scholarly journals INFLUENCE OF WATER-TO-CEMENT RATIO ON THE RATE OF COMPRESSIVE STRENGTH DEVELOPMENT UNDER SUPERCRITICAL CO2 CONDITION

2016 ◽  
Vol 70 (1) ◽  
pp. 268-274
Author(s):  
Nozomi IWAYA ◽  
Tetsuya ISHIDA
Keyword(s):  
Compressive Strength ◽  
Strength Development ◽  
Cement Ratio ◽  
Water To Cement Ratio ◽  
Influence Of Water ◽  
Compressive Strength Development

scholarly journals Strength Development of Pervious Concrete with various Aggregate/Cement Ratio

2019 ◽  
Vol 9 (2S2) ◽  
pp. 1-3
Keyword(s):  
Compressive Strength ◽  
Pervious Concrete ◽  
Strength Development ◽  
Cement Ratio ◽  
Compressive Strength Development

This paper evaluates the effect of aggregate/cement ratio on the strength development of pervious concrete. To evaluate this study, mixture proportions have been prepared by varying the aggregate/cement ratio and studying its compressive strength development. Four different aggregate cement ratios were chosen and its strength development at 7 days and 28 days is studied. It has been observed that lesser the aggregate/cement ratio greater the strength and vice versa

Calcined Kaolin Geopolymeric Powder: Influence of Water-to-Geopolymeric Powder Ratio

2012 ◽  
Vol 548 ◽  
pp. 48-53
Author(s):  
Y.M. Liew ◽  
H. Kamarudin ◽  
A.M. Mustafa Al Bakri ◽  
M. Binhussain ◽  
Luqman Musa ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Setting Time ◽  
Sem Analysis ◽  
Cement Ratio ◽  
Water To Cement Ratio ◽  
Influence Of Water ◽  
Calcined Kaolin ◽  
Geopolymer Paste

This paper describes the synthesis of calcined kaolin geopolymeric powder from the alkaline activation of calcined kaolin followed by solidification and pulverizing process. The geopolymeric powder was used by just adding water to produce resulted geopolymer paste. In this paper, the effect of water-to-geopolymeric powder ratios on the properties of the resulted geopolymer paste was studied. This water-to-geopolymer powder ratio was similar to that of water-to-cement ratio in the case of ordinary Portland cement (OPC). However, the concept used here was based on geopolymerization process. The compressive strength, setting time and SEM analysis of the resulted geopolymer pastes were conducted. Highest strength was achieved at water-to-geopolymer powder ratio of 0.22. The resulted geopolymer paste could be handled up to 120 minutes and reached final setting after about 4 hours of setting. Microstructure showed the formation of geopolymeric gel after the addition of water to the geopolymeric powder.

scholarly journals The potential use of pumice in mine backfill

2020 ◽  
Vol 1 ◽  
Author(s):  
Mohammed A. Hefni
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Mining Industry ◽  
Strength Development ◽  
Natural Pozzolan ◽  
Mine Backfill ◽  
Natural Pozzolans ◽  
Cemented Backfill ◽  
Compressive Strength Development ◽  
Potential Use

Abstract The use of natural pozzolans in concrete applications is gaining more attention because of the associated environmental, economic, and technical benefits. In this study, reference cemented mine backfill samples were prepared using Portland cement, and experimental samples were prepared by partially replacing Portland cement with 10 or 20 wt.% fly ash as a byproduct (artificial) pozzolan or pumice as a natural pozzolan. Samples were cured for 7, 14, and 28 days to investigate uniaxial compressive strength development. Backfill samples containing 10 wt.% pumice had almost a similar compressive strength as reference samples. There is strong potential for pumice to be used in cemented backfill to minimize costs, improve backfill properties, and promote the sustainability of the mining industry.

Chloride Ingress Control and Promotion of Internal Curing in Concrete Using Superabsorbent Polymer

2021 ◽  
Vol 888 ◽  
pp. 67-75
Author(s):  
Ariel Verzosa Melendres ◽  
Napoleon Solo Dela Cruz ◽  
Araceli Magsino Monsada ◽  
Rolan Pepito Vera Cruz
Keyword(s):  
Compressive Strength ◽  
Cementitious Materials ◽  
Internal Curing ◽  
Mix Design ◽  
Chloride Ingress ◽  
Superabsorbent Polymer ◽  
Cement Slurry ◽  
Chloride Permeability ◽  
Cement Ratio ◽  
Water To Cement Ratio

Chloride ingress into concrete from the surrounding environment can result in the corrosion of the embedded steel reinforcement and cause damage to the concrete. Superabsorbent polymer (SAP) with fine particle size was incorporated into the structure of concrete for controlling the chloride ingress and improving its compressive strength via promotion of internal curing. The SAP used in this study was evaluated for its absorbency property when exposed to cementitious environment such as aqueous solution of Ca (OH)2 and cement slurry. The results were compared to that in sodium chloride solution, the environment where absorbency of most of the SAP found in the market are well studied. Results showed that although SAP absorbency decreased with increasing concentration of Ca (OH)2 and cement, the results suggest that water containing cementitious materials are able to be absorbed by SAP. Chloride ingress into 28-day cured concrete specimens were determined using Rapid Chloride Penetration Test (RCPT) method employing 60V DC driving force. Concrete samples with size of 50 mm height x 100 mm diameter were prepared using a M25 mix design with 0.4 and 0.45 water to cement ratios and different percentages of SAP such as 0.05%, 0.1% and 0.15% with respect to cement mass. Results showed that concrete with 0.15% SAP gave the best result with 14% less chloride permeability than concrete with no SAP for a 0.4 water to cement ratio. Concrete samples for compressive strength tests with size of 200 mm height x 100 mm diameter were prepared using the same mix design and percentages of SAP and cured for 28 days. Results showed that the best results for compressive strength was found at 0.1% SAP at a 0.4 water to cement ratio which can be attributed to internal curing provided by SAP.

Sign in / Sign up

Export Citation Format

Share Document