Data Driven Virtual Flow Metering: Leveraging AI and Edge Computing for Continuous Multiphase Flow Measurement

2021 ◽  
Author(s):  
Helmut Schnabl ◽  
Helmut Wimmer ◽  
Michael Nirtl ◽  
Sasa Blazekovic

Abstract This paper describes the use of data-driven virtual flow metering (VFM) for continuous multiphase flow measurement, which has been developed and tested in an oil field well pilot in Austria. 12 ESP (Electric Submersible Pump) wells have been modelled and fine-tuned within the pilot. Hardware-based test separators were used to conduct quality control evaluations on the predicted production rates and calibrate the well models as required. For the practical deployment of VFM systems, we have addressed the need for optimized learning and scalability of the artificial intelligence (AI) models by means of what we call soft-sensing and will explain how to successfully deploy this technology on wells with artificial lift. Notably, the application of this software-based, soft-sensing VFM in combination with hardware-based multiphase flow measurement bears the potential to significantly reduce the CAPEX cost for future metering infrastructure investments and even reduce the OPEX of existing metering hardware by extending the duration of metering cycles. This makes data-driven VFM an economical option even for low-producing wells. Details of the well pilot project conducted with OMV in Austria will be provided. The use of soft-sensing VFMs via cloud computing for continuous multiphase flow measurement is a step toward the closed-loop, fully autonomous operation of oil fields.

2018 ◽  
Author(s):  
Fatma Bahar Hosgor ◽  
Haluk Toral ◽  
Shiqian Cai ◽  
Maksim Dudich ◽  
Arman Ilyassov ◽  
...  

2018 ◽  
Author(s):  
Fatma Bahar Hosgor ◽  
Haluk Toral ◽  
Shiqian Cai ◽  
Maksim Dudich ◽  
Arman Ilyassov ◽  
...  

2013 ◽  
Vol 64 (5) ◽  
Author(s):  
Muhammad Jaysuman Pusppanathan ◽  
Fazlul Rahman Yunus ◽  
Nor Muzakkir Nor Ayob ◽  
Ruzairi Abdul Rahim ◽  
Fatin Aliah Phang ◽  
...  

Electrical capacitance tomography (ECT) is one of process tomography technique which is developed rapidly in recent years. ECT is an imaging technique to obtain the internal permittivity distribution of a vessel or pipe by using capacitance electrodes sensor. This method has been integrated with ultrasonic tomography as multimodality system to perform multiphase flow measurement such as crude oil separation and oil process industry. In the present paper, a novel type of ECT sensor was developed using copper FR4 material. The electrode sensors can be flexibly bend or curve to fit the pipe surface for optimum measurement. Thus, every single sensor strip is designed to be functioned independently. Such system has lower sensing capability in the central of the sensing area which often contributes to poor imaging result. This problem can be overcome by combining the ECT with ultrasonic tomography to form a dual modality tomography system. By implementing the new ECT sensor, multiphase flow measurement image results can be achieved. The reconstructed image results are presented in this paper.


2021 ◽  
Author(s):  
Mohammed Ahmed Al-Janabi ◽  
Omar F. Al-Fatlawi ◽  
Dhifaf J. Sadiq ◽  
Haider Abdulmuhsin Mahmood ◽  
Mustafa Alaulddin Al-Juboori

Abstract Artificial lift techniques are a highly effective solution to aid the deterioration of the production especially for mature oil fields, gas lift is one of the oldest and most applied artificial lift methods especially for large oil fields, the gas that is required for injection is quite scarce and expensive resource, optimally allocating the injection rate in each well is a high importance task and not easily applicable. Conventional methods faced some major problems in solving this problem in a network with large number of wells, multi-constrains, multi-objectives, and limited amount of gas. This paper focuses on utilizing the Genetic Algorithm (GA) as a gas lift optimization algorithm to tackle the challenging task of optimally allocating the gas lift injection rate through numerical modeling and simulation studies to maximize the oil production of a Middle Eastern oil field with 20 production wells with limited amount of gas to be injected. The key objective of this study is to assess the performance of the wells of the field after applying gas lift as an artificial lift method and applying the genetic algorithm as an optimization algorithm while comparing the results of the network to the case of artificially lifted wells by utilizing ESP pumps to the network and to have a more accurate view on the practicability of applying the gas lift optimization technique. The comparison is based on different measures and sensitivity studies, reservoir pressure, and water cut sensitivity analysis are applied to allow the assessment of the performance of the wells in the network throughout the life of the field. To have a full and insight view an economic study and comparison was applied in this study to estimate the benefits of applying the gas lift method and the GA optimization technique while comparing the results to the case of the ESP pumps and the case of naturally flowing wells. The gas lift technique proved to have the ability to enhance the production of the oil field and the optimization process showed quite an enhancement in the task of maximizing the oil production rate while using the same amount of gas to be injected in the each well, the sensitivity analysis showed that the gas lift method is comparable to the other artificial lift method and it have an upper hand in handling the reservoir pressure reduction, and economically CAPEX of the gas lift were calculated to be able to assess the time to reach a profitable income by comparing the results of OPEX of gas lift the technique showed a profitable income higher than the cases of naturally flowing wells and the ESP pumps lifted wells. Additionally, the paper illustrated the genetic algorithm (GA) optimization model in a way that allowed it to be followed as a guide for the task of optimizing the gas injection rate for a network with a large number of wells and limited amount of gas to be injected.


2014 ◽  
Author(s):  
Hector Aguilar ◽  
Aref Almarzooqi ◽  
Tarek Mohamed El Sonbaty ◽  
Leigber Villarreal

Author(s):  
Eugenio Turco Neto ◽  
M. A. Rahman ◽  
Syed Imtiaz ◽  
Thiago dos Santos Pereira ◽  
Fernanda Soares de Sousa

The gas hydrates problem has been growing in offshore deep water condition where due to low temperature and high pressure hydrate formation becomes more favorable. Several studies have been done to predict the influence of gas hydrate formation in natural gas flow pipeline. However, the effects of multiphase hydrodynamic properties on hydrate formation are missing in these studies. The use of CFD to simulate gas hydrate formation can overcome this gap. In this study a computational fluid dynamics (CFD) model has been developed for mass, heat and momentum transfer for better understanding natural gas hydrate formation and its migration into the pipelines using ANSYS CFX-14. The problem considered in this study is a three-dimensional multiphase-flow model based on Simon Lo (2003) study, which considered the oil-dominant flow in a pipeline with hydrate formation around water droplets dispersed into the oil phase. The results obtained in this study will be useful in designing a multiphase flow metering and a pump to overcome the pressure drop caused by hydrate formation in multiphase petroleum production.


1982 ◽  
Vol 15 (12) ◽  
pp. 458-463 ◽  
Author(s):  
R. S. Medlock

Flow measurement has a long history extending over a period of about 3000 years, but it was only just over 200 years ago that the subject was first studied on a scientific basis and it was only 20 years ago that a surge of new techniques became available. Today there is a wide selection of methods and equipment to enable flow to be measured whether the medium is in the form of a liquid, gas, vapour or solid, or any combination thereof. According to the application, volumetric flow rate can be measured over a range exceeding 10−5m3/h to 106m3/h which in everday terms is equivalent to a cupful per day to the flow of a very large river. The price of a flowmeter can be as small as a few pounds or in excess of £1 million depending on the accuracy and capacity required. References are made to about 50 types of flow metering devices which can be classified into 11 groups.


Sign in / Sign up

Export Citation Format

Share Document