Influence of Experimental Variables on the Measurement of Stress Corrosion Cracking Properties of High-Strength Steels

2009 ◽  
pp. 410-410-13 ◽  
Author(s):  
RW Judy ◽  
WE King ◽  
JA Hauser ◽  
TW Crooker
Keyword(s):  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
High Strength Steels ◽  
High Strength ◽  
Corrosion Cracking

Stress Corrosion Cracking of High Strength Steels

1995 ◽  
Author(s):  
Eun U. Lee ◽  
Henry Sanders ◽  
Bhaskar Sarkar
Keyword(s):  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
High Strength Steels ◽  
High Strength ◽  
Corrosion Cracking

Stress Corrosion Cracking of High Strength Steels and Titanium Al in Chloride Solutions at Ambient Temperature

CORROSION ◽  
1967 ◽  
Vol 23 (5) ◽  
pp. 142-148 ◽  
Author(s):  
M. H. PETERSON ◽  
B. F. BROWN ◽  
R. L. NEWBEGIN ◽  
R. E. GROOVER
Keyword(s):  
Ambient Temperature ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
High Strength Steels ◽  
High Strength ◽  
Corrosion Cracking ◽  
Chloride Solutions

scholarly journals On the Atmospheric Stress Corrosion Cracking of Low-Alloy High Strength Steels and Stainless Steels

1968 ◽  
Vol 17 (179) ◽  
pp. 723-728
Author(s):  
Kazuo HORIKAWA ◽  
Shuichiro TAKIGUCHI ◽  
Yoshio ISHIZU ◽  
Motokazu KANAZASHI
Keyword(s):  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Stainless Steels ◽  
High Strength Steels ◽  
High Strength ◽  
Corrosion Cracking

Microstructural Contributions to Stress Corrosion Cracking in High Strength Steels

1982 ◽  
Vol 40 ◽  
pp. 462-463
Author(s):  
R. Padmanabhan ◽  
W. E. Wood
Keyword(s):  
Heat Treatment ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
High Strength Steels ◽  
High Strength ◽  
Heat Treatments ◽  
Corrosion Cracking ◽  
Treatment Conditions ◽  
300M Steel ◽  
Conventional Heat Treatment

The effects of microstructural variables upon stress corrosion cracking resistance of 300M steel in 3.5% NaCl solution have been studied. Table 1 lists KIscc values for three heat treatment conditions. The martensite substructure was predominantly twinned plates for conventional heat treatment and dislocated laths for both high temperature and step heat treatments. A typical twinned region observed in the conventional heat treatment is shown in Fig. 1. Such twinned regions were less frequent in the other heat treatments. Both cementite and epsilon carbide were seen in all cases, as illustrated in Figs. 2 and 3 for conventional heat treatment. Epsilon carbide was usually observed within large grain boundary nucleated laths (autotempered martensite), with definite habit planes and growth directions. The formation of such laths have been discussed previously. Retained austenite, mostly in the form of interlath films, was observed in all cases with increased amounts present in coarser grained structures (Fig. 4).

Sign in / Sign up

Export Citation Format

Share Document