Assessment of Liquid Metals as Heat Transfer Fluid for Solar Parabolic Trough Collector Applications

2017 ◽  
Author(s):  
N. V. V Krishna Chaitanya ◽  
Ravi Kumar K
Keyword(s):  
Heat Transfer ◽  
Liquid Metals ◽  
Heat Transfer Fluid ◽  
Parabolic Trough ◽  
Parabolic Trough Collector

scholarly journals Contribution to the Parametric Study of the Performance of A Parabolic Trough Collector

2021 ◽  
Vol 321 ◽  
pp. 02016
Author(s):  
Belkacem Bouali ◽  
Hanane-Maria Regue
Keyword(s):  
Heat Transfer ◽  
Mass Flow ◽  
Flow Rate ◽  
Optimal Operation ◽  
Heat Transfer Fluid ◽  
Parabolic Trough ◽  
Parabolic Trough Collector ◽  
Heat Transfer Fluids ◽  
Ansys Cfx ◽  
Different Seasons

This paper presents an analysis of the performance of a parabolic trough collector (PTC) according to some key operating parameters. The effects of the secondary reflector, the length and thickness of the absorber tube (receiver tube) and the flow rate of the heat transfer fluid (HTF) are investigated. The main objective is to determine an optimal operation, which improves the performance of a traditional PTC. The target variables are the temperature at the outlet of the tube, the amount of energy collected by the HTF and the efficiency of the system. The solar flux data concern the city of LAGHOUAT located in the south of Algeria. Four days in different seasons are considered. The optical analysis of the system is performed by using the open source SolTrace code. The output of this analysis is used as a boundary condition for the CFD solver. The conjugate heat transfer and the fluid flow through the absorber tube are simulated by using ANSYS-CFX solver. Water is considered as heat transfer fluids. The obtained results show that the use of a curved secondary reflector significantly improves the performance of the traditional PTC. As the thickness of the tube increases, the heat storage in the material increases, which increases the temperature at the exit of the tube and therefore the efficiency of the system. However, the length of the tube depends on the mass flow of the HTF and vice versa. To keep the efficiency constant by choosing another length, it is necessary to choose a mass flow rate proportional to the flow rate corresponding to the initial length.

Comparative Study on Parabolic Trough Collector by using Different Heat Transfer Fluids

2019 ◽  
Vol 11 (4) ◽  
Author(s):  
Krishna Mounica ◽  
Y.V. Hanumantha Rao ◽  
Vinay Atgur ◽  
G. Manavendra ◽  
B. Srinivasa Rao
Keyword(s):  
Heat Transfer ◽  
Mass Flow ◽  
Thermal Model ◽  
Heat Transfer Fluid ◽  
Parabolic Trough ◽  
Flow Rates ◽  
Parabolic Trough Collector ◽  
Heat Transfer Fluids ◽  
Mass Flow Rates ◽  
Simulation Results

In this paper the use of Syltherm-800 and Therminol-55 thermal oils in parabolic trough collector (PTC) is investigated with inlet temperatures of 375.35 K, 424.15 K, 470.65 K and 523.85 K and for mass flow rates of 4, 4.5 and 5 kg/sec. Analysis has been carried out using a thermal model and validated using the simulation results. Therminol-55 gives better heat transfer coefficient compared to Syltherm-800. Since Therminol-55 has higher specific heat and viscosity when compared to Syltherm-800, the use of Syltherm-800 as a heat transfer fluid in PTC is preferred. Better results are observed for temperature of 375.35 K and mass flow rate of 4 kg/sec.

scholarly journals Feasibility Study of Freeze Recovery Options in Parabolic Trough Collector Plants Working with Molten Salt as Heat Transfer Fluid

Energies ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 2340 ◽  
Author(s):  
Cristina Prieto ◽  
Alfonso Rodríguez-Sánchez ◽  
F. Ruiz-Cabañas ◽  
Luisa Cabeza
Keyword(s):  
Heat Transfer ◽  
Molten Salt ◽  
Molten Salts ◽  
Heat Transfer Fluid ◽  
Operational Experience ◽  
Parabolic Trough ◽  
Solar Salt ◽  
Parabolic Trough Collector ◽  
Overall Performance ◽  
Solar Field

Parabolic trough collector (PTC) technology is currently the most mature solar technology, which has led to the accumulation of relevant operational experience. The overall performance and efficiency of these plants depends on several components, and the heat transfer fluid (HTF) is one of the most important ones. Using molten salts as HTFs has the advantage of being able to work at higher temperatures, but it also has the disadvantage of the potential freezing of the HTF in pipes and components. This paper models and evaluates two methods of freeze recovery, which is needed for this HTF system design: Heat tracing in pipes and components, and impedance melting in the solar field. The model is used to compare the parasitic consumption in three molten salts mixtures, namely Solar Salt, HiTec, and HiTec XL, and the feasibility of this system in a freezing event. After the investigation of each of these subsystems, it was concluded that freeze recovery for a molten salt plant is possible.

scholarly journals A Study on Performance Enhancement of Parabolic Trough Collector

2020 ◽  
Vol 170 ◽  
pp. 01030
Author(s):  
Aditya Bawane ◽  
Sanjay Lakade ◽  
Virendra Bhojwani
Keyword(s):  
Heat Transfer ◽  
Solar Energy ◽  
System Performance ◽  
Performance Enhancement ◽  
3D Analysis ◽  
Energy Extraction ◽  
Parabolic Trough ◽  
Parabolic Trough Collector ◽  
Glass Cover ◽  
Parabolic Collector

Solar energy is available in abundant quantity which can be utilized for thermal and power generation applications. The maximum solar energy extraction for application is challenging. This review focuses on the performance enhancement of parabolic trough collector. Heat transfer through absorber tube, various nanofluids with concentration is stated. Thermal efficiency increases due to the use of parabolic collector with booster reflector and glass cover over the system performance. The complex 3D analysis (ANSYS) gives accurate distribution of heat flux over the absorber tube.

Sign in / Sign up

Export Citation Format

Share Document