scholarly journals A Constitutive Structural Parameter for the Work Hardening Behavior of Additively Manufactured Ti-6Al-4V.

2021 ◽  
Author(s):  
Alan Jankowski
Keyword(s):  
Work Hardening ◽  
Structural Parameter ◽  
Work Hardening Behavior ◽  
Hardening Behavior

Stir zone anisotropic work hardening behavior in friction stir processed EN8 medium carbon steel

2020 ◽  
pp. 140582
Author(s):  
Md Anwar Ali Anshari ◽  
Murshid Imam ◽  
Mohd Zaheer Khan Yusufzai ◽  
Viswanath Chinthapenta ◽  
Rajnish Mishra
Keyword(s):  
Carbon Steel ◽  
Work Hardening ◽  
Medium Carbon Steel ◽  
Stir Zone ◽  
Medium Carbon ◽  
Work Hardening Behavior ◽  
Friction Stir ◽  
Hardening Behavior

Effect of Sc addition on the work-hardening behavior of ZK60 magnesium alloy

2013 ◽  
Vol 43 ◽  
pp. 572-577 ◽  
Author(s):  
Tingting Liu ◽  
Fusheng Pan ◽  
Xiyan Zhang
Keyword(s):  
Magnesium Alloy ◽  
Work Hardening ◽  
Work Hardening Behavior ◽  
Hardening Behavior ◽  
Sc Addition ◽  
Zk60 Magnesium Alloy

Rate sensitivity and work-hardening behavior of an advanced Ti-Al-N alloy under uniaxial tensile loading

2019 ◽  
Vol 744 ◽  
pp. 630-637 ◽  
Author(s):  
Jianghua Shen ◽  
Biao Chen ◽  
Junko Umeda ◽  
Jiong Zhang ◽  
Yulong Li ◽  
...  
Keyword(s):  
Work Hardening ◽  
Rate Sensitivity ◽  
Tensile Loading ◽  
Uniaxial Tensile ◽  
Work Hardening Behavior ◽  
Hardening Behavior ◽  
Uniaxial Tensile Loading

scholarly journals Machining-Induced Work Hardening Behavior of Inconel 718 Considering Edge Geometries

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 397
Author(s):  
Bin Zhou ◽  
Weiwei Zhang ◽  
Zhongmei Gao ◽  
Guoqiang Luo
Keyword(s):  
Grain Size ◽  
Work Hardening ◽  
Inconel 718 ◽  
Orthogonal Cutting ◽  
Chip Thickness ◽  
Machined Surface ◽  
Work Hardening Behavior ◽  
Hardening Behavior ◽  
Significant Difference ◽  
Optimization Of Cutting Parameters

As a representative type of superalloy, Inconel 718 is widely employed in aerospace, marine and nuclear industries. The significant work hardening behavior of Inconel 718 can improve the service performance of components; nevertheless, it cause extreme difficulty in machining. This paper aims to investigate the influence of chamfered edge parameters on work hardening in orthogonal cutting of Inconel 718 based on a novel hybrid method, which integrates Coupled Eulerian-Lagrangian (CEL) method and grain-size-based functions considering the influence of grain size on microhardness. Orthogonal cutting experiments and nanoindentation tests are conducted to validate the effectiveness of the proposed method. The predicted results are highly consistent with the experimental results. The depth of work hardening layer increases with increasing chamfer angle and chamfer width, also with increasing feed rate (the uncut chip thickness). However, the maximum microhardness on the machined surface does not exhibit a significant difference. The proposed method can provide theoretical guidance for the optimization of cutting parameters and improvement of the work hardening.

Influence of Zn addition on the microstructure, tensile properties and work-hardening behavior of Mg-1Gd alloy

2020 ◽  
Vol 772 ◽  
pp. 138779 ◽  
Author(s):  
Jun Zhao ◽  
Bin Jiang ◽  
Yuan Yuan ◽  
Aitao Tang ◽  
Haoran Sheng ◽  
...  
Keyword(s):  
Tensile Properties ◽  
Work Hardening ◽  
Work Hardening Behavior ◽  
Hardening Behavior ◽  
Zn Addition

Localized Deformation of Equal Channel Angular Extruded Aluminum

2005 ◽  
Vol 475-479 ◽  
pp. 425-428 ◽  
Author(s):  
Fuqian Yang ◽  
Lingling Peng ◽  
Kenji Okazaki
Keyword(s):  
Work Hardening ◽  
Deformation Behavior ◽  
Master Curve ◽  
Localized Deformation ◽  
Stress Strain ◽  
Work Hardening Behavior ◽  
Hardening Behavior ◽  
Similar Work

The localized deformation behavior of annealed Al and Al severely deformed by ECAE process was determined by using microindentation test. Using the method proposed by Tabor, the indentation stress-strain curves of annealed Al and as-ECAE deformed Al were constructed, which display similar work-hardening behavior. For annealed Al, the altitude of the indentation stressstrain curves is a function of the indenter size. A master curve then is constructed, which displays different work-hardening behavior. For the ECAE deformed Al, the indentation stress-strain curves are independent of the indenter size, suggesting that the microstructure inside the as-ECAE deformed Al is different from the annealed Al.

Tensile flow and work-hardening behavior of a Ti-modified austenitic stainless steel

1997 ◽  
Vol 28 (1) ◽  
pp. 171-178 ◽  
Author(s):  
P. V. Sivaprasad ◽  
S. Venugopal ◽  
S. Venkadesan
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Work Hardening ◽  
Work Hardening Behavior ◽  
Hardening Behavior

Microstructures, tensile properties and work hardening behavior of SiCp/Mg-Zn-Ca composites

2017 ◽  
Vol 695 ◽  
pp. 2215-2223 ◽  
Author(s):  
Wei-jian Li ◽  
Kun-kun Deng ◽  
Xiao Zhang ◽  
Cui-ju Wang ◽  
Jin-wen Kang ◽  
...  
Keyword(s):  
Tensile Properties ◽  
Work Hardening ◽  
Work Hardening Behavior ◽  
Hardening Behavior
Sign in / Sign up

Export Citation Format

Share Document