Correlation of Hydrogenated Nanocrystalline Silicon Microstructure and Solar Cell Performance

2004 ◽  
Vol 808 ◽  
Author(s):  
Keda Wang ◽  
Anthon Canning ◽  
J.R. Weinberg-Wolf ◽  
E.C.T. Harley ◽  
Daxing Han ◽  
...  

ABSTRACTWe used Raman and photoluminescence (PL) spectroscopy to study the relationship between the material properties and the solar cell performance of hydrogenated nanocrystalline silicon (nc-Si:H). The crystalline volume fraction (fc) was deduced from the Raman spectrum. Generally, a high fc leads to a high short circuit current density and a low open circuit voltage. PL spectra were measured using 632.8-nm and 442-nm laser lines. There are two distinguished PL peaks at 80 K, one at ∼1.4 eV originating from the amorphous region, while the other at = 0.9 eV from the nanocrystalline grain boundary regions. Generally, the intensity fraction of this low energy PL peak, IPLc/(IPLa+IPLc), was larger for 442-nm than 632.8-nm excitation, indicating an increase in crystallinity along the growth direction. However, for the best initial performance cells obtained by H2 dilution profiling and the i/p buffer layer, the intensity fraction IPLc/(IPLa+IPLc) decreased from the bulk to the topi/p interface. The Raman and PL results give insight into the correlation between the microstructures and the cell performance, and verified that properly-controlled crystallinity in the intrinsic layer and buffer layer at the i/p interface layer are important for optimizing nc-Si:H solar cells.

2018 ◽  
Vol 36 (3) ◽  
pp. 514-519
Author(s):  
Bechlaghem Sara ◽  
Zebentout Baya ◽  
Benamara Zineb

AbstractThe purpose of this work is to achieve the best efficiency of Cu(In, Ga)Se2 solar cells by replacing the CdS buffer layer with other nontoxic materials. The simulation tool used in this study is Silvaco-Atlas package based on digital resolution 2D transport equations governing the conduction mechanisms in semiconductor devices. The J-V characteristics are simulated under AM1.5G illumination. Firstly, we will report the modeling and simulation results of CdS/CIGS solar cell, in comparison with the previously reported experimental results [1]. Secondly, the photovoltaic parameters will be calculated with CdS buffer layer and without any buffer layer to understand its impact on the output parameters of solar cells. The simulation is carried out with the use of electrical and optical parameters chosen judiciously for different buffers (CdS, ZnOS and ZnSe). In comparison to simulated CdS/CIGS, the best photovoltaic parameters have been obtained with ZnOS buffer layer. The structure has almost the same open circuit voltage Voc and fill factor FF, and higher short circuit current density Jsc, which results in slightly higher conversion efficiencies.


2019 ◽  
Vol 14 (1) ◽  
pp. 75-84 ◽  
Author(s):  
Farjana Akter Jhuma ◽  
Mohammad Junaebur Rashid

AbstractThe performance of CZTS solar cell, a promising candidate in the field of energy production from sunlight, can be improved by optimizing the parameters of most widely used CdS buffer layer. In this work, numerical study have been done on the typical CZTS solar cell structures containing Mo thin film as back contact on glass substrate using SCAPS-1D solar cell simulation software. Then, the CZTS has been used as the absorber layer followed by CdS buffer later. Following, ZnO and transparent conducting oxide n-ITO layers have been considered as window layer and front contact, respectively. In the simulations, the CdS buffer layer has been doped with three different materials such as Silver (Ag), Copper (Cu) and Chlorine (Cl) for a wide acceptable range of carrier concentration. After obtaining the suitable carrier concentration, the thickness of the doped buffer layer has been varied keeping other layer parameters constant to see the variation of performance parameters open circuit voltage (Voc), short circuit current density (Jsc), fill factor (FF) and efficiency (η) of the CZTS solar cell.


2014 ◽  
Vol 1070-1072 ◽  
pp. 616-619
Author(s):  
Wen Bo Xiao ◽  
Jin Dai ◽  
Guo Hua Tu ◽  
Hua Ming Wu

The dye-sensitized solar cell performances influenced by radiant intensity and illuminated area in concentrating photovoltaic system are investigated experimentally and discussed theoretically. The results show that, under the same irradiated cells area, the short-circuit current is linearly increasing with the radiant intensity and the open-circuit voltage follows a logarithmic function of the radiant intensity. And, it is turned out that the short-circuit current and open-circuit voltage are obviously enhanced by increasing the illuminated cells surface area at the same radiant intensity. However, that growth trends will decline with an increase of the illuminated area. The reason is more defects involved in the process of increasing illumination area. All results can be interpreted using an equivalent circuit of a single diode model. A good agreement can be observed from the fitting curves. It is of great significance for current photovoltaic research.


2007 ◽  
Vol 1031 ◽  
Author(s):  
Christopher Bailey ◽  
Cory Cress ◽  
Ryne Raffaelle ◽  
Seth Hubbard ◽  
William Maurer ◽  
...  

AbstractThe effects of strain within stacked layers of InAs quantum dots (QDs) were investigated. InAs QD test structures with and without strain compensation (SC) were analyzed using atomic force microscopy, transmission electron microscopy, and X-ray diffraction. The affects of strain compensation on test structure morphology and on GaAs-based QD solar cell performance was studied as a function of the thickness of the SC layer. X-ray diffraction analysis of the QD embedded test structures reveals a relationship between the SC thickness and the observed crystalline quality. Air mass zero illuminated current vs. voltage data and spectral responsivity measurements were used for the solar cell comparison. When SC is employed, QD insertion shows a lower open circuit voltage, in reference to a baseline device without QDs, but leads to an enhancement in the short circuit current of the device.


2014 ◽  
Vol 925 ◽  
pp. 580-584 ◽  
Author(s):  
Mohamad Syafiq Alias ◽  
Sharul Ashikin Kamaruddin ◽  
Che Ani Norhidayah ◽  
Nurulnadia Sarip ◽  
Nayan Nafarizal ◽  
...  

In this paper, we explore the characteristics of bulk heterojunction solar cell based on poly (3-hexyl thiophene) [P3HT] and [6,6]-phenyl-C61-butyric acid methyl ester [PCBM] by introducing a buffer layer with device configuration of ITO/ZnO/P3HT:PCBM/Au. Nanostructured ZnO with individual diameter around 20-50 nm was used as the buffer layer and its effects on the short circuit current density, Jsc and open circuit voltage, Voc were investigated. It was found that, the electrical characteristic of the organic solar cell was obviously changed by introducing the buffer layer. Solar cell characteristic with Voc of 0.3939 V was obtained but the Jsc was very small. The surface topology of the P3HT:PCBM was investigated using an atomic force microscopy (AFM). ZnO nanoparticles were observed using a field emission scanning electron microscope (FESEM) and the electrical properties of the solar cell was measured using a solar simulator with a current – voltage (I-V) measurement system.


2021 ◽  
Vol 2114 (1) ◽  
pp. 012075
Author(s):  
Ammar J. Aswad ◽  
Nadeem K. Hassan ◽  
Adnan R. Ahmed

Abstract A general equation to determine properties of penternary solar cell based on Cu (In, Ga) (Se, S) 2 (CIGSSe) with a double buffer layer ZnS/Zn0.8Mg0.2O(ZMO) were derived. Numerical analysis of a (CIGSSe) solar cell with a double buffer layer ZnS/ZMO, CdS free absorber layer, were investigated using the AFORS-HET software simulation. Taking into consideration the effect of thickness and doping concentration for the CIGSSe absorption layer, ZnS buffer layer and ZnO:B(BZO) window layer on the electron transport, short circuit current density (Jsc) and open circuit voltage (Voc); numerical simulation demonstrated that the changes in band structure characteristics occurred. The solar energy conversion efficiency is 28.34%, the filling factor is 85.59%, the open circuit voltage is 782.3 mV, the short circuit current is 42.32 mA. then we take the range of the gradient between the ratio of x and y for the absorption layer, and the best result of Voc, Jsc, FF, Eff equal (838.7 mV, 40.94 mA/cm2, 86.23%, 29.61%) respectively at x= 0, y= 0.26.


Energies ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5986
Author(s):  
Tao Chen ◽  
Hao Guo ◽  
Leiming Yu ◽  
Tao Sun ◽  
Anran Chen ◽  
...  

Si/PEDOT: PSS solar cell is an optional photovoltaic device owing to its promising high photovoltaic conversion efficiency (PCE) and economic manufacture process. In this work, dopamine@graphene was firstly introduced between the silicon substrate and PEDOT:PSS film for Si/PEDOT: PSS solar cell. The dopamine@graphene was proved to be effective in improving the PCE, and the influence of mechanical properties of dopamine@graphene on solar cell performance was revealed. When dopamine@graphene was incorporated into the cell preparation, the antireflection ability of the cell was enhanced within the wavelength range of 300~450 and 650~1100 nm. The enhanced antireflection ability would benefit amount of the photon-generated carriers. The electrochemical impedance spectra test revealed that the introduction of dopamine@graphene could facilitate the separation of carriers and improve the junction quality. Thus, the short-circuit current density and fill factor were both promoted, which led to the improved PCE. Meanwhile, the influence of graphene concentration on device performances was also investigated. The photovoltaic conversion efficiency would be promoted from 11.06% to 13.15% when dopamine@graphene solution with concentration 1.5 mg/mL was applied. The achievements of this study showed that the dopamine@graphene composites could be an useful materials for high-performance Si/PEDOT:PSS solar cells.


Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.


Crystals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 726
Author(s):  
Ray-Hua Horng ◽  
Yu-Cheng Kao ◽  
Apoorva Sood ◽  
Po-Liang Liu ◽  
Wei-Cheng Wang ◽  
...  

In this study, a mechanical stacking technique has been used to bond together the GaInP/GaAs and poly-silicon (Si) solar wafers. A GaInP/GaAs/poly-Si triple-junction solar cell has mechanically stacked using a low-temperature bonding process which involves micro metal In balls on a metal line using a high-optical-transmission spin-coated glue material. Current–voltage measurements of the GaInP/GaAs/poly-Si triple-junction solar cells have carried out at room temperature both in the dark and under 1 sun with 100 mW/cm2 power density using a solar simulator. The GaInP/GaAs/poly-Si triple-junction solar cell has reached an efficiency of 24.5% with an open-circuit voltage of 2.68 V, a short-circuit current density of 12.39 mA/cm2, and a fill-factor of 73.8%. This study demonstrates a great potential for the low-temperature micro-metal-ball mechanical stacking technique to achieve high conversion efficiency for solar cells with three or more junctions.


2020 ◽  
Vol 92 (2) ◽  
pp. 20901
Author(s):  
Abdul Kuddus ◽  
Md. Ferdous Rahman ◽  
Jaker Hossain ◽  
Abu Bakar Md. Ismail

This article presents the role of Bi-layer anti-reflection coating (ARC) of TiO2/ZnO and back surface field (BSF) of V2O5 for improving the photovoltaic performance of Cadmium Sulfide (CdS) and Cadmium Telluride (CdTe) based heterojunction solar cells (HJSCs). The simulation was performed at different concentrations, thickness, defect densities of each active materials and working temperatures to optimize the most excellent structure and working conditions for achieving the highest cell performance using obtained optical and electrical parameters value from the experimental investigation on spin-coated CdS, CdTe, ZnO, TiO2 and V2O5 thin films deposited on the glass substrate. The simulation results reveal that the designed CdS/CdTe based heterojunction cell offers the highest efficiency, η of ∼25% with an enhanced open-circuit voltage, Voc of 0.811 V, short circuit current density, Jsc of 38.51 mA cm−2, fill factor, FF of 80% with bi-layer ARC and BSF. Moreover, it appears that the TiO2/ZnO bi-layer ARC, as well as ETL and V2O5 as BSF, could be highly promising materials of choice for CdS/CdTe based heterojunction solar cell.


Sign in / Sign up

Export Citation Format

Share Document