Author(s):  
Yukiya Noshita ◽  
Toshiyuki Sawa ◽  
Yuya Omiya
Keyword(s):  
Equivalent Stress ◽  
Three Dimensional ◽  
Laminated Plates ◽  
Stress Distributions ◽  
Maximum Value ◽  
Out Of Plane ◽  
Dimensional Finite Element ◽  
Von Mises Equivalent Stress ◽  
Von Mises ◽  
Three Dimensional Finite Element

Stress distributions in CFRP adhesive laminated plates subjected to static and impact out-of-plane loadings are analyzed using a three-dimensional finite-element method (FEM). For establishing an optimum design method of the laminated plates, the effects of some factors are examined. As the results, it is found that the maximum value of the von Mises equivalent stress σ eqv occurs at the edge of the CFRP’s interfaces. The maximum value of interface shear stress r i at CFRP interface decreases as the reinforced Young’s modulus and the thickness increases. However, the maximum value of σ eqv at the adhesive layer decreases as the reinforced Young’s modulus and the thickness decreases. In addition, the maximum value of r i at the CFRP’s interface of lower reinforced laminates under impact loadings shows opposite characteristics to those under static loadings. For verification of the FEM calculations, experiments were carried out to measure the strains at the interfaces and the laminates plates strengths. Concerning strain and strength prediction based on von Mises equivalent stress, fairly good agreements were found between the numerical and the experimental results. The FEM results of impacted strain are in fairly good consistent with the measured results. Discussion is made on the effects of some factors on interface stress distributions.

scholarly journals Finite Element Analysis of Dental Implants with Zirconia Crown Restorations: Conventional Cement-Retained vs. Cementless Screw-Retained

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2666
Author(s):  
Jae-Hyun Lee ◽  
Ho Yeol Jang ◽  
Su Young Lee
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Stress Distributions ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Von Mises ◽  
Three Dimensional Finite Element ◽  
Oblique Load ◽  
Surrounding Bone

The present study was designed to compare the stress distributions in two restoration types of implants and the surrounding bone. The first restoration type was a conventional cement-retained zirconia crown, and the second was a novel cementless screw-retained zirconia crown with a base abutment. A three-dimensional finite element method was used to model the implants, restorations, and supporting bone. A comparative study of the two implants was performed under two masticatory loads: a vertical load of 100 N and a 30-degree oblique load of 100 N. Under both loading conditions, the maximum von Mises stress and strain values in the implant and supporting bone were higher in the conventional cement-retained restoration model than in the cementless screw-retained model. In terms of stress distribution, the cementless screw-retained zirconia crown with base abutment may be considered a superior restoration option compared to the conventional cement-retained zirconia crown.

Evaluation of Burst Pressure of Corroded Pipe Segments Using Three-Dimensional Finite Element Analyses

2018 ◽  
Author(s):  
Ji Bao ◽  
Shulong Zhang ◽  
Wenxing Zhou ◽  
Shenwei Zhang
Keyword(s):  
Finite Element ◽  
Yield Criterion ◽  
Three Dimensional ◽  
Full Scale ◽  
Burst Pressure ◽  
Dimensional Finite Element ◽  
Tresca Criterion ◽  
Von Mises ◽  
Three Dimensional Finite Element ◽  
The Impact

In this paper, three-dimensional finite element models are developed to simulate full-scale burst tests of corroded pipes containing multiple naturally occurring corrosion anomalies. Both the von Mises and Tresca yield criteria and associated flow rules are employed in finite element analysis (FEA). For the Tresca criterion, the corresponding constitutive model subroutine is developed and incorporated in the FEA. The accuracy of FEA is investigated by comparing the burst pressures observed in the tests and corresponding burst pressures predicted using FEA. The implications of using the von Mises and Tresca criteria for the accuracy of the predicted burst pressure are investigated. Sensitivity analyses are also carried out to investigate the impact on the predicted burst pressure due to the mesh density in the corroded region, characterization of the geometry of the corrosion cluster and different types of element (e.g. solid and shell elements) used in FEA. The results suggest that the Tresca criterion always underestimates the burst pressure and the von Mises yield criterion predicts the burst pressure accurately. This study demonstrates the feasibility of using high-fidelity FEA and the Tresca yield criterion to simulate full-scale burst tests of corroded pipes and therefore establish a large database of burst pressure capacities of corroded pipes that can be used to develop an accurate, practical burst pressure capacity model amenable to the pipeline integrity management practice.

Residual Stress Prediction for Non-Axisymmetric Vessel Penetration Welds

2008 ◽  
Author(s):  
Kazuo Ogawa ◽  
Nobuyoshi Yanagida ◽  
Koichi Saito
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Three Dimensional ◽  
Measurement Data ◽  
Fe Model ◽  
Stress Distributions ◽  
Dimensional Finite Element ◽  
Stress Prediction ◽  
Three Dimensional Finite Element ◽  
Good Agreement

Residual stress distribution in an oblique nozzle jointed to a vessel with J-groove welds was analyzed using a three-dimensional finite element method. All welding passes were considered in a 180-degree finite element (FE) model with symmetry. Temperature and stress were modeled for simultaneous bead laying. To determine residual stress distributions at the welds experimentally, a mock-up specimen was manufactured. The analytical results show good agreement with the experimental measurement data, indicating that FE modeling is valid.

A comparative study between zirconia and titanium abutments on the stress distribution in parafunctional loading: A 3D finite element analysis

2020 ◽  
Vol 28 (6) ◽  
pp. 603-613 ◽  
Author(s):  
Efe Can Sivrikaya ◽  
Mehmet Sami Guler ◽  
Muhammed Latif Bekci
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Principal Stresses ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
3D Fea ◽  
Von Mises ◽  
Three Dimensional Finite Element

BACKGROUND: Zirconia has become a popular biomaterial in dental implant systems because of its biocompatible and aesthetic properties. However, this material is more fragile than titanium so its use is limited. OBJECTIVES: The aim of this study was to compare the stresses on morse taper implant systems under parafunctional loading in different abutment materials using three-dimensional finite element analysis (3D FEA). METHODS: Four different variations were modelled. The models were created according to abutment materials (zirconia or titanium) and loading (1000 MPa vertical or oblique on abutments). The placement of the implants (diameter, 5.0 × 15 mm) were mandibular right first molar. RESULTS: In zirconia abutment models, von Mises stress (VMS) values of implants and abutments were decreased. Maximum and minimum principal stresses and VMS values increased in oblique loading. VMS values were highest in the connection level of the conical abutments in all models. CONCLUSIONS: Using conical zirconia abutments decreases von Mises stress values in abutments and implants. However, these values may exceed the pathological limits in bruxism patients. Therefore, microfractures may be related to the level of the abutment.

scholarly journals A three - dimensional finite element study on the stress distribution pattern of two prosthetic abutments for external hexagon implants

2013 ◽  
Vol 07 (04) ◽  
pp. 484-491 ◽  
Author(s):  
Wagner Moreira ◽  
Caio Hermann ◽  
Jucélio Tomás Pereira ◽  
Jean Anacleto Balbinoti ◽  
Rodrigo Tiossi
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
3D Fea ◽  
The One ◽  
Von Mises ◽  
Three Dimensional Finite Element

ABSTRACT Objective: The purpose of this study was to evaluate the mechanical behavior of two different straight prosthetic abutments (one- and two-piece) for external hex butt-joint connection implants using three-dimensional finite element analysis (3D-FEA). Materials and Methods: Two 3D-FEA models were designed, one for the two-piece prosthetic abutment (2 mm in height, two-piece mini-conical abutment, Neodent) and another one for the one-piece abutment (2 mm in height, Slim Fit one-piece mini-conical abutment, Neodent), with their corresponding screws and implants (Titamax Ti, 3.75 diameter by 13 mm in length, Neodent). The model simulated the single restoration of a lower premolar using data from a computerized tomography of a mandible. The preload (20 N) after torque application for installation of the abutment and an occlusal loading were simulated. The occlusal load was simulated using average physiological bite force and direction (114.6 N in the axial direction, 17.1 N in the lingual direction and 23.4 N toward the mesial at an angle of 75° to the occlusal plan). Results: The regions with the highest von Mises stress results were at the bottom of the initial two threads of both prosthetic abutments that were tested. The one-piece prosthetic abutment presented a more homogeneous behavior of stress distribution when compared with the two-piece abutment. Conclusions: Under the simulated chewing loads, the von Mises stresses for both tested prosthetic-abutments were within the tensile strength values of the materials analyzed which thus supports the clinical use of both prosthetic abutments.

Optimization of Adhesively Bonded Spar-Wingskin Joints of Laminated FRP Composites Subjected to Pull-Off Load: A Critical Review

2020 ◽  
Vol 8 (1) ◽  
pp. 29-46
Author(s):  
S. Rakshe ◽  
S. V. Nimje ◽  
S. K. Panigrahi
Keyword(s):  
Three Dimensional ◽  
Von Mises Stress ◽  
Geometrical Parameters ◽  
Adhesively Bonded ◽  
Element Analysis ◽  
Frp Composites ◽  
Dimensional Finite Element ◽  
Materials Used ◽  
Von Mises ◽  
Three Dimensional Finite Element

A review on optimization of adhesively bonded spar-wingskin joint (SWJ) of laminated fiber reinforced polymer (FRP) composites subjected to pull-off load is presented in this article using three-dimensional finite element analysis. Von Mises stress components have been computed across the width of joint at different interfaces viz. load coupler-spar, and load coupler-wingskin interfaces. Further, the weight of SWJ structure is considered as the objective function which needs to be minimized for optimization. In the first step, the material and lamination scheme of the FRP composite materials used for SWJ are optimized, and, in the second step, the geometrical parameters have been optimized on the basis of minimum von Mises stress and weight. Further, the effects of the material, lamination scheme, and geometrical parameters on the von Mises stress and weight have been validated using the Analysis of Variance (ANOVA) approach as prescribed by the Taguchi method. The results show that the material and spar thickness are the most significant factors influencing von Mises stress. The weight analysis reveals that there is a significant effect of change in material and wingskin thickness on SWJ performance. Suitable design recommendations have been made for SWJ in terms of material, lamination scheme and geometrical parameters.

Sign in / Sign up

Export Citation Format

Share Document