Experimental Study of Process Parameters through Dissimilar Form of Electrodes in EDM Machining

2017 ◽  
Author(s):  
D. G. Mahto ◽  
Narinder Singh
Keyword(s):  
Experimental Study ◽  
Process Parameters

Characterisation of the Femtosecond Laser Micro-Grooving Process for Germanium Substrates

2016 ◽  
Vol 874 ◽  
pp. 291-296 ◽  
Author(s):  
Lin Li ◽  
Jun Wang ◽  
Huai Zhong Li
Keyword(s):  
Experimental Study ◽  
Process Parameters ◽  
Material Removal ◽  
Removal Rate ◽  
High Quality ◽  
Scan Speed ◽  
Micro Grooving ◽  
Fs Laser ◽  
Selection Of ◽  
Germanium Substrates

An experimental study is reported to characterise the femtosecond (FS) laser grooving process for Germanium (Ge) substrates. The effects of process parameters, including laser fluence, pulse repetition rate and scan speed, on the groove characteristics, material removal rate (MRR) and heat affected zone (HAZ) size are discussed. It is shown that with properly selected process parameters, high quality micro-grooves can be obtained on Ge wafers. Recommendations are finally made on the selection of the most appropriate process parameters for FS micro-grooving of Ge substrates.

Experimental Study on Hot-air Drying Process Parameters Optimization of Chinese Jujubes

2013 ◽  
Vol 12 (21) ◽  
pp. 6154-6158
Author(s):  
Xiao Kang-Yi ◽  
Chuan Feng-Li ◽  
Shu Gang-Li ◽  
He Lei Cui ◽  
Wen Fu-Wu
Keyword(s):  
Experimental Study ◽  
Process Parameters ◽  
Parameters Optimization ◽  
Drying Process ◽  
Hot Air Drying ◽  
Air Drying ◽  
Process Parameters Optimization ◽  
Hot Air

Experimental Study on Critical Process Parameters Regarding Tension Stringing Construction of 1250mm2 Large-Section Conductor

2013 ◽  
Vol 448-453 ◽  
pp. 2036-2039
Author(s):  
Chun Hua Hu ◽  
Yong Jun Xia ◽  
Junz Hang Li
Keyword(s):  
Experimental Study ◽  
Process Parameters ◽  
Construction Process ◽  
Test Plan ◽  
Large Section ◽  
Critical Process Parameters ◽  
Critical Process ◽  
Test Rack

Critical construction process parameters and necessity of experimental study concerning tension stringing of large-section conductor are elaborated in this paper and in addition, test details related to critical process parameters of tension stringing construction is researched by citing the example of 1250mm2 large-section conductor, according to which test plan is worked out and test rack is designed.

An experimental study on the optimization of powder forging process parameters for an aluminum-alloy piston

2001 ◽  
Vol 113 (1-3) ◽  
pp. 486-492 ◽  
Author(s):  
Jong-Ok Park ◽  
Kil-Jun Kim ◽  
Dae-Yong Kang ◽  
Young-seog Lee ◽  
Young-Ho Kim
Keyword(s):  
Experimental Study ◽  
Aluminum Alloy ◽  
Process Parameters ◽  
Forging Process

Experimental study of the influence of the process parameters in the milling of Al6082-T6 alloy

2019 ◽  
Vol 34 (12) ◽  
pp. 1411-1427 ◽  
Author(s):  
M. Jebaraj ◽  
M. Pradeep Kumar ◽  
N. Yuvaraj ◽  
G. Mujibar Rahman
Keyword(s):  
Experimental Study ◽  
Process Parameters

Experimental Investigation and Parameter Optimization of Micro Holes Machining on Ti-6Al-4V Alloy

2015 ◽  
Vol 813-814 ◽  
pp. 332-336
Author(s):  
R.A. Aravind ◽  
Shivakumar Ganesh ◽  
Syed Mohammed Yasir ◽  
G. Madhan Mohan ◽  
Vijayan Krishnaraj ◽  
...  
Keyword(s):  
Experimental Study ◽  
Experimental Investigation ◽  
Process Parameters ◽  
Electric Discharge ◽  
Optimum Process ◽  
Grinding Process ◽  
Taguchi’S Method ◽  
Electro Discharge Machining ◽  
Micro Holes ◽  
Variance Approach

This paper presents an experimental study on the diametrical overcut and taper obtained during the machining of micro holes by electro-discharge machining (EDM). Many trials were taken by machining a 2.0 mm electrolytic copper rod to 0.50 mm under various conditions to analyse the effect of process parameters by wire electric discharge grinding process (WEDG). The optimum process parameters were determined by Taguchi’s method. Then a set of electrodes were produced with the determined optimum process parameters and were used to machine micro holes on Ti-6Al-4V alloy. The diameters of the holes were measured and the effects of various parameters were analysed for the variation in taper and diametrical overcut. The experimental results were analysed using analysis of variance approach.

An Experimental Study of the Effect of Shot Peening on the Low Carbon Steel and Identification of Optimal Process Parameters

2015 ◽  
Vol 2 (4-5) ◽  
pp. 3363-3370 ◽  
Author(s):  
Sirajuddin Elyas Khany ◽  
M.A. Moyeed ◽  
Md Shahabuddin Siddiqui ◽  
G.M. Sayeed Ahmed ◽  
M.M.A. Baig
Keyword(s):  
Experimental Study ◽  
Carbon Steel ◽  
Process Parameters ◽  
Shot Peening ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Optimal Process
Sign in / Sign up

Export Citation Format

Share Document