A New Validated Stability Indicating RP-HPLC Method for the Quantification of Allopurinol and Lesinurad in Bulk and Pharmaceutical Formulations

2020 ◽  
Vol 5 (1) ◽  
pp. 51-55
Author(s):  
K.V. Ramanjaneyulu ◽  
K. Venkata Ramana ◽  
M. Prasada Rao
Keyword(s):  
Degradation Products ◽  
Pharmaceutical Formulations ◽  
Hplc Method ◽  
Forced Degradation ◽  
Analysis Method ◽  
Degradation Study ◽  
Stability Indicating ◽  
Stress Study ◽  
Isocratic Hplc ◽  
Bulk Drug

The objective of this study was to develop and validate a method for simultaneous quantitative analysis of allopurinol and lesinurad in bulk drug and pharmaceutical formulations. An isocratic HPLC analysis method using a reverse phase Waters spherisorb ODS1 C18 column (250 mm × 4.6 mm, 5 μ) and a simple mobile phase without buffer was developed, optimized and fully validated. Analyses were carried out at a flow rate of 0.9 mL/min at 50 °C and monitored at 246 nm. This HPLC method exhibited good linearity, accuracy and selectivity. The recovery (accuracy) of both allopurinol and lesinurad from all matrices was greater than 98 %. The allopurinol and lesinurad peak detected in the samples of a forced degradation study and no interference of excepients or the degradation products formed during stress study. The method was rugged with good intra- and inter-day precision and sensitive. This stability indicating HPLC method was selective, accurate and precise for the simultaneous analysis of allopurinol and lesinurad in pharmaceutical formulations.

scholarly journals Development and validation of a novel stability indicating HPLC method for the separation and determination of darolutamide and its impurities in pharmaceutical formulations

2021 ◽  
Vol 104 (4) ◽  
pp. 57-68
Author(s):  
V.G. Kamani ◽  
◽  
M. Sujatha ◽  
G.B. Daddala ◽  
◽  
...  
Keyword(s):  
Ammonium Acetate ◽  
Pharmaceutical Formulations ◽  
Hplc Method ◽  
Forced Degradation ◽  
Degradation Study ◽  
Stability Indicating ◽  
System Suitability ◽  
Development And Validation ◽  
First Time

This study reports for the first time about a stability indicating RP-HPLC method for analysis of darolutamide and its impurities 1, 2, and 3 in bulk and formulations. The separation was achieved on Phenomenex column with Luna C18 (250 mm × 4.6 mm, 5 μm) as stationary phase, and 50 mM ammonium acetate: methanol solution 15:80 (v/v) at pH 5.2 as mobile phase at 1.0 mL/min flow rate. UV detection was carried at wavelength of 239 nm. In these conditions the retention time of darolutamide and its impurities 1, 2, and 3 was 7.05, 8.90, 4.63 and 5.95 min, respectively. The method was validated for system suitability, range of analysis, precision, specificity, stability, and robustness. Forced degradation study was done through exposure of the analyte to five different stress conditions and the % degradation was small in all degradation condition. The proposed method can separate and estimate the drug and its impurities in pharmaceutical formulations. Hence, the developed method was suitable for the quantification of darolutamide and can separate and analyse impurities 1, 2, and 3

scholarly journals Development of Stability Indicating RP-HPLC Method for Ertapenem in Bulk Drug and Pharmaceutical Dosage Form

2017 ◽  
Vol 16 (1) ◽  
pp. 21-28
Author(s):  
Ruchi Jain ◽  
Nilesh Jain ◽  
Deepak Kumar Jain ◽  
Avineesh Singh ◽  
Surendra Kumar Jain
Keyword(s):  
Dosage Form ◽  
Degradation Products ◽  
Hplc Method ◽  
Stress Conditions ◽  
Assay Method ◽  
Main Peak ◽  
Forced Degradation ◽  
Pharmaceutical Dosage Form ◽  
Stability Indicating ◽  
Bulk Drug

A simple, inexpensive, rapid and novel stability indicating isocratic HPLC method has been developed and validated for quantitative analysis of ertapenem sodium in the bulk drug and in pharmaceutical dosage form. An isocratic separation of ertapenem sodium was achieved on Hypersil BDS C18 column (4.6 x 250 mm, 5 ? particle size) as the stationary phase with a flow rate of 1.2 ml/min and using a UV detector to monitor the eluate at 298 nm. The mobile phase consisted of acetonitrile : water (60:40v/v) and pH adjusted 2.9 by othophosphoric acid enabled separation of the drug from its degradation products. The method was validated for linearity, accuracy (recovery), precision, specificity and robustness. The linearity of the method was satisfactory over the range 2-10 ?g/ml (correlation coefficient 0.999). Recovery of ertapenem sodium from the pharmaceutical dosage form ranged from 99.97 to 103.7%. Ertapenem sodium was subjected to stress conditions [hydrolysis (acid, base), oxidation, photolysis and thermal degradation] and the samples were analyzed by this method. The forceddegradation study with ertapenem sodium showed that it was degraded under basic condition. The drug was stable under the other stress conditions investigated. Ertapenem sodium was found to be less stable in solution state, whereas it was comparatively much stable in solid state. The degradation products were well resolved from main peak. The forced degradation study prove the stability indicating power of the method and therefore, the validated method may be useful for routine analysis of ertapenem sodium as bulk drug, in respective dosage forms, for dissolution studies and as stability indicating assay method in pharmaceutical laboratories and industries.Dhaka Univ. J. Pharm. Sci. 16(1): 21-28, 2017 (June)

STABILITY INDICATING RP-HPLC METHOD FOR SEPARATION AND QUANTIFICATION OF RELATED SUBSTANCES OF TICLOPIDINE IN BULK AND PHARMACEUTICAL FORMULATIONS

INDIAN DRUGS ◽  
2021 ◽  
Vol 58 (08) ◽  
pp. 75-78
Author(s):  
B. S. Venkateswarlu ◽  
Prudhvi N. Sai ◽  
Keyword(s):  
Degradation Products ◽  
Pharmaceutical Formulations ◽  
Hplc Method ◽  
Standard Drug ◽  
Stability Indicating ◽  
Stress Studies ◽  
Related Substances ◽  
Stability Indicating Method ◽  
Stress Degradation ◽  
Bulk Drug

A simple, specific, accurate and stable reverse phase liquid chromatographic method was developed for the simultaneous determination of ticlopidine and its related impurities A and B in bulk drug and tablet dosage forms. The analysis has been performed on XTerra C18 column (250 mm×4.6 mm; 5 µ id) and mobile phase containing of methanol and pH 6.8 phosphate buffer in the ratio of 80:20 (V/V). The detection was carried at 228 nm with a flow rate of 1.0 mL/min. The retention times were found to be 8.9, 5.98 and 4.62 min for ticlopidine, impurities A and B, respectively. The method was validated according to ICH guidelines. The method was validated for specificity, precision, linearity, accuracy and robustness. The linearity range of 50-200 µg/mL for ticlopidine and 0.5-2.0 µg/mL for impurity A and B. The recoveries of ticlopidine and impurities were found to be within the range of 98-102 and the % RSD in each spiked level was found to be less than 2. The stress degradation studies confirmed that the method was effectively separate the degradation products and impurities formed in the stress studies and hence the method was found to be stability indicating method. The method can effectively quantify the standard drug ticlopidine and its impurities A and B in bulk drug and pharmaceutical formulations.

Synthesis and Characterization of Potential and Degraded Impurities of Regadenoson

2020 ◽  
Vol 16 (8) ◽  
pp. 1130-1139
Author(s):  
Singaram Sathiyanarayanan ◽  
Chidambaram Subramanian Venkatesan ◽  
Senthamaraikannan Kabilan
Keyword(s):  
Mass Spectra ◽  
Degradation Products ◽  
Hplc Method ◽  
Forced Degradation ◽  
Spectroscopic Techniques ◽  
A2a Adenosine Receptor ◽  
Degradation Study ◽  
Related Substances ◽  
Adenosine Receptor Agonist

Background: Regadenoson is an A2A adenosine receptor agonist that is a coronary vasodilator and commonly used as a pharmacologic cardiac stressing agents. Methods: HPLC method was used for the analysis of related substances. The degraded impurities during the process were isolated and characterized by IR, Mass and NMR spectral analysis. Results: Forced degradation study of regadenoson under conditions of hydrolysis (neutral, acidic and alkaline) and oxidations suggested in the ICH Q1A(R2) was accomplished. The drug showed significant degradation under all the above conditions. On the whole, five novel degradation products were found under diverse conditions along with process related impurities which were not reported earlier. Conclusion: All the degradation products were well characterized by using advanced spectroscopic techniques like IR, 1H NMR, 13C NMR and Mass spectra. The identification of these impurities will be productive for the quality control during the production and stability behavior of the regadenoson drug substance.

Identification, Characterization, and Quantification of Impurities of Safinamide Mesilate: Process-Related Impurities and Degradation Products

2017 ◽  
Vol 100 (4) ◽  
pp. 1029-1037 ◽  
Author(s):  
Liang Zou ◽  
Lili Sun ◽  
Hui Zhang ◽  
Wenkai Hui ◽  
Qiaogen Zou ◽  
...  
Keyword(s):  
Degradation Products ◽  
Hplc Method ◽  
Formation Mechanisms ◽  
Stability Indicating ◽  
Related Impurities ◽  
Related Substances ◽  
Water Ph ◽  
Bulk Drug ◽  
First Time

Abstract The characterization of process-related impurities and degradation products of safinamide mesilate (SAFM) in bulk drug and a stability-indicating HPLC method for the separation and quantification of all the impurities were investigated. Four process-related impurities (Imp-B, Imp-C, Imp-D, and Imp-E) were found in the SAFM bulk drug. Five degradation products (Imp-A, Imp-C, Imp-D, Imp-E, and Imp-F) were observed in SAFM under oxidative conditions. Imp-C, Imp-D, and Imp-E were also degradation products and process-related impurities. Remarkably, one new compound, identified as (S)-2-[4-(3-fluoro-benzyloxy) benzamido] propanamide (i.e., Imp-D), is being reported here as an impurity for the first time. Furthermore, the structures of the aforementioned impurities were characterized and confirmed via IR, NMR, and MS techniques, and the most probable formation mechanisms of all impurities proposed according to the synthesis route. Optimum separation was achieved on an Inertsil ODS-3 column (250 × 4.6 mm, 5 μm), using 0.1% formic acid in water (pH adjusted to 5.0) and acetonitrile as the mobile phase in gradient mode. The proposed method was found to be stability-indicating, precise, linear, accurate, sensitive, and robust for the quantitation of SAFM and its process-related substances, including its degradation products.

scholarly journals Validated Stability Indicating RP-HPLC Method for Simultaneous Estimation of Codeine Phosphate and Chlorpheniramine Maleate from Their Combined Liquid Dosage Form

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
Ramakrishna Kommana ◽  
Praveen Basappa
Keyword(s):  
Limit Of Detection ◽  
Degradation Products ◽  
Hplc Method ◽  
Simultaneous Estimation ◽  
Forced Degradation ◽  
Codeine Phosphate ◽  
Chlorpheniramine Maleate ◽  
Combination Drug ◽  
Stability Indicating ◽  
Rp Hplc

The present paper describes the development of quick stability indicating RP-HPLC method for the simultaneous estimation of codeine phosphate and chlorpheniramine maleate in the presence of its degradation products, generated from forced degradation studies. The developed method separates codeine phosphate and chlorpheniramine maleate in impurities/degradation products. Codeine phosphate and chlorpheniramine maleate and their combination drug product were exposed to acid, base, oxidation, dry heat, and photolytic stress conditions, and the stressed samples were analysed by proposed method. The proposed HPLC method utilizes the Shimadzu HPLC system on a Phenomenex C18 column (, 5 μ) using a mixture of 1% o-phosphoric acid in water : acetonitrile : methanol (78 : 10 : 12) mobile phase with pH adjusted to 3.0 in an isocratic elution mode at a flow rate of 1 mL/min, at 23°C with a load of 20 μL. The detection was carried out at 254 nm. The retention time of codeine phosphate and chlorpheniramine maleate was found to be around 3.47 min and 9.45 min, respectively. The method has been validated with respect to linearity, robustness, precision, accuracy, limit of detection (LOD), and limit of quantification (LOQ). The developed validated stability indicating HPLC method was found to be simple, accurate, and reproducible for the determination of instability of these drugs in bulk and commercial products.

scholarly journals STABILITY INDICATING HPLC METHOD FOR DETERMINATION OF VILAZODONE HYDROCHLORIDE

2017 ◽  
Vol 9 (4) ◽  
pp. 123
Author(s):  
Birva A. Athavia ◽  
Zarna R. Dedania ◽  
Ronak R. Dedania ◽  
S. M. Vijayendra Swamy ◽  
Chetana B. Prajapati
Keyword(s):  
Limit Of Detection ◽  
Degradation Products ◽  
Hplc Method ◽  
Alkaline Condition ◽  
Forced Degradation ◽  
Molecular Formula ◽  
Stability Indicating ◽  
Dry Heat ◽  
Limit Of Quantitation

Objective: The aim and objective of this study was to develop and validate Stability Indicating HPLC method for determination of Vilazodone Hydrochloride.Methods: The method was carried out on a Phenomenex, C18 (250x4.6 mm, 5 µm) Column using a mixture of Acetonitrile: Water (50:50v/v), pH adjusted to 3.3 with Glacial Acetic Acid for separation. The flow rate was adjusted at 1 ml/min and Detection was carried out at 240 nm.Results: The retention time of vilazodone hydrochloride was found to be 2.3 min. The calibration curve was found to be linear in the range 25-75µg/ml with a correlation coefficient (R2=0.996). The limit of detection and limit of quantitation were found to be 4.78µg/ml and 14.48µg/ml respectively. The % recovery of vilazodone hydrochloride was found to be in the range of 98.21±0.08 % to 99.07±0.64%. The proposed method was successfully applied for the estimation of vilazodone hydrochloride in marketed tablet formulation.Vilazodone Hydrochloride was subjected to forced degradation under Acidic, Alkaline, Oxidation, Dry Heat and Photolytic degradation conditions. Vilazodone hydrochloride showed 3.12% degradation under acidic condition, 4.78% under alkaline condition, 7.8% under oxidation condition, 3.53% under dry heat condition and 4.9% under photolytic condition.Acid degradation impurity was identified and characterised by LC-MS/MS was found to be 1-(4-Penten-1-yl) piperazine having molecular weight 154.253 (m/z 155.08) and Molecular Formula C9H18N2.Conclusion: A simple, precise, rapid and accurate Stability Indicating HPLC method has been developed and validated for the determination of Vilazodone Hydrochloride in presence of its degradation products as per the ICH Guidelines. 

Concurrent Determination of Daclatasvir and Sofosbuvir in Pure Binary Mixture and Their Combined Film Coated Tablets by a Simple Stability Indicating RP-HPLC Method

2021 ◽  
pp. 5913-5918
Author(s):  
Ramreddy Godela ◽  
Sowjanya G
Keyword(s):  
Degradation Products ◽  
Hplc Method ◽  
Forced Degradation ◽  
Good Resolution ◽  
Stability Indicating ◽  
Extreme Stress ◽  
Rp Hplc ◽  
Highly Sensitive ◽  
Validation Parameters ◽  
Acid And Base

A trouble-free, simple, specific and highly sensitive stability indicating phase HPLC method was developed for concurrent assessment of Daclatasvir and Sofosbuvir in pure and in their combined tablet formulation. An effectual separation was accomplished by using XDB Phenyl (250 x 4.6mm, 5µ,100 A0) column, mobile phase composition of Acetonitrile: buffer(0.1%v/v Trifluoroaceticacid in water) (50:50 v/v) and isocratic elution at a flow rate of 1ml/min and detection wavelength of 275nm. The extreme stress conditions like hydrolysis with acid and base, peroxide oxidation, thermal decomposition were used as per ICH specifications to assess the stability of the analytes in bulk and dosage forms. The retention times of Daclatasvir and Sofosbuvir were found at 2.8 and 3.7min respectively. The proposed method has linear response in the concentration ranges from 12 to 36µg/ml and 80 to 240 µg/ml for Daclatasvir and Sofosbuvir respectively. The detection and quantification limits calculated as 2.5μg/ml and 7.8μg/ml for DCL, 5.2μg/ml and 15.8μg/ml SOF respectively. All the method validation parameters were met the acceptance limits of Q2 specifications of ICH procedures. The degradation products produced by forced degradation studies were have good resolution from Daclatasir and Sofosbuvir peaks, which represents the methods stability. The proposed RP-HPLC method was highly sensitive, precise, stability indicating and economical. That’s why the method has the capacity to employ in the pharmaceutical manufacturing of Daclatasvir and Sofosbuvir and routine analysis in quality control department.

Sign in / Sign up

Export Citation Format

Share Document