A Control System for a Tool Use Robot: Drawing a Circle by Educing Functions of a Compass

2017 ◽  
Vol 29 (2) ◽  
pp. 395-405
Author(s):  
Kyo Kutsuzawa ◽  
◽  
Sho Sakaino ◽  
Toshiaki Tsuji
Keyword(s):  
Control System ◽  
Coordinate System ◽  
Tool Use ◽  
Controller Design ◽  
Multiple Points ◽  
Mechanical Constraints ◽  
Robotic Tool ◽  
Selection Of

[abstFig src='/00290002/12.jpg' width='260' text='Axes in the compass coordinate system' ] Robotic tool use is one of various approaches for actualizing versatility of robots, and is thus the focus of many studies. However, selection of the controllers for tool use and how to design them remains indeterminate. This paper addresses the task of drawing a circle with a compass as an example of tool use. This task mandates to deal with complex contact at multiple points and needs to educe functions of the compass to draw a circle accurately. This paper demonstrates the implementation and corresponding method of compass controller design. The method of designing the controller for the compass entails decomposing the usage of the compass into semantic units and subsequently defining a coordinate system and fabricating the controller via mapping of the semantic units to axes. The implementation of a controller for compass use indicates that the ability of the compass to accurately draw a circle is educed via mechanical constraints of the compass. We validated the implemented controller by drawing a circle and comparing the result to a circle drawn using a pencil.

DESIGN, SIMULATION AND IMPLEMENTATION MONITORING SYSTEM FOR SYSTEM CONTROL C4 FEEDING PUMP FOR FEED VAPORIZATION IN THE BUTADIENE PLANT

2020 ◽  
Vol 1 (1) ◽  
pp. 31-35
Author(s):  
Fahmi Yunistyawan ◽  
Yunistyawan J Berchmans ◽  
Gembong Baskoro
Keyword(s):  
Motor Control ◽  
Control System ◽  
Field Operator ◽  
System Control ◽  
Variable Speed ◽  
Variable Speed Drive ◽  
Software And Hardware ◽  
Discharge Pressure ◽  
Selection Of

This study implements the auto start control system on an electric motor 3 phase C4Feeding pump when the discharge pressure is low-low (4.3 kg /cm²). The C4 feeding pumpmotor was initially manually operated from the local control station, this was very ineffectiveand inefficient because it still relied on the field operator to operate the pump motor and whenthe plant was in normal operating it is very risk if the field operator late to operate motor then itwill impact to quality of the product, and if the delay time to operate motor is too long then planthave to shut down, therefore improvement is needed in the C4 feeding pump motor controlsystem. In this paper, various types of 3-phase motor control are explained which allow it to beapplied to the C4 feeding pump motor that are on-off, inverter, and variable speed drive andefficient selection of the three systems control of the motor. Software and hardware used in thisthesis work are DCS CENTUM VP Yokogawa.

Path Tracking Controller Design of Automatic Guided Vehicle Based on Four-Wheeled Omnidirectional Motion Model

2020 ◽  
Vol 17 (2) ◽  
pp. 7996-8010
Author(s):  
X. Wu ◽  
Y. Yang
Keyword(s):  
Control System ◽  
Fuzzy Controller ◽  
Controller Design ◽  
Threshold Value ◽  
Position Angle ◽  
Path Tracking ◽  
Global Coordinate System ◽  
Automatic Guided Vehicle ◽  
Input Variables ◽  
Industrial Pc

This paper presents a new design of omnidirectional automatic guided vehicle based on a hub motor, and proposes a joint controller for path tracking. The proposed controller includes two parts: a fuzzy controller and a multi-step predictive optimal controller. Firstly, based on various steering conditions, the kinematics model of the whole vehicle and the pose (position, angle) model in the global coordinate system are introduced. Secondly, based on the modeling, the joint controller is designed. Lateral deviation and course deviation are used as the input variables of the control system, and the threshold value is switched according to the value of the input variable to realise the correction of the large range of posture deviation. Finally, the joint controller is implemented by using the industrial PC and the self-developed control system based on the Freescale minimum system. Path tracking experiments were made under the straight and circular paths to test the ability of the joint controller for reducing the pose deviation. The experimental results show that the designed guided vehicle has excellent ability to path tracking, which meets the design goals.

scholarly journals Collective Losses of Low Power Cage Induction Motors—A New Approach

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1749
Author(s):  
Elzbieta Szychta ◽  
Leszek Szychta
Keyword(s):  
Control System ◽  
Experimental Studies ◽  
Complex Problem ◽  
Accurate Estimation ◽  
New Approach ◽  
Water Pumping ◽  
Efficiency Control ◽  
Interacting Systems ◽  
Cage Induction Motor ◽  
Selection Of

Energy efficiency of systems of water pumping is a complex problem since efficiency of two distinct interacting systems needs to be combined: water and power supply. This paper introduces a non-intrusive method of calculating the so-called “collective losses” of a cage induction motor. The term “collective losses”, which the authors define, allows for accurate estimation of motor efficiency. Control system of a pump determines operating point of a pumping station, and thus its efficiency. General estimated performance characteristics of a motor, components of a control system, are assumed to serve selection of a range of pumping speed variations. Rotational speed has a direct effect on motor load torque, pump power and head, and thus on motor performance. Hellwig’s statistical method was used to specify characteristics of estimated collective losses on the basis of experimental studies of 21 motors rated at up to 2.2 kW. The results of simulations and experiments are used to verify validity and efficiency of the suggested method. The method is non-intrusive, simple to use, and requires minimum data.

Sign in / Sign up

Export Citation Format

Share Document