scholarly journals Stress Redistribution Near a Crack in Maraging Steel using Composite Patch

2021 ◽  
Vol 71 (6) ◽  
pp. 816-821
Author(s):  
Manash Kumar Bhadra ◽  
Vinod Gopalan
Keyword(s):  
Finite Element ◽  
Maraging Steel ◽  
Repair Process ◽  
Extended Finite Element ◽  
Adhesive Properties ◽  
Element Analysis ◽  
Damage Initiation ◽  
Composite Patch ◽  
The Finite Element Analysis ◽  
Minimal Damage

The presence of a crack significantly reduces the load bearing capacity of a structure made of fracture prone material. The conventional process of repairing a defect is gouging and filling the gouged location by rewelding. It is not only time consuming but also constrained by the number of repairs that can be done as material properties degrade with each round of rewelding. In an attempt to overcome the limitation of the conventional repair process, repairing a defect using composite patch is proposed. The study is carried out on Maraging steel (M250) and the defect considered is a crack. Stress intensity factor (SIF), being an important parameter in fracture-based design, it is evaluated in Abaqus. Extended finite element method is used to model the crack. SIF is used to predict the failure load of a surface cracked tension specimen and the same is compared with the values reported in literature. Composite patch is modelled using woven ply properties. A separate layer of adhesive is also modelled to predict the properties adhesive properties. Failure analysis of each component namely, the Maraging steel plate, the composite patch and the adhesive is carried.  It was observed that the addition of a composite patch completely nullifies the presence of a crack. The patch with thickness 1mm and woven ply properties is having minimal damage initiation and likely to survive. The adhesive properties required is also obtained from the finite element analysis.  Thus, it was observed that a composite patch with woven ply properties and thickness 1mm is able to completely nullify the effect of a crack when bonded with a suitable adhesive as predicted by the analysis.

Interactive Graphics for the Analysis of Tires

1985 ◽  
Vol 13 (3) ◽  
pp. 127-146 ◽  
Author(s):  
R. Prabhakaran
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Approximate Solutions ◽  
Interactive Graphics ◽  
Element Analysis ◽  
Analysis Process ◽  
Physical Problems ◽  
The Finite Element Analysis ◽  
Analysis Computer ◽  
Discretization Technique

Abstract The finite element method, which is a numerical discretization technique for obtaining approximate solutions to complex physical problems, is accepted in many industries as the primary tool for structural analysis. Computer graphics is an essential ingredient of the finite element analysis process. The use of interactive graphics techniques for analysis of tires is discussed in this presentation. The features and capabilities of the program used for pre- and post-processing for finite element analysis at GenCorp are included.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

Use of the Finite Element Analysis Method in Pedodontics

2018 ◽  
Vol 55 (4) ◽  
pp. 666-675
Author(s):  
Mihaela Tanase ◽  
Dan Florin Nitoi ◽  
Marina Melescanu Imre ◽  
Dorin Ionescu ◽  
Laura Raducu ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Structural Model ◽  
Analysis Method ◽  
Ansys Software ◽  
Concentrated Force ◽  
Element Analysis ◽  
Finite Element Analysis Method ◽  
The Finite Element Analysis ◽  
Solid Type

The purpose of this study was to determinate , using the Finite Element Analysis Method, the mechanical stress in a solid body , temporary molar restored with the self-curing GC material. The originality of our study consisted in using an accurate structural model and applying a concentrated force and a uniformly distributed pressure. Molar structure was meshed in a Solid Type 45 and the output data were obtained using the ANSYS software. The practical predictions can be made about the behavior of different restorations materials.

A necessary modification for the finite element analysis of cracked members detection, construction, and justification

2013 ◽  
Vol 83 (7) ◽  
pp. 1087-1096 ◽  
Author(s):  
A. Ranjbaran ◽  
H. Rousta ◽  
M. O. Ranjbaran ◽  
M. A. Ranjbaran ◽  
M. Hashemi ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Cracked Members

Modeling and experimental verification on directivity of an electret cell array loudspeaker

2012 ◽  
Vol 24 (3) ◽  
pp. 326-333 ◽  
Author(s):  
Yu-Chi Chen ◽  
Wen-Ching Ko ◽  
Han-Lung Chen ◽  
Hsu-Ching Liao ◽  
Wen-Jong Wu ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Digital Control System ◽  
Analysis Model ◽  
Cell Array ◽  
Element Analysis ◽  
Finite Element Analysis Model ◽  
The Finite Element Analysis ◽  
Directivity Characteristics

We propose a model to give us a method to investigate the characteristic three-dimensional directivity in an arbitrarily configured flexible electret-based loudspeaker. In recent years, novel electret loudspeakers have attracted much interest due to their being lightweight, paper thin, and possessing excellent mid- to high-frequency responses. Increasing or decreasing the directivity of an electret loudspeaker makes it excellent for adoption to many applications, especially for directing sound to a particular area or specific audio location. Herein, we detail a novel electret loudspeaker that possesses various directivities and is based on various structures of spacers instead of having to use multichannel amplifiers and a complicated digital control system. In order to study the directivity of an electret loudspeaker based on an array structure which can be adopted for various applications, the horizontal and vertical polar directivity characteristics as a function of frequency were simulated by a finite-element analysis model. To validate the finite-element analysis model, the beam pattern of the electret loudspeaker was measured in an anechoic room. Both the simulated and experimental results are detailed in this article to validate the various assertions related to the directivity of electret cell-based smart speakers.

scholarly journals Tentative Investigations on Reducing the Edge Effects in Pre-Polishing the Optics

2020 ◽  
Vol 10 (15) ◽  
pp. 5286
Author(s):  
Xiaolong Ke ◽  
Lei Qiu ◽  
Chunjin Wang ◽  
Zhenzhong Wang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Edge Effect ◽  
Edge Effects ◽  
Material Removal ◽  
Processing Time ◽  
Grinding Process ◽  
Element Analysis ◽  
Edge Zone ◽  
The Finite Element Analysis

The material removal depth in the pre-polishing stage of the precision optics is usually tens of microns to remove the subsurface damage and grinding marks left by the previous grinding process. This processing of the upstand edge takes a large part of the time at this stage. The purpose of this paper is to develop a method that can reduce the edge effect and largely shorten the processing time of the pre-polishing stage adopting the semirigid (SR) bonnet. The generation of the edge effect is presented based on the finite element analysis of the contact pressure at the edge zone firstly. Then, some experimentations on the edge effect are conducted, and the results proved that the SR bonnet tool can overhang the workpiece edge in the pre-polishing stage to reduce the width and height of the upstand edge to largely shorten the subsequent processing time of it. In addition, there exists a perfect overhang ratio, which generates the upstand edge with the smallest width and height, with no damage to the bonnet tool in the meantime. In addition, one combination of the pre-polishing parameters is concluded according to this method, which can be safely adopted in practical process.

Sign in / Sign up

Export Citation Format

Share Document