scholarly journals Strengthening of Reinforced Concrete Beams Subjected to Concentrated Loads

2022 ◽  
Author(s):  
Paolo Foraboschi
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Concrete Beams ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Reinforced Concrete Structure ◽  
Concentrated Loads ◽  
Concentrated Load ◽  
Load Carrying

Renovation, restoration, remodeling, refurbishment, and retrofitting of build-ings often imply modifying the behavior of the structural system. Modification sometimes includes applying forces (i.e., concentrated loads) to beams that before were subjected to distributed loads only. For a reinforced concrete structure, the new condition causes a beam to bear a concentrated load with the crack pattern that was produced by the distributed loads that acted in the past. If the concentrated load is applied at or near the beam’s midspan, the new shear demand reaches the maximum around the midspan. But around the midspan, the cracks are vertical or quasi-vertical, and no inclined bar is present. So, the actual shear capacity around the midspan not only is low, but also can be substantially lower than the new demand. In order to bring the beam capacity up to the demand, fiber-reinforced-polymer composites can be used. This paper presents a design method to increase the concentrated load-carrying capacity of reinforced concrete beams whose load distribution has to be changed from distributed to concentrated, and an analytical model to pre-dict the concentrated load-carrying capacity of a beam in the strengthened state.

Experimental Study on Shear Strengthening of Reinforced Concrete Beams Using Different Techniques of Concrete Jacketing

2021 ◽  
Vol 21 (2) ◽  
pp. 53-61
Author(s):  
Mohammed F. Ojaimi
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Failure Modes ◽  
Shear Failure ◽  
Concrete Beams ◽  
Shear Capacity ◽  
Fiber Reinforced Concrete ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Load Carrying

A large number of RC structures or at least some of their members need strengthening or rehabilitation. Among the typical failure modes, the shear failure is more dangerous and less predictable, because of usually brittle behavior and sudden collapse. Therefore, there are necessities for upgrading the shear capacity and the local ductility of reinforced concrete beams. In this study, four different techniques of concrete jacketing were used to improve the behaviors of the shear deficiencies beams. The four techniques used in this study to enhance the behavior of the beams were by using a Self-Compacted Fiber Reinforced Concrete jacket without stirrups (S.-J. + Steel Fiber), a concrete jacket of Self Compacted Concrete with stirrups (S.-J. + Stirrups), a concrete jacket of ferrocement jacket (S.-J. + Ferrocement), and a concrete jacket of ferrocement jacket with external steel reinforcing bars (S.-J. + Ferrocement + R). These techniques contributed to enhancing the load-carrying capacity and delaying the appearance of the first crack in tested beams compared with the control beam by a percentage of (35, 59, 30, 6) % and (18, 35, 81, 80) %, respectively. The specimen (S.-J. + Stirrups) showed the best performance in comparison with the other used strengthening techniques used in this study in terms of stiffness and the ultimate load-carrying capacity. The ferrocement jacket (S.-J. + Ferrocement) was found to be the most suitable jacketing system used to enhance the shear capacity in terms of cracking load.

Guidelines for flexural design of FRP reinforced concrete beams

2020 ◽  
pp. 002199832097373
Author(s):  
Fares Jnaid
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Concrete Beams ◽  
Large Diameter ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Concrete Compressive Strength ◽  
Load Carrying ◽  
Multiple Variables

This paper investigates the effects of different parameters on the live load carrying capacity of concrete beams reinforced with FRP bars. The author performed a parametric study utilizing an innovative numerical approach to inspect the effects of multiple variables such as reinforcement ratio, concrete compressive strength, span to depth ratio, FRP type, and bar diameter on load carrying capacity of FRP reinforced concrete beams. This study concluded that unless the span to height ratio is smaller than 8, tension-controlled sections are impractical as they do not meet code requirements for serviceability. In addition, it is recommended to use higher reinforcement ratios when using larger span to depth ratios and/or when using CFRP reinforcing bars. Moreover, larger number of bars with small diameter is more practical than fewer large diameter bars. Furthermore, this research suggests that increasing the concrete compressive strength is associated with a significant increase in the ultimate flexural capacity of FRP reinforced beams.

scholarly journals The influence of simultaneous action of the aggressive environment and loading on strength of RC beams

2018 ◽  
Vol 183 ◽  
pp. 02002 ◽  
Author(s):  
Jacek Selejdak ◽  
Roman Khmil ◽  
Zinoviy Blikharskyy
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Simultaneous Action ◽  
Load Carrying Capacity ◽  
Aggressive Environment ◽  
Load Carrying ◽  
Acid Environment ◽  
Simultaneous Influence

The article is devoted to an experimental research of the strength of reinforced concrete beams, and its dependence on a simultaneous influence of a corrosion environment and a loading factor. The tests have been carried out upon reinforced concrete specimens of 2100×200×100 mm size, with a regular reinforcement. The beams are of a span equaling to 1,9m with different reinforcing ratio of beams. The acid environment, namely 10 % H2SO4, was taken as a model of an aggressive environment. Reinforced concrete beams have been tested with and without the co-action of the aggressive environment and loading factor. Beams, which underwent a simultaneous action of the corrosive environment and loading, were loaded to a level 0.7 of its load-carrying capacity. The load-carrying capacity in aggressive environment in all the beams of all the series was achieved in 46-60 days. The influence of the simultaneous action of the aggressive environment and loading on the strength of reinforced-concrete beams has been described in the following work. It is necessary to note that the design code of Ukraine does not allow determining load carrying capacity of the beams affected by corrosion with simultaneous influence of loading with adequate accuracy. The analysis of experimental data has been done and the main directions of the design code’s correction have been formulated.

Responses of Plain and Steel Fiber-Reinforced Concrete Beams to Temperature and Mechanical Loads: Experimental Study

2000 ◽  
Vol 1740 (1) ◽  
pp. 25-32 ◽  
Author(s):  
Ali Alavizadeh-Farhang ◽  
Johan Silfwerbrand
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Steel Fiber ◽  
Concrete Beams ◽  
Fiber Reinforced Concrete ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Load Carrying

To study the structural responses of plain and steel fiber-reinforced concrete pavements under combined mechanical and thermal loads, two test series have been conducted with plain and steel fiber-reinforced concrete beams. The magnitude and duration of the differences in the induced stresses caused by traffic load and a positive nonlinear temperature gradient (the top surface was warmer than the bottom surface during the day) may lead to some relaxation of thermal stresses and subsequently increase the load-carrying capacity. Considering the loss of support contact in the interior part of the concrete pavement, the experimental study of combined loading with restrained concrete beams may provide some insight and an indication of whether the superposition of stresses is a proper approach. The beams were subjected to solely thermal, solely mechanical, and combined thermal and mechanical loads while the rotation of the beam at supports was prevented. The results of tests conducted with both plain and steel fiber-reinforced beams showed that the superposition of stresses under combined loading before cracking gave a satisfactory estimation of the load-carrying capacities. The results also showed that the effect of relaxation of stresses due to short-term thermal loads was not noticeable in the load-carrying capacity achieved in tests with combined thermal and mechanical loads. On the contrary, a tendency for reduction of the load-carrying capacity was observed at higher thermal gradients. In addition, the overall structural responses of steel fiber-reinforced concrete beams under mechanical load and a nonlinear temperature gradient combined were similar to the responses of plain concrete beams up to the cracking stage. However, the release of thermal stresses due to cracking and the considerable residual load-carrying capacity after cracking were the most important observations for steel fiber-reinforced concrete beams.

scholarly journals Flexural Behaviour Of Reinforced Concrete Beams Containing Expanded Glass As Lightweight Aggregates

2015 ◽  
Vol 23 (4) ◽  
pp. 1-7 ◽  
Author(s):  
Jamal Khatib ◽  
Adrian Jefimiuk ◽  
Sammy Khatib
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Fine Aggregate ◽  
Load Carrying Capacity ◽  
Flexural Behaviour ◽  
Structural Concrete ◽  
Load Carrying

Abstract The flexural properties of reinforced concrete beams containing expanded glass as a partial fine aggregate (sand) replacement are investigated. Four concrete mixes were employed to conduct this study. The fine aggregate was replaced with 0%, 25%, 50% and 100% (by volume) expanded glass. The results suggest that the incorporation of 50% expanded glass increased the workability of the concrete. The compressive strength was decreasing linearly with the increasing amount of expanded glass. The ductility of the concrete beam significantly improved with the incorporation of the expanded glass. However, the load-carrying capacity of the beam and load at which the first crack occurs was reduced. It was concluded that the inclusion of expanded glass in structural concrete applications is feasible.

scholarly journals Degradation of the EBR-CFRP strengthening system applied to reinforced concrete beams exposed to weathering

2021 ◽  
Vol 14 (2) ◽  
Author(s):  
Gláucia Maria Dalfré ◽  
Guilherme Aris Parsekian ◽  
Douglas da Costa Ferreira
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Concrete Beams ◽  
Natural Aging ◽  
Outdoor Exposure ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Externally Bonded ◽  
Cfrp Composite

Abstract Little is known about the behavior and durability of strengthening systems applied on concrete substrata and the possible loss of performance due to the degradation of the intervening materials by the structure’s natural aging process and exposure of the externally strengthened elements to aggressive environments. In this context, the present work presents an experimental analysis of the behavior of reinforced concrete beams strengthened with Carbon Fiber Reinforced Polymer (CFRP), applied according to the Externally Bonded Reinforcement (EBR) technique, maintained in a laboratory environment (indoor and protected) or exposed to weathering (outdoor exposure). In addition, specimens of the intervenient materials were also molded and exposed to the same environmental conditions as the beams. The results indicate that weather-exposed epoxy adhesives present reductions up to 70% in their mechanical properties after exposure, while the CFRP composite properties remain similar. It was also found that the strengthening system provided 50% and 28% increments in the load-carrying capacity and stiffness of the elements, respectively. However, the tests conducted after 6 months of weathering exposure showed a 10% reduction in the load-carrying capacity of the strengthened elements.

scholarly journals The analysis of load carrying capacity and cracking of slightly reinforced concrete members in bending

2008 ◽  
Vol 2 (1) ◽  
pp. 065-078
Author(s):  
Marta Słowik
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Concrete Beams ◽  
Plain Concrete ◽  
Reinforcement Ratio ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Test Results ◽  
Concrete Members ◽  
Load Carrying

Slightly reinforced concrete members are the members made by concrete with reinforcement less than minimum given in codes for reinforced concrete ones. Plain concrete and slightly reinforced concrete members in bending are treated in the same way during the dimensioning and the influence of longitudinal reinforcement on the load carrying capacity is not taken into account. The mechanism of work and crack formation in slightly reinforced concrete members is not completely recognized. The author’s own research program was made. The experiment was aimed at the determination of cracking moment and load carrying capacity of slightly reinforced concrete beams with different reinforcement ratio. Also plain concrete beams and the typical reinforced concrete beam were tested. The analysis of the obtained values of maximum bending moment and crack’s widths was made according to the reinforcement ratio. The analysis of test results shows how the presence of longitudinal steel bars in concrete members, even when reinforcement ratio is low, changes cracking process and influences the value of cracking moment in flexural members. On the basis of test results, the method how to calculate the load carrying capacity of slightly reinforced concrete elements in bending has been proposed.

Experimental Study on Flexural Strength of Reinforced Concrete Beam Exposed to Acid Deposition in the Laboratory

2011 ◽  
Vol 94-96 ◽  
pp. 1494-1499
Author(s):  
Ying Fang Fan ◽  
Da Wei Wang ◽  
Shi Yi Zhang
Keyword(s):  
Reinforced Concrete ◽  
Acid Rain ◽  
Carrying Capacity ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Flexural Behavior ◽  
Load Carrying Capacity ◽  
The Real ◽  
Artificial Rainfall ◽  
Load Carrying

In this study, the flexural behavior of the reinforced concrete beams attacked by acid rain environment is investigated. The objective is to discover the deterioration mechanism of the concrete beams servicing in the acid rain environment. An artificial rainfall device was designed. Eleven reinforced concrete beams, 120mm×200mm in cross-section were prepared in the laboratory. Three accelerating corrosion methods, which inclusive of immersion method, dry-wet cycle method, and artificial rainfall method, were applied to simulate the action of the real acid rain respectively. The acid solutions with pH level 1.5 and 2.5 were prepared by the mixture of sulfate and nitric acid solution respectively. One of the beams was tested in the natural condition to serve as reference; the remaining ten beams were tested after being exposed to the simulated acid environments for certain periods. Ultrasonic technology was applied to evaluate the damage depth and the compressive strength of the concrete. Dynamic test was applied to estimate the integrity of the beam. Three-point bending tests were performed to investigate the load carrying capacity of the beams. Mechanical properties of concrete and load carrying capacity of the beams exposed to different accelerated corrosion methods are obtained and compared. It is illustrated that the designed artificial device is efficient to simulate the real acid rainfall. It is shown that the strength of concrete, frequency and ultimate load of the beams, have a direct relationship to the damage degree of the beams.

Sign in / Sign up

Export Citation Format

Share Document