Optimal cutting state predictions in internal turning operation with nano-SiC/GFRE composite layered boring tools

2021 ◽  
Vol 23 (1) ◽  
pp. 1
Author(s):  
Jonnalagadda Srinivas ◽  
Bijoy Kumar Nanda ◽  
Bonda Atchuta Ganesh Yuvaraju
Keyword(s):  
Turning Operation

EFFECTS OF PCD TOOL GEOMETRY ON SURFACE ROUGHNESS OF COMPOSITE IN TURNING OPERATION WITH MAXIMUM DESIRABILITY AND MINIMUM FLANK WEAR

2017 ◽  
Vol 7 (2) ◽  
pp. 7
Author(s):  
DWIVEDI SHASHI PRAKASH ◽  
SHARMA SATPAL ◽  
MISHRA R.K. ◽  
◽  
◽  
...  
Keyword(s):  
Surface Roughness ◽  
Flank Wear ◽  
Tool Geometry ◽  
Turning Operation ◽  
Pcd Tool

COMPARATIVE ANALYSIS OF PERFORMANCE BETWEEN CONVENTIONAL CUTTING FLUIDS AND VEGETABLE GLYCERINE BASED CUTTING FLUID IN STEEL 1020 TURNING OPERATION

2017 ◽  
Author(s):  
Gustavo Fernandes ◽  
Sanderson Clayton ◽  
Bernardo Jakitsch ◽  
Luis Henrique Andrade Maia ◽  
Mariana Gomes ◽  
...  
Keyword(s):  
Comparative Analysis ◽  
Cutting Fluid ◽  
Cutting Fluids ◽  
Turning Operation ◽  
Steel 1020 ◽  
Analysis Of Performance

Experimental and Numerical Investigation into Residual Stress During Turning Operation for Stainless Steel AISI 316

2020 ◽  
Vol 38 (12A) ◽  
pp. 1862-1870
Author(s):  
Safa M. Lafta ◽  
Maan A. Tawfiq
Keyword(s):  
Stainless Steel ◽  
Residual Stresses ◽  
Orthogonal Cutting ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Percentage Error ◽  
Depth Of Cut ◽  
Main Role ◽  
Turning Operation ◽  
Aisi 316

RS (residual stresses) represent the main role in the performance of structures and machined parts. The main objective of this paper is to investigate the effect of feed rate with constant cutting speed and depth of cut on residual stresses in orthogonal cutting, using Tungsten carbide cutting tools when machining AISI 316 in turning operation. AISI 316 stainless steel was selected in experiments since it is used in many important industries such as chemical, petrochemical industries, power generation, electrical engineering, food and beverage industry. Four feed rates were selected (0.228, 0.16, 0.08 and 0.065) mm/rev when cutting speed is constant 71 mm/min and depth of cutting 2 mm. The experimental results of residual stresses were (-15.75, 12.84, 64.9, 37.74) MPa and the numerical results of residual stresses were (-15, 12, 59, and 37) MPa. The best value of residual stresses is (-15.75 and -15) MPa when it is in a compressive way. The results showed that the percentage error between numerical by using (ABAQUS/ CAE ver. 2017) and experimental work measured by X-ray diffraction is range (2-15) %.

Novel application of graphite-talc hybrid nanoparticle enriched cutting fluid in turning operation

2021 ◽  
Vol 62 ◽  
pp. 378-387
Author(s):  
Vaibhav Singh ◽  
Anuj Kumar Sharma ◽  
Ranjeet Kumar Sahu ◽  
Jitendra Kumar Katiyar
Keyword(s):  
Cutting Fluid ◽  
Turning Operation ◽  
Hybrid Nanoparticle

scholarly journals Analysis of Elastic Deflection of Single Point Cutting Tool and Optimization of Cutting Speed in Turning Operation by Using MADM Method

2021 ◽  
Vol 1104 (1) ◽  
pp. 012017
Author(s):  
Saurabh Dewangan ◽  
Somnath Chattopadhyaya ◽  
Amar Sharma ◽  
Varun Chaudhary ◽  
Ritwik Rohan
Keyword(s):  
Cutting Tool ◽  
Single Point ◽  
Cutting Speed ◽  
Turning Operation ◽  
Elastic Deflection

A Study of Turning Operation by Oil-Water Combined Mist Lubrication Machining Method

2001 ◽  
Vol 202-203 ◽  
pp. 47-52 ◽  
Author(s):  
D.C. Chen ◽  
Y. Suzuki ◽  
Kazufumi Sakai
Keyword(s):  
Turning Operation ◽  
Oil Water
Sign in / Sign up

Export Citation Format

Share Document