Influence of the state of the inlet endwall boundary layer on the interaction between pressure surface separation and endwall flows

2003 ◽  
Vol 217 (4) ◽  
pp. 433-441 ◽  
Author(s):  
E. Rosa de la Blanco ◽  
H. P. Hodson ◽  
R Vazquez ◽  
D Torre
Keyword(s):  
Boundary Layer ◽  
Static Pressure ◽  
Separation Bubble ◽  
Turbine Blades ◽  
The State ◽  
Linear Cascade ◽  
Surface Separation ◽  
Pressure Surface ◽  
Passage Vortex ◽  
Lp Turbine

This paper describes the effect of the state of the inlet boundary layer (laminar or turbulent) on the structure of the endwall flow on two different profiles of low-pressure (LP) turbine blades (solid thin and hollow thick). At present the state of the endwall boundary layer at the inlet of a real LP turbine is not known. The intention of this paper is to show that, for different designs of LP turbine, the state of the inlet boundary layer affects the performance of the blade in very different ways. The testing was completed at low speed in a linear cascade using area traversing, flow visualization and static pressure measurements. The paper shows that, for a laminar inlet boundary layer the two profiles have a similar loss distribution and structure of endwall flow. However, for a turbulent inlet boundary layer the two profiles are shown to differ significantly in both the total loss and endwall flow structure. The pressure side separation bubble on the solid thin profile is shown to interact with the passage vortex, causing a higher endwall loss than that measured on the hollow thick profile.

Effects of Upstream Platform Geometry on the Endwall Flows of a Turbine Cascade

2005 ◽  
Author(s):  
Elena de la Rosa Blanco ◽  
H. P. Hodson ◽  
R. Va´zquez
Keyword(s):  
Boundary Layer ◽  
Separation Bubble ◽  
Turbine Cascade ◽  
Blade Profile ◽  
Linear Cascade ◽  
Surface Separation ◽  
Pressure Surface ◽  
Low Pressure Turbine ◽  
Large Pressure ◽  
Blade Row

This paper describes the effect that the endwall geometry has on the endwall flows in the vicinity of the blade platform in a low-pressure turbine. The aim of this work is to assess the effect on blade performance of a step in hub diameter just ahead of the blade row. The blade profile under consideration is of high aspect ratio and characterized by a large pressure surface separation bubble. The tests are conducted on a linear cascade and the experimental results are supported by numerical simulations. Two different steps are employed, i.e., forward facing and backward facing steps. Furthermore, the size of the step and the thickness of the inlet endwall boundary layer are also varied. It was found that the presence of the step ahead of the blade row can significantly alter the structure and the strength of the endwall flows. A backward facing step gives rise to lower losses when compared with a flat endwall. However, the effect is found to be dependent on the step height and the thickness of the approaching boundary layer. A forward facing step, on the other hand, produces higher losses than a flat endwall.

Endwall Boundary Layer Development in an Engine Representative Four-Stage Low Pressure Turbine Rig

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Maria Vera ◽  
Elena de la Rosa Blanco ◽  
Howard Hodson ◽  
Raul Vazquez
Keyword(s):  
Boundary Layer ◽  
Leading Edge ◽  
Low Pressure ◽  
The State ◽  
Linear Cascade ◽  
Low Speed ◽  
Cold Flow ◽  
Low Pressure Turbine ◽  
Transitional Boundary Layer ◽  
Passage Vortex

Research by de la Rosa Blanco et al. (“Influence of the State of the Inlet Endwall Boundary Layer on the Interaction Between the Pressure Surface Separation and the Endwall Flows,” Proc. Inst. Mech. Eng., Part A, 217, pp. 433–441) in a linear cascade of low pressure turbine (LPT) blades has shown that the position and strength of the vortices forming the endwall flows depend on the state of the inlet endwall boundary layer, i.e., whether it is laminar or turbulent. This determines, amongst other effects, the location where the inlet boundary layer rolls up into a passage vortex, the amount of fluid that is entrained into the passage vortex, and the interaction of the vortex with the pressure side separation bubble. As a consequence, the mass-averaged stagnation pressure loss and therefore the design of a LPT depend on the state of the inlet endwall boundary layer. Unfortunately, the state of the boundary layer along the hub and casing under realistic engine conditions is not known. The results presented in this paper are taken from hot-film measurements performed on the casing of the fourth stage of the nozzle guide vanes of the cold flow affordable near term low emission (ANTLE) LPT rig. These results are compared with those from a low speed linear cascade of similar LPT blades. In the four-stage LPT rig, a transitional boundary layer has been found on the platforms upstream of the leading edge of the blades. The boundary layer is more turbulent near the leading edge of the blade and for higher Reynolds numbers. Within the passage, for both the cold flow four-stage rig and the low speed linear cascade, the new inlet boundary layer formed behind the pressure leg of the horseshoe vortex is a transitional boundary layer. The transition process progresses from the pressure to the suction surface of the passage in the direction of the secondary flow.

Actuated Transition in an LP Turbine Laminar Separation: An Experimental Approach

2011 ◽  
Author(s):  
Jenny Baumann ◽  
Ulrich Rist ◽  
Martin Rose ◽  
Tobias Ries ◽  
Stephan Staudacher
Keyword(s):  
Boundary Layer ◽  
Separation Bubble ◽  
Turbine Blades ◽  
Reynolds Numbers ◽  
Experimental Investigations ◽  
Stream Velocity ◽  
Laminar Separation ◽  
Low Reynolds Numbers ◽  
Low Reynolds ◽  
Lp Turbine

The reduction of blade counts in the LP turbine is one possibility to cut down weight and therewith costs. At low Reynolds numbers the suction side laminar boundary layer of high lift LP turbine blades tends to separate and hence cause losses in turbine performance. To limit these losses, the control of laminar separation bubbles has been the subject of many studies in recent years. A project is underway at the University of Stuttgart that aims to suppress laminar separation at low Reynolds numbers (60,000) by means of actuated transition. In an experiment a separating flow is influenced by disturbances, small in amplitude and of a certain frequency, which are introduced upstream of the separation point. Small existing disturbances are therewith amplified, leading to earlier transition and a more stable boundary layer. The separation bubble thus gets smaller without need of a high air mass flow as for steady blowing or pulsed vortex generating jets. Frequency and amplitude are the parameters of actuation. The non-dimensional actuation frequency is varied from 0.2 to 0.5, whereas the normalized amplitude is altered between 5, 10 and 25% of the free stream velocity. Experimental investigations are made by means of PIV and hot wire measurements. Disturbed flow fields will be compared to an undisturbed one. The effectiveness of the presented boundary layer control will be compared to those of conventional ones. Phase-logged data will give an impression of the physical processes in the actuated flow.

Loss reduction on ultra high lift low-pressure turbine blades using selective roughness and wake unsteadiness

2007 ◽  
Vol 111 (1118) ◽  
pp. 257-266 ◽  
Author(s):  
R. J. Howell ◽  
K. M. Roman
Keyword(s):  
Boundary Layer ◽  
Steady Flow ◽  
Separation Bubble ◽  
Turbine Blades ◽  
Low Pressure ◽  
Surface Boundary ◽  
Suction Surface ◽  
High Lift ◽  
Profile Losses ◽  
Lp Turbine

This paper describes how it is possible to reduce the profile losses on ultra high lift low pressure (LP) turbine blade profiles with the application of selected surface roughness and wake unsteadiness. Over the past several years, an understanding of wake interactions with the suction surface boundary layer on LP turbines has allowed the design of blades with ever increasing levels of lift. Under steady flow conditions, ultra high lift profiles would have large (and possibly open) separation bubbles present on the suction side which result from the very high diffusion levels. The separation bubble losses produced by it are reduced when unsteady wake flows are present. However, LP turbine blades have now reached a level of loading and diffusion where profile losses can no longer be controlled by wake unsteadiness alone. The ultra high lift profiles investigated here were created by attaching a flap to the trailing edge of another blade in a linear cascade — the so called flap-test technique. The experimental set-up used in this investigation allows for the simulation of upstream wakes by using a moving bar system. Hotwire and hotfilm measurements were used to obtain information about the boundary-layer state on the suction surface of the blade as it evolved in time. Measurements were taken at a Reynolds numbers ranging between 100,000 and 210,000. Two types of ultra high lift profile were investigated; ultra high lift and extended ultra high lift, where the latter has 25% greater back surface diffusion as well as a 12% increase in lift compared to the former. Results revealed that distributed roughness reduced the size of the separation bubble with steady flow. When wakes were present, the distributed roughness amplified disturbances in the boundary layer allowing for more rapid wake induced transition to take place, which tended to eliminate the separation bubble under the wake. The extended ultra high lift profile generated only slightly higher losses than the original ultra high lift profile, but more importantly it generated 12% greater lift.

Unsteady Flow in Oscillating Turbine Cascade: Part 1 — Linear Cascade Experiment

1996 ◽  
Author(s):  
L. He
Keyword(s):  
Computational Study ◽  
Separation Bubble ◽  
Turbine Blades ◽  
Leading Edge ◽  
Computational Method ◽  
Reattachment Point ◽  
Suction Surface ◽  
Linear Cascade ◽  
Unsteady Pressure ◽  
Pressure Surface

An experimental and computational study has been carried out on a linear cascade of low pressure turbine blades with the middle blade oscillating in a torsion mode. The main objectives of the present work were to enhance understanding of the behaviour of bubble type of flow separation and to examine the predictive ability of a computational method. In addition, an attempt was made to address a general modelling issue: was the linear assumption adequately valid for such kind of flow? In Part 1 of this paper, the experimental work was described. Unsteady pressure was measured along blade surfaces using off-board mounted pressure transducers at realistic reduced frequency conditions. A short separation bubble on the suction surface near the trailing edge and a long leading-edge separation bubble on the pressure surface were identified. It was found that in the regions of separation bubbles, unsteady pressure was largely influenced by the movement of reattachment point, featured by an abrupt phase shift and an amplitude trough in the 1st harmonic distribution. The short bubble on the suction surface seemed to follow closely a laminar bubble transition model in a quasi-steady manner, and had a localized effect. The leading-edge long bubble on the pressure surface, on the other hand, was featured by a large movement of the reattachment point, which affected the surface unsteady pressure distribution substantially. As far as the aerodynamic damping was concerned, there was a destabilizing effect in the separated flow region, which was however largely balanced by the stabilizing effect downstream of the reattachment point due to the abrupt phase change.

Pressure Surface Separations in Low Pressure Turbines: Part 2 of 2 — Interactions With the Secondary Flow

2001 ◽  
Author(s):  
Michael J. Brear ◽  
Howard P. Hodson ◽  
Paloma Gonzalez ◽  
Neil W. Harvey
Keyword(s):  
Secondary Flow ◽  
Turbine Blades ◽  
Low Pressure ◽  
Secondary Flows ◽  
Suction Surface ◽  
Linear Cascade ◽  
Surface Separation ◽  
Pressure Surface ◽  
Low Pressure Turbine ◽  
Turbine Design

This paper describes a study of the interaction between the pressure surface separation and the secondary flow on low pressure turbine blades. It is found that this interaction can significantly affect the strength of the secondary flow and the loss that it creates. Experimental and numerical techniques are used to study the secondary flow in a family of four low pressure turbine blades in linear cascade. These blades are typical of current designs, share the same suction surface and pitch, but have differing pressure surfaces. A mechanism for the interaction between the pressure surface separation and the secondary flow is proposed and is used to explain the variations in the secondary flows of the four blades. This mechanism is based on simple dynamical secondary flow concepts and is similar to the aft-loading argument commonly used in modern turbine design.

The Transition Mechanism of Highly-Loaded LP Turbine Blades

2003 ◽  
Author(s):  
R. D. Stieger ◽  
H. P. Hodson
Keyword(s):  
Boundary Layer ◽  
Shear Layer ◽  
Separation Bubble ◽  
Turbine Blades ◽  
Suction Surface ◽  
Transition Mechanism ◽  
Separated Shear Layer ◽  
Lp Turbine ◽  
Laminar Shear ◽  
Highly Loaded

A detailed experimental investigation was conducted into the interaction of a convected wake and a separation bubble on the rear suction surface of a highly loaded low-pressure (LP) turbine blade. Boundary layer measurements, made with 2D LDA, revealed a new transition mechanism resulting from this interaction. Prior to the arrival of the wake, the boundary layer profiles in the separation region are inflexional. The perturbation of the separated shear layer caused by the convecting wake causes an inviscid Kelvin-Helmholtz rollup of the shear layer. This results in the breakdown of the laminar shear layer and a rapid wake-induced transition in the separated shear layer.

The Transition Mechanism of Highly Loaded Low-Pressure Turbine Blades

2004 ◽  
Vol 126 (4) ◽  
pp. 536-543 ◽  
Author(s):  
R. D. Stieger ◽  
H. P. Hodson
Keyword(s):  
Boundary Layer ◽  
Shear Layer ◽  
Separation Bubble ◽  
Turbine Blades ◽  
Low Pressure ◽  
Suction Surface ◽  
Transition Mechanism ◽  
Separated Shear Layer ◽  
Lp Turbine ◽  
Highly Loaded

A detailed experimental investigation was conducted into the interaction of a convected wake and a separation bubble on the rear suction surface of a highly loaded low-pressure (LP) turbine blade. Boundary layer measurements, made with 2D LDA, revealed a new transition mechanism resulting from this interaction. Prior to the arrival of the wake, the boundary layer profiles in the separation region are inflexional. The perturbation of the separated shear layer caused by the convecting wake causes an inviscid Kelvin-Helmholtz rollup of the shear layer. This results in the breakdown of the laminar shear layer and a rapid wake-induced transition in the separated shear layer.

Unsteady Flow in Oscillating Turbine Cascades: Part 1—Linear Cascade Experiment

1998 ◽  
Vol 120 (2) ◽  
pp. 262-268 ◽  
Author(s):  
L. He
Keyword(s):  
Computational Study ◽  
Separation Bubble ◽  
Turbine Blades ◽  
Leading Edge ◽  
Computational Method ◽  
Reattachment Point ◽  
Suction Surface ◽  
Linear Cascade ◽  
Unsteady Pressure ◽  
Pressure Surface

An experimental and computational study has been carried out on a linear cascade of low-pressure turbine blades with the middle blade oscillating in a torsion mode. The main objectives of the present work were to enhance understanding of the behavior of bubble-type flow separation and to examine the predictive ability of a computational method. In addition, an attempt was made to address a general modeling issue: Was the linear assumption adequately valid for such kind of flow? In Part 1 of this paper, the experimental work is described. Unsteady pressure was measured along blade surfaces using off-board mounted pressure transducers at realistic reduced frequency conditions. A short separation bubble on the suction surface near the trailing edge and a long leading-edge separation bubble on the pressure surface were identified. It was found that in the regions of separation bubbles, unsteady pressure was largely influenced by the movement of reattachment point, featured by an abrupt phase shift and an amplitude trough in the first harmonic distribution. The short bubble on the suction surface seemed to follow closely a laminar bubble transition model in a quasi-steady manner, and had a localized effect. The leading-edge long bubble on the pressure surface, on the other hand, was featured by a large movement of the reattachment point, which affected the surface unsteady pressure distribution substantially. As far as the aerodynamic damping was concerned, there was a destabilizing effect in the separated flow region, which was, however, largely balanced by the stabilizing effect downstream of the reattachment point due to the abrupt phase change.

Pressure Surface Separations in Low-Pressure Turbines—Part 2: Interactions With the Secondary Flow

2002 ◽  
Vol 124 (3) ◽  
pp. 402-409 ◽  
Author(s):  
Michael J. Brear ◽  
Howard P. Hodson ◽  
Paloma Gonzalez ◽  
Neil W. Harvey
Keyword(s):  
Secondary Flow ◽  
Turbine Blades ◽  
Low Pressure ◽  
Secondary Flows ◽  
Suction Surface ◽  
Linear Cascade ◽  
Surface Separation ◽  
Pressure Surface ◽  
Low Pressure Turbine ◽  
Turbine Design

This paper describes a study of the interaction between the pressure surface separation and the secondary flow on low-pressure turbine blades. It is found that this interaction can significantly affect the strength of the secondary flow and the loss that it creates. Experimental and numerical techniques are used to study the secondary flow in a family of four low-pressure turbine blades in linear cascade. These blades are typical of current designs, share the same suction surface and pitch, but have differing pressure surfaces. A mechanism for the interaction between the pressure surface separation and the secondary flow is proposed and is used to explain the variations in the secondary flows of the four blades. This mechanism is based on simple dynamical secondary flow concepts and is similar to the aft-loading argument commonly used in modern turbine design.

Sign in / Sign up

Export Citation Format

Share Document