scholarly journals Microstructure Evolution of the Carbon Steels During Surface Severe Plastic Deformation

2021 ◽  
Vol 22 (4) ◽  
pp. 562-618
Author(s):  
M. O. Vasylyev ◽  
B. M. Mordyuk ◽  
S. M. Voloshko ◽  
D. A. Lesyk
Keyword(s):  
Electron Microscopy ◽  
Plastic Deformation ◽  
Carbon Steel ◽  
Severe Plastic Deformation ◽  
Microstructure Evolution ◽  
High Carbon Steel ◽  
Carbon Steels ◽  
Surface Mechanical Attrition Treatment ◽  
Low Carbon ◽  
Near Surface

The review is devoted to the state-of-the-art views on the microstructure evolution in structural and tool carbon steels during the surface severe plastic deformation (SPD). The main focus is on the effects of the nanocrystallization in the near-surface area of the low-carbon steel (C 0.05–0.2%), medium-carbon steel (C 0.35–0.65%), and high-carbon steel (C 1.0–1.5%). It is reviewed the following advanced surface SPD methods for the metal surfaces in recent years: an ultrasonic impact peening (UIP), high-frequency impact peening (HFIP), air blast shot peening (ABSP), surface mechanical attrition treatment (SMAT), and laser shock peening (LSP). Microstructure evolution before and after SPD is studied by optical microscopy (OM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The effects of the SPD parameters on the nanocrystalline modification of such main phase components of the carbon steels as ferrite, pearlite, and cementite are analysed. The atomic mechanism of the nanocrystallization is presented. The strain-hardening effect induced by SPD is demonstrated by the data of the near-surface microhardness profiles.

Investigations on Microstructure Evolution and Deformation Behavior of Aged and Ultrafine Grained Al-Zn-Mg Alloy Subjected to Severe Plastic Deformation

2010 ◽  
Vol 667-669 ◽  
pp. 253-258
Author(s):  
Wei Ping Hu ◽  
Si Yuan Zhang ◽  
Xiao Yu He ◽  
Zhen Yang Liu ◽  
Rolf Berghammer ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Severe Plastic Deformation ◽  
Microstructure Evolution ◽  
Deformation Behavior ◽  
Deformation Mechanisms ◽  
Mg Alloy ◽  
Ultrafine Grained

An aged Al-5Zn-1.6Mg alloy with fine η' precipitates was grain refined to ~100 nm grain size by severe plastic deformation (SPD). Microstructure evolution during SPD and mechanical behaviour after SPD of the alloy were characterized by electron microscopy and tensile, compression as well as nanoindentation tests. The influence of η' precipitates on microstructure and mechanical properties of ultrafine grained Al-Zn-Mg alloy is discussed with respect to their effect on dislocation configurations and deformation mechanisms during processing of the alloy.

Deformation and Structure Difference of Steel Droplets during Initial Solidification

2017 ◽  
Vol 36 (4) ◽  
pp. 347-357 ◽  
Author(s):  
Yang Li ◽  
Jing Wang ◽  
Jiaquan Zhang ◽  
Changgui Cheng ◽  
Zhi Zeng
Keyword(s):  
Carbon Steel ◽  
Continuous Casting ◽  
High Carbon Steel ◽  
Low Carbon Steel ◽  
Carbon Steels ◽  
Solidification Structure ◽  
Low Carbon ◽  
High Carbon ◽  
Peritectic Steel ◽  
Initial Solidification

AbstractThe surface quality of slabs is closely related with the initial solidification at very first seconds of molten steel near meniscus in mold during continuous casting. The solidification, structure, and free deformation for given steels have been investigated in droplet experiments by aid of Laser Scanning Confocal Microscope. It is observed that the appearances of solidified shells for high carbon steels and some hyper-peritectic steels with high carbon content show lamellar, while that for other steels show spherical. Convex is formed along the chilling direction for most steels, besides some occasions that concave is formed for high carbon steel at times. The deformation degree decreases gradually in order of hypo-peritectic steel, ultra-low carbon steel, hyper-peritectic steel, low carbon steel, and high carbon steel, which is consistent with the solidification shrinkage in macroscope during continuous casting. Additionally, the microstructure of solidified shell of hypo-peritectic steel is bainite, while that of hyper-peritectic steel is martensite.

Texture Evolution in Si-Alloyed Ultra Low-Carbon Steels after Severe Plastic Deformation

2010 ◽  
Vol 12 (10) ◽  
pp. 1077-1081 ◽  
Author(s):  
P. Gobernado ◽  
R. Petrov ◽  
D. Ruiz ◽  
E. Leunis ◽  
Leo A. I. Kestens
Keyword(s):  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Texture Evolution ◽  
Carbon Steels ◽  
Low Carbon ◽  
Low Carbon Steels

Crucible Steel in South India-Preliminary Investigations on Crucibles from Some Newly Identified Sites

1996 ◽  
Vol 462 ◽  
Author(s):  
Sharada Srinivasan
Keyword(s):  
Carbon Steel ◽  
Tamil Nadu ◽  
High Carbon Steel ◽  
Carbon Steels ◽  
Low Carbon ◽  
High Carbon ◽  
Metal Mining ◽  
Hypereutectoid Steel ◽  
Iron And Steel ◽  
Crucible Steel

ABSTRACTEuropean accounts from the 17th century onwards have referred to the repute and manufacture of “wootz’, a traditional crucible steel made especially in parts of southern India in the former provinces of Golconda, Mysore and Salem. Pliny's Natural History mentions the import of iron and steel from the Seres which have been thought to refer to the ancient southern Indian kingdom of the Cheras. As yet the scale of excavations and surface surveys is too limited to link the literary accounts to archaeometallurgical evidence, although pioneering exploratory investigations have been made by scholars, especially on the pre-industrial production sites of Konasamudram and Gatihosahalli discussed in 18th-19th century European accounts. In 1991–2 during preliminary surveys of ancient base metal mining sites, Srinivasan came across unreported dumps with crucible fragments at Mel-Siruvalur in Tamil Nadu, and Tintini and Machnur in Karnataka and she collected surface specimens from these sites as well as from the known site of Gatihosahalli. She was also given crucible fragments by the Tamil University, Tanjavur, from an excavated megalithic site at Kodumanal, dated to ca 2nd c. Bc, mentioned in Tamil Sangam literature (ca 3rd c. BC-3rd c. AD), and very near Karur, the ancient capital of the Sangam Cheras. Analyses of crucible fragments from the surface collection at Mel-Siruvalur showed several iron prills with a uniform pearlitic structure of high-carbon hypereutectoid steel (∼1–1.5% C) suggesting that the end product was uniformly a high-carbon steel of a structure consistent with those of high-carbon steels used successfully to experimentally replicate the watered steel patterns on ‘Damascus’ swords. Investigations indicate that the process was of carburisation of molten low carbon iron (m.p. 1400° C) in crucibles packed with carbonaceous matter. The fabric of crucibles from all the above mentioned sites appears similar. Preliminary investigations on these crucibles are thus reported to establish their relationship to crucible production of carbon steel and to thereby extend the known horizons of this technology further.

Effect of Post Annealing Treatment on Nano-Structured Low Carbon Steel Sheets Processed by Constrained Groove Pressing

2010 ◽  
Vol 667-669 ◽  
pp. 1009-1014 ◽  
Author(s):  
Farzad Khodabakhshi ◽  
Mohsen Kazeminezhad ◽  
Mohammad Azarnush ◽  
Seyyed Hossein Miran
Keyword(s):  
Plastic Deformation ◽  
Carbon Steel ◽  
Severe Plastic Deformation ◽  
Annealing Temperature ◽  
Low Carbon Steel ◽  
Annealing Process ◽  
Low Carbon ◽  
Temperature Range ◽  
Steel Sheets ◽  
Post Annealing

There are many works on annealing process of SPDed bulk metals but there are limited works on annealing process of SPDed sheets. Therefore, in this study the annealing response after constrained groove pressing (CGP) of low carbon steel sheets has been investigated. These sheets are subjected to severe plastic deformation at room temperature by CGP method up to three passes. Nano-structured low carbon steel sheets produced by severe plastic deformation are annealed at temperature range of 100 to 600 °C for 20 min. The microstructural changes after deformation and annealing are studied by optical microscopy. The effects of CGP strain and annealing temperature on microstructure, strength and hardness evolutions of the nano-scale grained low carbon steel are examined. The results show that annealing phenomena can effectively improve the elongation of process sheets with preserving the hardness and mechanical strength. Also, a thermal stability of microstructure can be observed with annealing at a temperature range of 375–425 °C and 400 °C is achieved as an optimum annealing temperature. Microstructure after post-annealing at temperatures of higher than 600 °C shows abnormal grain growth.

Surface Nanocrystallization of Low Carbon Steel Induced by Circulation Rolling Plastic Deformation

2005 ◽  
Vol 475-479 ◽  
pp. 133-136 ◽  
Author(s):  
Xin Min Fan ◽  
Bosen Zhou ◽  
Lin Zhu ◽  
Heng Zhi Wang ◽  
Jie Wen Huang
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
Surface Layer ◽  
Carbon Steel ◽  
Severe Plastic Deformation ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Surface Nanocrystallization ◽  
Average Grain Size ◽  
The Matrix

In this paper, the circulation rolling plastic deformation(CRPD) surface nanocrystallization technology is proposed based on the idea that the severe plastic deformation can induce grain refinement. The equipment of CRPD is designed and manufactured. A nanocrystallization surface layer was successfully obtained in a column sample of low carbon steel. The average grain size in the top surface layer is about 18 nm, and gradually increases with the distance from the surface. The hardness increases gradually from about 200HV0.1 in the matrix to about 600HV0.1 in the surface layer.

scholarly journals Strain Hardening of Low-Carbon Steel in the Area of Jerky Flow

2021 ◽  
pp. 65-75
Author(s):  
І. О Vakulenko ◽  
D. M Bolotova ◽  
S. V Proidak ◽  
B Kurt ◽  
A. E Erdogdu ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
Carbon Steel ◽  
Strain Hardening ◽  
Low Carbon Steel ◽  
Carbon Steels ◽  
Cold Plastic Deformation ◽  
Low Carbon ◽  
Jerky Flow ◽  
Ferrite Grain Size

Purpose. The aim of this work is to assess the effect of ferrite grain size of low-carbon steel on the development of strain hardening processes in the area of nucleation and propagation of deformation bands. Methodology. Low-carbon steels with a carbon content of 0.06–0.1% C in various structural states were used as the material for study. The sample for the study was a wire with a diameter of 1mm. The structural studies of the metal were carried out using an Epiquant light microscope. Ferrite grain size was determined using quantitative metallographic techniques. Different ferrite grain size was obtained as a result of combination of thermal and termo mechanical treatment. Vary by heating temperature and the cooling rate, using cold plastic deformation and subsequent annealing, made it possible to change the ferrite grain size at the level of two orders of magnitude. Deformation curves were obtained during stretching the samples on the Instron testing machine. Findings. Based on the analysis of stretching curves of low-carbon steels with different ferrite grain sizes, it has been established that the initiation and propagation of plastic deformation in the jerky flow area is accompanied by the development of strain hardening processes. The study of the nature of increase at dislocation density depending on ferrite grain size of low-carbon steel, starting from the moment of initiation of plastic deformation, confirmed the existence of relationship between the development of strain hardening at the area of jerky flow and the area of parabolic hardening curve. Originality. One of the reasons for decrease in Luders deformation with an increase of ferrite grain size of low-carbon steel is an increase in strain hardening indicator, which accelerates decomposition of uniform dislocations distribution in the front of deformation band. The flow stress during initiation of plastic deformation is determined by the additive contribution from the frictional stress of the crystal lattices, the state of ferrite grain boundaries, and the density of mobile dislocations. It was found that the size of dislocation cell increases in proportion to the diameter of ferrite grain, which facilitates the development of dislocation annihilation during plastic deformation. Practical value. Explanation of qualitative dependence of the influence of ferrite grain size of a low-carbon steel on the strain hardening degree and the magnitude of Luders deformation will make it possible to determine the optimal structural state of steels subjected to cold plastic deformation.

Sign in / Sign up

Export Citation Format

Share Document