Far-field impulse response verification of selected high-frequency optics backscattering analogs

1975 ◽  
Vol 14 (9) ◽  
pp. 2169 ◽  
Author(s):  
J. J. Stephens ◽  
Peter S. Ray ◽  
T. W. Kitterman
1982 ◽  
Vol 72 (4) ◽  
pp. 1049-1068
Author(s):  
John Boatwright

abstract A model for the far-field acceleration radiated by an incoherent rupture is constructed by combining Madariaga's (1977) theory for the high-frequency radiation from crack models of faulting with a simple statistical source model. By extending Madariaga's results to acceleration pulses with finite durations, the peak acceleration of a pulse radiated by a single stop or start of a crack tip is shown to depend on the dynamic stress drop of the subevent, the total change in rupture velocity, and the ratio of the subevent radius to the acceleration pulse width. An incoherent rupture is approximated by a sample from a self-similar distribution of coherent subevents. Assuming the subevents fit together without overlapping, the high-frequency level of the acceleration spectra depends linearly on the rms dynamic stress drop, the average change in rupture velocity, and the square root of the overall rupture area. The high-frequency level is independent, to first order, of the rupture complexity. Following Hanks (1979), simple approximations are derived for the relation between the rms dynamic stress drop and the rms acceleration, averaged over the pulse duration. This relation necessarily depends on the shape of the body-wave spectra. The body waves radiated by 10 small earthquakes near Monticello Dam, South Carolina, are analyzed to test these results. The average change of rupture velocity of Δv = 0.8β associated with the radiation of the acceleration pulses is estimated by comparing the rms acceleration contained in the P waves to that in the S waves. The rms dynamic stress drops of the 10 events, estimated from the rms accelerations, range from 0.4 to 1.9 bars and are strongly correlated with estimates of the apparent stress.


Author(s):  
Andrew L. Bodling ◽  
Anupam Sharma

A study was done to investigate how boundary layer tripping mechanisms can affect the ability of a permeable surface FW-H solver to predict the far field noise emanating from an airfoil trailing edge. The far field noise in a baseline airfoil as well as the baseline airfoil fitted with fin let fences was analyzed. Two numerical boundary layer tripping mechanisms were implemented. The results illustrated the importance of choosing a permeable integration surface that is outside any high frequency waves emanating from the trip region. The results also illustrated the importance of choosing a boundary layer tripping mechanism that minimizes any extraneous noise so that an integration surface can be taken close to the airfoil.


2021 ◽  
Vol 1 (2) ◽  
pp. 1-5
Author(s):  
Mengzi Li ◽  
◽  
Shishan Wang ◽  
Jian Guo

The miniaturization and integration of Switching Mode Power Supply (SMPS) is increasing, making it more complicated to analyze and predict its far-field radiated emission, and, consequently, studying the suppression method of far-field radiated emission of SMPS is of practical significance and engineering value. In this paper, a high-frequency SMPS is selected as the research object, whose far-field radiated emission is measured under the condition of three typical suppression methods. The experimental results verified the effectiveness of common-mode inductor and are of reference value for EMC design of power converter. Keywords: SMPS; EMC; Far-field Radiated Emission;


2016 ◽  
Vol 25 (02) ◽  
pp. 1750002 ◽  
Author(s):  
Shiquan Wang

This paper investigates the prediction of the far-field performances of high frequency projectors using the second source array method (SSAM). The far-field parameters can be calculated accurately using the complex acoustic pressure data of two very close parallel planes which lie in the near-field region of the projector. The paper simulates the feasibility of predicting the far-field parameters such as transmitting voltage response and the far-field directivity pattern. The predicting results are compared with that calculated using boundary element method (BEM). It shows very good agreement between the two methods. A planar high frequency projector is measured using the near-field method. In order to verify the predicting results, the far-field measurement is performed for the same projector. The comparison of the results shows that the near-field method is capable to precisely predict the far-field parameters of the projector.


Sign in / Sign up

Export Citation Format

Share Document