Effect of Yttria-Stabilized Zirconia (Y2O3/ZrO2) Nanoparticles Reinforced Cr3C2-25NiCr Coatings on the Microstructural and Mechanical Properties of Turbine Steel

2022 ◽  
Vol 11 (1) ◽  
pp. 20210080
Author(s):  
Rajinder Kumar ◽  
Deepak Bhandari ◽  
Khushdeep Goyal
Keyword(s):  
Mechanical Properties ◽  
Yttria Stabilized Zirconia ◽  
Zro2 Nanoparticles ◽  
Stabilized Zirconia ◽  
Turbine Steel

Microstructural examination of modified yttria stabilized zirconia by EM analytical techniques

1986 ◽  
Vol 44 ◽  
pp. 842-843
Author(s):  
W. W. Davison ◽  
R. C. Buchanan
Keyword(s):  
Mechanical Properties ◽  
Analytical Techniques ◽  
Yttria Stabilized Zirconia ◽  
Stabilized Zirconia ◽  
Transmission Microscopy ◽  
Sintering Aid ◽  
Densification Temperature ◽  
Chemical Inertness ◽  
Scanning Transmission ◽  
Microstructural Examination

Yttria stabilized zirconia (YSZ) has become a significant technological material due to its high ionic conductivity, chemical inertness, and good mechanical properties. Temperatures on the order of 1700°C are required, however, to densify YSZ to the degree necessary for good electrical and mechanical properties. A technique for lowering the densification temperature is the addition of small amounts of material which facilitate the formation of a liquid phase at comparatively low temperatures. In this study, sintered microstructures obtained from the use of Al2O3 as a sintering aid were examined with scanning, transmission, and scanning transmission microscopy (SEM, TEM, and STEM).

Effect of Coupled Conditions of Thermal Cycle and Dump Environment on Conductivity of 5mol% Yttria Stabilized Zirconia

2013 ◽  
Vol 591 ◽  
pp. 245-248 ◽  
Author(s):  
Jin Feng Xia ◽  
Hong Qiang Nian ◽  
Tao Feng ◽  
Hai Fang Xu ◽  
Dan Yu Jiang
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Transmission Electron Microscopy ◽  
High Temperature ◽  
Thermal Cycle ◽  
Oxygen Sensor ◽  
Yttria Stabilized Zirconia ◽  
Cyclic Change ◽  
Stabilized Zirconia ◽  
Transmission Electron

In some applications such as automotive oxygen sensor, 5mol% Y2O3stabilized zirconia (5YSZ) is generally used because it has both excellent ionic conductivity and mechanical properties. The automotive oxygen sensor would experience a cyclic change from high temperature (engine running) environment to the low temperature damp environment (in the tail pipe when vehicle stops). The conductivity change with coupled conditions of thermal cycle and dump environment in the 5mol%Y2O3ZrO2(5YSZ) system was examined by XRD,Impedance spectroscopy and transmission electron microscopy (SEM) in this paper.

scholarly journals Dense lanthanum silicate oxyapatite ceramics obtained by uniaxial pressing and slip casting

2018 ◽  
Vol 50 (4) ◽  
pp. 433-443
Author(s):  
Ramiro Toja ◽  
Nicolás Rendtorffa ◽  
Esteban Agliettia ◽  
Tetsuo Uchikoshi ◽  
Yoshio Sakka ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Vickers Hardness ◽  
Growth Process ◽  
Slip Casting ◽  
Yttria Stabilized Zirconia ◽  
Stabilized Zirconia ◽  
Oxygen Ion Conductivity ◽  
Oxygen Ion ◽  
Slip Cast ◽  
Lanthanum Silicate

Lanthanum silicate oxyapatite (LSO) is a promising ion conductive ceramic material, which has higher oxygen ion conductivity at intermediate temperatures (600-800?C) compared to yttria-stabilized zirconia. Its mechanical properties, though important for any of its applications, have been scarcely reported. In this study, we compare apparent densification, open porosity and Vickers hardness of samples conformed by uniaxial pressing and slip casting and fired up to 1600?C. Colloidal processing was optimized for slip casting in order to get high green densities. At sintering temperatures higher than 1400?C, both processing routes yielded comparable densities, although uniaxially pressed samples show slightly better mechanical properties, evidencing that slip cast ones already underwent a grain growth process.

Microstructure and Mechanical Properties of Multiscale Zirconia Ceramics Prepared by Field Assisted Sintering Technique

2016 ◽  
Vol 697 ◽  
pp. 354-359
Author(s):  
Khalid Eltayeb ◽  
Dong Qin Jin ◽  
Young Hwan Han ◽  
Fei Chen ◽  
Qiang Shen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Yttria Stabilized Zirconia ◽  
Milling Machine ◽  
Stabilized Zirconia ◽  
Zirconia Ceramics ◽  
Dense Structure ◽  
Zirconia Composites ◽  
20 Nm ◽  
Field Assisted Sintering

Two kinds of powders of 3 mol. % yttria stabilized zirconia (3Y–TZP) with different particles sizes; one was 20 nm denoted by N whereas the other was 0.5 µm denoted by M, were mechanically mixed via ball milling machine using different amounts of N wt. % to obtain multiscale zirconia composite powder. Then the mixed powders were sintered by field assisted sintering technique (FAST). The effect of N content on the microstructure as well as on mechanical properties of zirconia is investigated. Results show that the microstructure of M completely surrounded by N emerged in zirconia composites, and tetragonal phase is presented in all the sintered samples. The obtained zirconia ceramics with 15 wt. % N own a highly dense structure (~ 99.9 % relative density) and high flexural strength of 813.59 MPa wherein a 15 % increase in flexural strength compared to zirconia ceramics without adding N, but the fracture toughness of the composites just lightly decreases. The improved flexural strength of the composites is caused by the multiscale effect.

Sign in / Sign up

Export Citation Format

Share Document