High Temperature MOVPE Growth of AlxGa1−xN (0.2-1) Layers on Sapphire and SiC Substrates for the Fabrication Deep UV Optical Devices

2006 ◽  
Vol 955 ◽  
Author(s):  
Balakrishnan Krishnan ◽  
Masataka Imura ◽  
Kazuyoshi Iida ◽  
Kentaro Nagamatsu ◽  
Hiroki Sugimura ◽  
...  

ABSTRACTSingle crystalline AlN epitaxial layers have been grown on and (0001) sapphire and 6H-SiC substrates by MOVPE technique at high temperatures in the range of 1340-1500°C. The structural qualities of the high temperature grown AlN layers were found to be good as evidenced by X-ray diffraction analyses results. By transmission electron microscopic analysis, dislocation densities of the layers were found to be 6.2 × 107 cm−2 or lower and the formation of dislocation loops was confirmed. High temperature bridge layers of AlN and AlxGa1−xN layers were grown on linear-groove patterned sapphire based AlN templates and 6H-SiC substrates. AlxGa1−xN bridge layers exhibited different growth behaviours depending on the direction of groove patterns on the sub-strates.

2004 ◽  
Vol 19 (10) ◽  
pp. 2905-2912 ◽  
Author(s):  
Tokeer Ahmad ◽  
Ashok K. Ganguli

Nanoparticles of barium orthotitanate (Ba2TiO4) was obtained using microemulsions (avoiding Ba-alkoxide). Powder x-ray diffraction studies of the powder after calcining at 800 °C resulted in a mixture of orthorhombic (70%) and monoclinic (30%) phases. The high-temperature orthorhombic form present at 800 °C was due to the small size of particles obtained by the reverse micellar route. Pure orthorhombic Ba2TiO4 was obtained on further sintering at 1000 °C with lattice parameters a = 6.101(2) Å, b =22.94(1) Å, c = 10.533(2) Å (space group, P21nb). The particle size obtained from x-ray line broadening studies and transmission electron microscopic studies was found to be 40–50 nm for the powder obtained after heating at 800 °C. Sintering at 1000 °C showed increase in grain size up to 150 nm. Our studies corroborate well with the presence of a martensitic transition in Ba2TiO4. The dielectric constant was found to be 40 for Ba2TiO4 (at 100 kHz) for samples sintered at 1000 °C. The dielectric loss obtained was low (0.06) at 100 kHz.


1995 ◽  
Vol 52 (S1) ◽  
pp. 156-160 ◽  
Author(s):  
Lena N. Measures ◽  
Henry Hong

The number of moults in the egg of sealworm, Pseudoterranova decipiens (Nematoda: Ascaridoidea), and other ascaridoids is contentious. Transmission electron microscopic analysis of eggs and free-living larvae of sealworm confirmed that only one moult occurs in the egg. The first-stage larval (L1) cuticle on embryos was first observed in eggs incubated at 15 °C in sea water on day 5 after eggs were dissected from the uterus of sealworm obtained from the stomach of grey seals. There was no ecdysis of this L1 cuticle. A second cuticle began to form beneath the L1 cuticle between day 5 and 12. The second-stage larval (L2) cuticle continued to develop and on day 12 the L2 larva hatched enclosed within the cuticle of the first stage. The L1 cuticle appeared to be partially resorbed during development of the L2 cuticle. This study provides the first ultrastructural evidence of the number of moults that occur in eggs of sealworm.


Sign in / Sign up

Export Citation Format

Share Document