scholarly journals Electrical discharge machining with graphene flakes in dielectric

Mechanik ◽  
2017 ◽  
Vol 90 (3) ◽  
pp. 186-187 ◽  
Author(s):  
Rafał Świercz
Keyword(s):  
Surface Roughness ◽  
Experimental Investigation ◽  
Statistical Analysis ◽  
Process Parameters ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Graphene Flakes ◽  
Analysis Of Results ◽  
Edm Process

The article presents statistical analysis of results experimental investigation of EDM process with graphene flakes in dielectric. The relations between surface roughness and process parameters have been determined.

Investigation of the Spark Cycle Effect on Material Removal Rate in Wire Electrical Discharge Machining

Manufacturing ◽  
2003 ◽  
Author(s):  
Scott F. Miller ◽  
Albert J. Shih
Keyword(s):  
Process Parameters ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Short Circuit ◽  
Wire Electrical Discharge Machining ◽  
Time Duration ◽  
Edm Process

The development of new, advanced engineering materials and the needs for precise and flexible prototype and low-volume production have made wire electrical discharge machining (EDM) an important manufacturing process to meet such demand. This research investigates the effect of spark on-time duration and spark on-time ratio, two important EDM process parameters, on the material removal rate (MRR) and surface integrity of four types of advanced material: porous metal foams, metal bond diamond grinding wheels, sintered Nd-Fe-B magnets, and carbon-carbon bipolar plates. An experimental procedure was developed. During the wire EDM, five types of constraints on the MRR due to short circuit, wire breakage, machine slide speed limit, and spark on-time upper and lower limits have been identified. An envelope of feasible EDM process parameters is created and compared across different work-materials. Applications of such process envelope to select process parameters for maximum MRR and for machining of micro features are presented.

The Effect of the Electrical Discharge Machining Process on the Material Properties of Nonconductive Ceramics

2016 ◽  
Vol 4 (1) ◽  
Author(s):  
Nirdesh Ojha ◽  
Florian Zeller ◽  
Claas Mueller ◽  
Holger Reinecke
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Flexural Strength ◽  
Vickers Hardness ◽  
Electrical Discharge ◽  
High Performance ◽  
Electrical Discharge Machining ◽  
Machining Process ◽  
Hardness Increase ◽  
Edm Process

Electrical discharge machining (EDM) is widely used to manufacture complex shaped dies, molds and critical parts in conductive materials. With the help of an assisting electrode (AE), EDM process can be used to machine nonconductive ceramics. This paper evaluates the mechanical properties of three high-performance nonconductive ceramics (ZrO2, Si3N4, and SiC) that have been machined with the EDM process using AE. Mechanical properties such as Vickers hardness (HV 0.3), surface roughness (Sq), and flexural strength of the machined and the nonmachined samples are compared. The EDM process causes decrease in Vickers hardness, increase in surface roughness, and decrease in flexural strength.

Surface Roughness Optimization of Wire Electrical Discharge Machining Using ABC Algorithm

2015 ◽  
Vol 766-767 ◽  
pp. 902-907
Author(s):  
Bibin K. Tharian ◽  
B. Kuriachen ◽  
Josephkunju Paul ◽  
Paul V. Elson
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Wire Electrical Discharge Machining ◽  
Wire Tension ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time ◽  
Wire Feed

Wire electrical discharge machining is one of the important non-traditional machining processes for machining difficult to machine materials. It involves the removal of material by the discrete electric discharges produced between the inter electrode gap of continuously moving wire electrode and the work piece. The ability to produce intricate profiles on materials irrespective of the mechanical properties made this process to be widely used in industries. The present study investigates the relationship of various process parameters in WEDM of AISI 202 stainless steel with brass electrode.The experiments were planned according to Taguchi’s L18 orthogonal array and experimental models were developed. The important process parameters identified for the present study were pulse on time, peak current, pulse off time, wire feed, wire tension, dielectric flushing pressure, servo feed and gap voltage. The surface roughness of the machined surface was measured as the process performance measure. Analysis of variance test has also been carried out to check the adequacy of the developed models and to identify the level of significance of each process parameters. In addition to the developed models, ABC optimization has been performed to identify the optimum parameter combination for minimum surface roughness and the obtained optimal process parameters are peak current 11 A, pulse on time 100 μs, pulse off time 49 μs, wire feed 4 m/min, wire tension 10 N, flushing pressure 12 kg/cm2, servo feed 2100 mm/min and set gap voltage 30 V. Finally the results were verified with the experimental results and found that they are in good agreement.

Surface Study in a Non-conventional (Electrical Discharge Machining) Process for Grade 6 Titanium Material

2014 ◽  
Vol 68 (1) ◽  
Author(s):  
Md. Ashikur Rahman Khan ◽  
M. M. Rahman
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Machining Process ◽  
Machined Surface ◽  
Titanium Material ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

Electrical discharge machining (EDM) produces complex shapes and permits high-precision machining of any hard or difficult-to-cut materials. The performance characteristics such as surface roughness and microstructure of the machined face are influenced by numerous parameters. The selection of parameters becomes complicated. Thus, the surface roughness (Ra) and microstructure of the machined surface in EDM on Grade 6 titanium alloy are studied is this study. The experimental work is performed using copper as electrode material. The polarity of the electrode is maintained as negative. The process parameters taken into account in this study are peak current (Ip), pulse-on time (Ton), pulse-off time (Toff), and servo-voltage (Sv). A smooth surface finish is found at low pulse current, small on-time and high off-time. The servo-voltage affects the roughness diversely however, a finish surface is found at 80 V Sv. Craters, cracks and globules of debris are appeared in the microstructure of the machined part. The size and degree of craters as well as cracks increase with increasing in energy level. Low discharge energy yields an even surface. This approach helps in selecting proper process parameters resulting in economic EDM machining. 

An Investigation into Surface Roughness of EDM Using Soft Particles Suspension in Silicone Oil

2008 ◽  
Vol 389-390 ◽  
pp. 430-435 ◽  
Author(s):  
Yao Yang Tsai ◽  
Chih Kang Chang
Keyword(s):  
Surface Roughness ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Silicone Oil ◽  
Experimental Result ◽  
Dielectric Fluid ◽  
Polymer Particles ◽  
Hard Particles ◽  
Soft Particles ◽  
Edm Process

Electrical discharge machining (EDM) is an excellent technology to machining die and mold, but it is uneasy to obtain mirror-like surface. Powder-Mixed dielectric electrical discharge machining (PMD-EDM) is the innovative technology of EDM process, which can improve the quality of machined surface and applied in EDM finish machining now. The powder is usually hard particles, such as Al, Cu, Cr and Si in PMD-EDM. This paper presents a new research of PMD-EDM with suspending soft particles and abrasive grits in the dielectric fluid, especially focus on surface roughness. Experimental result shows the EDM process with polymer particles and abrasive grits can be carried out in silicone oil and the surface roughness has the finer improvement when increasing the rotation speed. Also, the effect of hard particles suspending in dielectric fluid are also discussed and compared. The surface roughness using polymer particles and abrasive in specific condition was better than only hard particles in silicone oil. Moreover, mixing abrasive and polymer in EDM can perform the polishing process.

Experimental investigations on surface integrity issues of Inconel-690 during wire-cut electrical discharge machining process

2016 ◽  
Vol 232 (4) ◽  
pp. 731-741 ◽  
Author(s):  
M Sreenivasa Rao ◽  
N Venkaiah
Keyword(s):  
Surface Roughness ◽  
Layer Thickness ◽  
Process Parameters ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Recast Layer ◽  
Machining Process ◽  
Micro Hardness ◽  
Recast Layer Thickness ◽  
Inconel 690

Nickel-based alloys are finding a wide range of applications due to their superior properties of maintaining hardness at elevated temperatures, low thermal conductivity and resistance to corrosion. These materials are used in aircraft, power-generation turbines, rocket engines, automobiles, nuclear power and chemical processing plants. Machining of such alloys is difficult using conventional processes. Wire-cut electrical discharge machining is one of the advanced machining processes, which can cut any electrically conductive material irrespective of its hardness. One of the major disadvantages of this process is formation of recast layer as it affects the properties of the machined surfaces. In this study, experimental investigation has been carried out to study the effect of wire-cut electrical discharge machining process parameters on micro-hardness, surface roughness and recast layer while machining Inconel-690 material. Interestingly, hardness of the machined surface was found to be lower than that of the bulk material. The micro-hardness and recast layer thickness are inversely related to the variation of process parameters. Recast layer thickness, surface roughness and hardness of the wire-cut electrical discharge machined surfaces of Inconel-690 are found to be in the range of 10–50 µm, 0.276–3.253 µm and 122–171 HV, respectively, for different conditions. The research findings and the data generated for the first time on hardness and recast layer thickness for Inconel-690 will be useful to the industry.

scholarly journals Analysis and Optimization of the Machining Characteristics of High-Volume Content SiCp/Al Composite in Wire Electrical Discharge Machining

Crystals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1342
Author(s):  
Hongzhi Yan ◽  
Bakadiasa Djo Kabongo ◽  
Hongbing Zhou ◽  
Cheng Wu ◽  
Zhi Chen
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
High Volume ◽  
Wire Electrical Discharge Machining ◽  
Al Composite

With the properties of high specific strength, small thermal expansion and good abrasive resistance, the particle-reinforced aluminum matrix composite is widely used in the fields of aerospace, automobile and electronic communications, etc. However, the cutting performance of the particle-reinforced aluminum matrix composite is very poor due to severe tool wear and low machining efficiency. Wire electrical discharge machining has been proven to be a good machining method for conductive material with any hardness. Even so, the high-volume SiCp/Al content composite is still a difficult-to-machine material in wire electrical discharge machining due to the influence of insulative the SiC particle. The goal of this paper is to analyze the machining characteristics and find the optimal process parameters for the high-volume content (65 vol.%) SiCp/Al composite in wire electrical discharge machining. Experimental results show that the material removal method of the SiCp/Al composite includes sublimating, decomposing and particle shedding. The material removal rate is found to increase with the increasing pulse-on time, first increasing and then decreasing with the increasing pulse-off time, servo voltage, wire feed and wire tension. Pulse-on time and servo voltage are the dominant factors for surface roughness. In addition, the multi-objective optimization method of the nondominated neighbor immune algorithm is presented to optimize the process parameters for a fast material removal rate and low surface roughness. The optimized process parameters can increase the material removal rate by 34% and reduce the surface roughness by 6%. Furthermore, the effectiveness of the Pareto optimal solution is proven by the verified experiment.

Sign in / Sign up

Export Citation Format

Share Document