scholarly journals An experimental study of the dual-fuel performance of a small compression ignition diesel engine operating with three gaseous fuels

2007 ◽  
Vol 221 (8) ◽  
pp. 943-956 ◽  
Author(s):  
J Stewart ◽  
A Clarke ◽  
R Chen
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
High Speed ◽  
Direct Injection ◽  
Specific Energy Consumption ◽  
Dual Fuel ◽  
Compression Ignition ◽  
Gaseous Fuels ◽  
Ci Engine

A dual-fuel engine is a compression ignition (CI) engine where the primary gaseous fuel source is premixed with air as it enters the combustion chamber. This homogenous mixture is ignited by a small quantity of diesel, the ‘pilot’, that is injected towards the end of the compression stroke. In the present study, a direct-injection CI engine, was fuelled with three different gaseous fuels: methane, propane, and butane. The engine performance at various gaseous concentrations was recorded at 1500 r/min and quarter, half, and three-quarters relative to full a load of 18.7 kW. In order to investigate the combustion performance, a novel three-zone heat release rate analysis was applied to the data. The resulting heat release rate data are used to aid understanding of the performance characteristics of the engine in dual-fuel mode. Data are presented for the heat release rates, effects of engine load and speed, brake specific energy consumption of the engine, and combustion phasing of the three different primary gaseous fuels. Methane permitted the maximum energy substitution, relative to diesel, and yielded the most significant reductions in CO2. However, propane also had significant reductions in CO2 but had an increased diffusional combustion stage which may lend itself to the modern high-speed direct-injection engine.

scholarly journals The classification of gasoline/diesel dual-fuel combustion based on the heat release rate shapes and its application in a light-duty single-cylinder engine

2018 ◽  
Vol 20 (1) ◽  
pp. 69-79 ◽  
Author(s):  
Jeongwoo Lee ◽  
Sanghyun Chu ◽  
Jaegu Kang ◽  
Kyoungdoug Min ◽  
Hyunsung Jung ◽  
...  
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Thermal Efficiency ◽  
Fuel Combustion ◽  
Dual Fuel ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Dual Fuel Combustion ◽  
Compression Ignition Combustion

In this research, there are two major sections for analysis: the characteristics of gasoline and diesel dual-fuel combustion and their application to operating load extension with high thermal efficiency and low emissions. All the experiments were completed using a single-cylinder compression ignition engine with 395 cc displacement. In the first section, the dual-fuel combustion modes were classified into three cases by their heat release rate shapes. Staying at 1500 r/min with a total value of 580 J of low heat for each cycle condition, the diesel injection timing was varied from before top dead center with a 6–46 °crank angle with 70% of gasoline fraction based on the low heating value. Among the modes were two suitable dual-fuel combustion modes for a premixed compression ignition. The first suitable mode shows multiple peaks in the heat release rate (mode 2) and the second suitable mode shows a single peak with a “bell-shaped” heat release rate (mode 3). These two dual-fuel combustion types showed a high gross indicated thermal efficiency of up to 46%. Based on the results in the first section, the practical application of dual-fuel premixed compression ignition combustion was investigated considering a high thermal efficiency and a high-load condition. At a 1500 r/min/gross indicated mean effective pressure of 6.5 bar, 48% of the gross indicated thermal efficiency was obtained by using dual-fuel premixed compression ignition combustion mode 3. This mode was typical of a “reactivity controlled compression ignition,” while the nitrogen oxides and the particulate matter emissions satisfied the EURO-6 regulation (0.21 g/kW h and 2.8 mg/m3, respectively). In addition, a high thermal efficiency (45%) with low maximum pressure rise rate, NOx (nitrogen oxides), and particulate matter emissions was obtained at 2000 r/min/gross indicated mean effective pressure 14 bar condition by the adjustment of dual-fuel premixed compression ignition combustion mode 2. As a result, this research contributes to the understanding and practical application of dual-fuel combustion for a light-duty compression ignition engine.

Predicting Ignition and Combustion of a Pilot Ignited Natural Gas Jet Using Numerical Simulation Based on Detailed Chemistry

2017 ◽  
Author(s):  
Michael Jud ◽  
Georg Fink ◽  
Thomas Sattelmayer
Keyword(s):  
Natural Gas ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Direct Injection ◽  
Dual Fuel ◽  
Pressure Curve ◽  
Detailed Chemistry ◽  
Dual Fuel Combustion ◽  
Good Agreement

In this paper, a multidimensional computational fluid dynamics (CFD) model coupled with detailed chemistry calculations was used to analyze dual-fuel combustion based on high pressure direct injection of natural gas. The main focus was to analyze the capability of predicting pressure curve and heat release rate (HRR) for different injection strategies. Zero-dimensional homogeneous constant volume reactor calculations were used to select a reaction mechanism for the temperature range below 800 K. As the best-performing mechanism, the Chalmers mechanism was chosen. To validate the numerical model, the setup was first split into a single gas injection and a single Diesel injection. They were validated individually using shadowgraphs obtained from a Rapid Compression Expansion Machine (RCEM). Diesel ignition timing and position in the combustion chamber were close to experimental results. Gas direct injection showed good agreement with regard to penetration and mixing. In the dual-fuel setup, the injection timing of natural gas was varied to create a first case with mainly diffusive combustion and a second case with mainly premixed combustion of natural gas. For both setups good agreement with pressure curve and heat release rate were achieved. A qualitative comparison of shadowgraphs with the density field highlights the important points to predict dual-fuel combustion.

Analysis of the effect of syngas substitution of diesel on the Heat Release Rate and combustion behaviour of Diesel-Syngas dual fuel engine

Fuel ◽  
2022 ◽  
Vol 312 ◽  
pp. 122842
Author(s):  
Francis Omotola Olanrewaju ◽  
Hu Li ◽  
Zahida Aslam ◽  
James Hammerton ◽  
Jon C. Lovett
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Dual Fuel

Synchronization During Multi-Mode Thermoacoustic Oscillations in a Liquid-Fueled Gas Turbine Combustor at Elevated Pressure

2019 ◽  
Author(s):  
Mitchell L. Passarelli ◽  
J. D. Maxim Cirtwill ◽  
Timothy Wabel ◽  
Adam M. Steinberg ◽  
A. J. Wickersham
Keyword(s):  
Heat Release ◽  
Gas Turbine ◽  
Heat Release Rate ◽  
Release Rate ◽  
High Speed ◽  
Elevated Pressure ◽  
Fuel Injector ◽  
Frequency Pulling ◽  
Industrial Gas Turbine ◽  
Thermoacoustic Oscillations

Abstract This paper analyzes intermittent self-excited thermoacoustic oscillations in which the pressure (P′) and heat release rate (q̇′) fluctuations are harmonically coupled. That is to say, P′ and q̇′ do not oscillate at the same frequencies, but rather at frequencies in integer ratios. Thus, this system represents a case dominated by nonlinear cross-mode coupling. The measurements were obtained in an optically-accessible combustor equipped with an industrial gas turbine fuel injector operating with liquid fuel under partially-premixed conditions at elevated pressure. High-speed chemiluminescence (CL) imaging of OH* was used as an indicator of the heat release rate. The data was processed using spectral proper orthogonal decomposition (SPOD) to isolate the dominant heat release and pressure modes. Synchronization theory was used to determine when the modes are coupled and how their interaction manifests in the measurements, particularly how it relates to the observed intermittency. The results show three distinct intervals of synchronized oscillation shared by all the mode pairs analyzed. The first interval exhibits the same characteristics as a pair of noisy, phase-locked self-oscillators, with phase-slipping and frequency-pulling. While the behaviour of the second interval differs among mode pairs, strong frequency-pulling is observed during the third interval for all pairs.

scholarly journals Improved model for the analysis of the Heat Release Rate (HRR) in Compression Ignition (CI) engines

2020 ◽  
Vol 93 (5) ◽  
pp. 1901-1913 ◽  
Author(s):  
Francis O. Olanrewaju ◽  
Hu Li ◽  
Gordon E. Andrews ◽  
Herodotos N. Phylaktou
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Compression Ignition ◽  
Improved Model ◽  
Ci Engines
Sign in / Sign up

Export Citation Format

Share Document