scholarly journals Air flow model development and application in a complex combined sewer system

2020 ◽  
Vol 82 (8) ◽  
pp. 1687-1700 ◽  
Author(s):  
Hasan Zobeyer ◽  
David Z. Zhu ◽  
Stephen Edwini-Bonsu
Keyword(s):  
Flow Rate ◽  
Flow Model ◽  
Air Flow ◽  
Model Development ◽  
Iterative Solution ◽  
Momentum Equation ◽  
Air Flow Rate ◽  
Sewer System ◽  
Combined Sewer ◽  
Combined Sewer System

Abstract A steady-state air flow model was developed and applied in a complex combined sewer system in the city of Edmonton, Alberta, Canada. The model solves the continuity at each junction and the momentum equation for the links coupled with dropshaft and other manholes. The dropshaft pressure gradient is computed using the dropshaft equation and air flow rate through manhole pickholes is computed considering the opening as an orifice. A leakage factor is used as a calibration parameter to represent the area through which air can leak from the manholes into the neighborhood. The model uses an iterative solution algorithm with a forward sweep for the continuity and backward sweep for the momentum equation. An underrelaxation is applied to update pressure in each iteration for model stability. The model was calibrated and validated by using the measured air flow rate and manhole pressure in the sewer network, with good results. An analysis of the air flow characteristics shows that a significant amount of air is brought into the system due to a large headspace in the upstream trunk but over 70% of this air is released into the neighborhood due to reduced headspace in the downstream trunk.

Improving the estimation of methodological errors in reproducing the volumetric air flow rate by reference critical nozzle

Metrologiya ◽  
2021 ◽  
pp. 4-30
Author(s):  
V. I. Chesnokov
Keyword(s):  
Kinetic Energy ◽  
Flow Rate ◽  
Gas Flow ◽  
Flow Model ◽  
Air Flow ◽  
Operating Conditions ◽  
Initial Kinetic Energy ◽  
Methodological Error ◽  
Air Flow Rate ◽  
Critical Nozzle

In the development of the previously obtained results a more accurate estimate of the methodological error in reproducing the volumetric air flow rate by reference critical nozzle is given, associated with the choice of the gas flow model and due to taking into account the initial kinetic energy of the flow at the nozzle inlet. Based on improved flow model an analytical evaluation of the methodological error in reproducing the volumetric air flow rate by reference critical nozzle, which is due to a change in the humidity of the working air, has been carried out. It is shown that the methodological error in reproducing the volumetric air flow rate by reference critical nozzle, associated with a change in the air humidity, as well as the analogies methodical error caused by the existence of the initial kinetic energy of the flow, must be taken part in accuracy characteristics at the real operating conditions of the standard volumetric air flow rate using critical nozzles.

scholarly journals Air Flow Model for Mixed-Mode and Indirect-Mode Natural Convection Solar Drying of Maize

2020 ◽  
Vol 10 (2) ◽  
pp. 1
Author(s):  
Isaac N. Simate
Keyword(s):  
Natural Convection ◽  
Flow Rate ◽  
Mixed Mode ◽  
Flow Model ◽  
Air Flow ◽  
Solar Drying ◽  
Air Flow Rate ◽  
Thermal Buoyancy ◽  
Early Stages ◽  
Grain Moisture

An air flow model for mixed-mode and indirect-mode natural convection solar drying of maize to help understand the factors that influence air flow in the dryer is presented. Temperatures at various sections of the dryer obtained from drying experiments were input to the air flow model to predict the respective thermal buoyancies. The air flow rate was determined by balancing the sum of the buoyancy pressures with the sum of the flow resistances in the various sections of the dryer. To validate the model, the predicted air flow was compared with measured air flow from experiments. For both the mixed-mode and indirect-mode, the biggest driver of the air flow is the thermal buoyancy created in the collector, while the grain bed is the dominant pressure drop. Thermal buoyancy on top of the grain bed is largely responsible for the variation in air flow, translating into low mass air flow during the early stages of drying when grain moisture is high, and higher air flow in the later stages when grain moisture is low. The heating of the grain bed by direct radiation in the mixed-mode translates into a slightly higher air flow rate than the indirect-mode. The implications are that a thinner grain bed results in shorter drying time as it has a higher air flow rate than a thicker one. To mitigate the low air flow at the early stages of drying, the collector length should be appropriately designed for a desired air flow.

scholarly journals Model of thermal buoyancy in cavity-ventilated roof constructions

2021 ◽  
pp. 174425912098418
Author(s):  
Toivo Säwén ◽  
Martina Stockhaus ◽  
Carl-Eric Hagentoft ◽  
Nora Schjøth Bunkholt ◽  
Paula Wahlgren
Keyword(s):  
Analytical Model ◽  
Flow Rate ◽  
Numerical Study ◽  
Air Flow ◽  
Wind Pressure ◽  
Air Flow Rate ◽  
Test Set ◽  
Air Cavity ◽  
Thermal Buoyancy ◽  
The Impact

Timber roof constructions are commonly ventilated through an air cavity beneath the roof sheathing in order to remove heat and moisture from the construction. The driving forces for this ventilation are wind pressure and thermal buoyancy. The wind driven ventilation has been studied extensively, while models for predicting buoyant flow are less developed. In the present study, a novel analytical model is presented to predict the air flow caused by thermal buoyancy in a ventilated roof construction. The model provides means to calculate the cavity Rayleigh number for the roof construction, which is then correlated with the air flow rate. The model predictions are compared to the results of an experimental and a numerical study examining the effect of different cavity designs and inclinations on the air flow rate in a ventilated roof subjected to varying heat loads. Over 80 different test set-ups, the analytical model was found to replicate both experimental and numerical results within an acceptable margin. The effect of an increased total roof height, air cavity height and solar heat load for a given construction is an increased air flow rate through the air cavity. On average, the analytical model predicts a 3% higher air flow rate than found in the numerical study, and a 20% lower air flow rate than found in the experimental study, for comparable test set-ups. The model provided can be used to predict the air flow rate in cavities of varying design, and to quantify the impact of suggested roof design changes. The result can be used as a basis for estimating the moisture safety of a roof construction.

scholarly journals Modeling and optimization of radish root extract drying as peroxidase source using spouted bed dryer

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Shahrbanoo Hamedi ◽  
M. Mehdi Afsahi ◽  
Ali Riahi-Madvar ◽  
Ali Mohebbi
Keyword(s):  
Kinetic Parameters ◽  
Flow Rate ◽  
Air Flow ◽  
Cost Effective ◽  
Industrial Applications ◽  
Interactive Effects ◽  
Root Extract ◽  
Air Flow Rate ◽  
Spouted Bed ◽  
Radish Root

AbstractThe main advantages of the dried enzymes are the lower cost of storage and longer time of preservation for industrial applications. In this study, the spouted bed dryer was utilized for drying the garden radish (Raphanus sativus L.) root extract as a cost-effective source of the peroxidase enzyme. The response surface methodology (RSM) was used to evaluate the individual and interactive effects of main parameters (the inlet air temperature (T) and the ratio of air flow rate to the minimum spouting air flow rate (Q)) on the residual enzyme activity (REA). The maximum REA of 38.7% was obtained at T = 50 °C and Q = 1.4. To investigate the drying effect on the catalytic activity, the optimum reaction conditions (pH and temperature), as well as kinetic parameters, were investigated for the fresh and dried enzyme extracts (FEE and DEE). The obtained results showed that the optimum pH of DEE was decreased by 12.3% compared to FEE, while the optimum temperature of DEE compared to FEE increased by a factor of 85.7%. Moreover, kinetic parameters, thermal-stability, and shelf life of the enzyme were considerably improved after drying by the spouted bed. Overall, the results confirmed that a spouted bed reactor can be used as a promising method for drying heat-sensitive materials such as peroxidase enzyme.

Method to Determine an Optimal Air-Flow Rate in Solar Collectors

1979 ◽  
Vol 3 (6) ◽  
pp. 357-362
Author(s):  
H. C. Hewitt ◽  
E. I. Griggs
Keyword(s):  
Flow Rate ◽  
Air Flow ◽  
Solar Collectors ◽  
Air Flow Rate
Sign in / Sign up

Export Citation Format

Share Document