Wear of ultra-high molecular weight polyethylene acetabular cups in a physiological hip joint simulator in the anatomical position using bovine serum as a lubricant

1997 ◽  
Vol 211 (3) ◽  
pp. 265-269 ◽  
Author(s):  
R J A Bigsby ◽  
C S Hardaker ◽  
J Fisher
Keyword(s):  
Molecular Weight ◽  
Stainless Steel ◽  
High Molecular Weight ◽  
Hip Joint ◽  
Bovine Serum ◽  
Clinical Results ◽  
Zirconia Ceramic ◽  
Wear Rates ◽  
Ultra High Molecular Weight ◽  
Hip Joint Simulator

The Leeds physiological anatomical (PA) hip joint simulator was developed to apply three axes of loading and a complex three-dimensional motion so that the forces and motions can reproduce exactly the walking cycles defined by Paul. This paper presents the results of a study using the Leeds PA hip joint simulator to determine the wear of 32 mm ultra-high molecular weight polyethylene (UHMWPE) acetabular cups against stainless steel and zirconia ceramic heads, using bovine serum as lubricant. These results have been compared with the results of a previous study that used water as the lubricant, which led to UHMWPE transfer film being formed on the stainless steel head. Comparisons are also made with clinical results and results from other simulators. The study indicates that it is preferable to use bovine serum in simulator studies. In addition, the results indicate that if the surface roughness of the metallic and femoral heads are similar, and they remain undamaged during the tests, the wear rates of the UHMWPE cups are likely to be similar.

Comparison of wear of ultra-high molecular weight polyethylene acetabular cups against surface-engineered femoral heads

2008 ◽  
Vol 222 (7) ◽  
pp. 1073-1080 ◽  
Author(s):  
A Galvin ◽  
C Brockett ◽  
S Williams ◽  
P Hatto ◽  
A Burton ◽  
...  
Keyword(s):  
Molecular Weight ◽  
High Molecular Weight ◽  
Hip Joint ◽  
Vapour Deposition ◽  
Polyethylene Wear ◽  
Chemical Vapour ◽  
Alumina Ceramic ◽  
Femoral Heads ◽  
Ultra High Molecular Weight ◽  
Hip Joint Simulator

Alumina ceramic heads have been previously shown to reduce polyethylene wear in comparison to cobalt chrome (CoCr) heads in artificial hip joints. However, there are concerns about the brittle nature of ceramics. It is therefore of interest to investigate ceramic-like coatings on metallic heads. The aim of this study was to compare the friction and wear of ultra-high molecular weight polyethylene (UHMWPE) against alumina ceramic, CoCr, and surface-engineered ceramic-like coatings in a friction simulator and a hip joint simulator. All femoral heads tested were 28 mm diameter and included: Biolox™ Forte alumina, CoCr, arc evaporative physical vapour deposition (AEPVD) chromium nitride (CrN) coated CoCr, plasma-assisted chemical vapour deposition (PACVD) amorphous diamond-like carbon (aDLC) coated CoCr, sputter CrN coated CoCr, reactive gas controlled arc (RGCA) AEPVD titanium nitride (TiN) coated CoCr, and Graphit-iC™ coated CoCr. These were articulated against UHMWPE acetabular cups in a friction simulator and a hip joint simulator. Alumina and CoCr gave the lowest wear volumes whereas the sputter coated CrN gave the highest. Alumina also had the lowest friction factor. There was an association between surface parameters and wear. This study indicates that surface topography of surface-engineered femoral heads is more important than friction and wettability in controlling UHMWPE wear.

The influence of phospholipid concentration in protein-containing lubricants on the wear of ultra-high molecular weight polyethylene in artificial hip joints

2001 ◽  
Vol 215 (2) ◽  
pp. 259-263 ◽  
Author(s):  
J Bell ◽  
J L Tipper ◽  
E Ingham ◽  
M H Stone ◽  
J Fisher
Keyword(s):  
Molecular Weight ◽  
High Molecular Weight ◽  
Phosphatidyl Choline ◽  
Bovine Serum ◽  
Hip Joints ◽  
Wear Rates ◽  
Artificial Hip ◽  
Artificial Hip Joints ◽  
Ultra High Molecular Weight

There is considerable interest in the wear of polyethylene and the resulting wear-debrisinduced osteolysis in artificial hip joints. Proteins play an important role as boundary lubricants in vivo in the pseudosynovial fluid, and these are reproduced in in vitro tests through the use of bovine serum. Little is known, however, about the effect of phospholipid concentrations within proteinaceous solutions on the wear of ultra-high molecular weight polyethylene (UHMWPE). The effects of protein-containing lubricants with 0.05, 0.5 and 5 per cent (w/v) phosphatidyl choline concentrations on the wear of ultra-high molecular weight polyethylene (UHMWPE) were compared with 25 per cent (v/v) bovine serum which had 0.01 per cent (w/v) lipid; the effects were compared in a hip joint simulator with smooth (n = 4) and scratched (n = 3) femoral heads. The control bovine serum lubricant produced UHWMPE wear of 55 and 115mm3/106 cycles on the smooth and rough heads respectively. The increased phospholipid concentration significantly reduced the wear rate. At the higher concentration (5% w/v phosphatidyl choline) the average wear was reduced to less than 2 mm3/106 cycles. Even with the relatively low concentrations of 0.05% w/v phosphatidyl choline the wear was reduced by at least threefold compared with the bovine serum tests for both the smooth and rough femoral heads. There may be considerable differences in the phospholipid concentrations in patients' synovial fluid and this is highly likely to produce considerable variation in wear rates. In vitro, differences in the phospholipid concentration of lubricants may also cause variation in wear rates between different simulator tests.

Wear Behaviour and Wear Debris Characterization of UHMWPE on Alumina Ceramic, Stainless Steel, CoCrMo and Ti6Al4V Hip Prostheses in a Hip Joint Simulator

2010 ◽  
Vol 7 ◽  
pp. 7-25 ◽  
Author(s):  
Shi Bo Wang ◽  
Shi Rong Ge ◽  
Hong Tao Liu ◽  
Xiao Long Huang
Keyword(s):  
Molecular Weight ◽  
Stainless Steel ◽  
Size Distribution ◽  
High Molecular Weight ◽  
Hip Joint ◽  
Wear Debris ◽  
Wear Behavior ◽  
Debris Particles ◽  
Directional Motion ◽  
Ultra High Molecular Weight

Ultra-high molecular-weight polyethylene (UHMWPE) has been used in total hip replacement for the last three decades. Despite the advancements in prosthesis design, the wear of UHMWPE remains a serious clinical problem; the release of wear debris may induce osteolysis and implant loosening. Understanding of wear behavior and wear debris morphology of the polyethylene is essential to improve the reliability of hip joint implants. The investigation in this paper carried out wear simulation tests of UHMWPE on Al2O3, 316L stainless steel, CoCrMo alloy and Ti6Al4V alloy, respectively. The lubrication of plasma solution and bovine serum solution was presented in wear tests. The effect of motion and loading on the wear behavior and wear debris morphology, and the influence of femoral head material and assembly style were studied in order to obtain a better understanding of the morphology of ultra-high molecular weight polyethylene wear particles. It is shown that the wear of UHMWPE acetabular cups against metal femoral heads was significantly higher than that against ceramic heads. The presence of protein in lubricant increases the wear of UHMWPE acetabular cups on Al2O3 heads. The wear rates of UHMWPE in multi-directional motion are approximately 2.5 times of those in uni-directional motion. The size distribution range of the UHMWPE debris particles for all head materials varies from submicron particles up to several hundreds micron. The size distribution range of wear debris particles is not directly related to wear resistance of UHMWPE, but significantly influenced by wear mechanisms. The UHMWPE debris particles produced in hip wear simulation tests are classified as round debris, flake-like debris and stick debris, which are closely related to the primary mechanisms of abrasive wear, adhesive wear and fatigue wear.

Sign in / Sign up

Export Citation Format

Share Document