scholarly journals Interpretasi Praktis Terhadap Istilah-Istilah Daya pada Rangkaian Listrik Satu Fase Sinusoidal

2021 ◽  
Vol 1 (1) ◽  
Author(s):  
Adlan Bagus Pradana ◽  
Unan Yusmaniar Oktiawati ◽  
Jimmy Trio Putra ◽  
Dhanis Woro Fittrin Selo Nur Giyatno ◽  
Atikah Surriani
Keyword(s):  
Computer Simulations ◽  
Daily Activity ◽  
Power Analysis ◽  
Single Phase ◽  
Reactive Power ◽  
Electrical Engineering ◽  
Active Power ◽  
General Application ◽  
Instantaneous Power ◽  
Complex Power

In electrical engineering, there are several power terms; active power, reactive power, instantaneous active power, instantaneous active power, instantaneous power, apparent power and complex power. Even though are used in daily activity, electrical practitioners are facing difficulty to explain those terms practically. This paper tries to solve those difficulty by interpret those term in practical way. Firstly, each power term are defined theoretically. Then those terms are presented mathematically. Next, power in single phase sinusoidal electric network is analyzed. Theoretical definition result is connected with power analysis result. Computer simulations are held to strengthen interpretation result. Considering the width of discussion area, this paper only covers most general application, that is single phase sinusoidal network.

scholarly journals HIL-Assessed Fast and Accurate Single-Phase Power Calculation Algorithm for Voltage Source Inverters Supplying to High Total Demand Distortion Nonlinear Loads

Electronics ◽  
2020 ◽  
Vol 9 (10) ◽  
pp. 1643
Author(s):  
Jorge El Mariachet ◽  
Yajuan Guan ◽  
Jose Matas ◽  
Helena Martín ◽  
Mingshen Li ◽  
...  
Keyword(s):  
Steady State ◽  
Single Phase ◽  
Reactive Power ◽  
Dynamic Performance ◽  
Active Power ◽  
Voltage Source ◽  
Power Calculation ◽  
Calculation Algorithm ◽  
Nonlinear Loads ◽  
Voltage Source Inverters

The dynamic performance of the local control of single-phase voltage source inverters (VSIs) can be degraded when supplying to nonlinear loads (NLLs) in microgrids. When this control is based on the droop principles, a proper calculation of the active and reactive averaged powers (P–Q) is essential for a proficient dynamic response against abrupt NLL changes. In this work, a VSI supplying to an NLL was studied, focusing the attention on the P–Q calculation stage. This stage first generated the direct and in-quadrature signals from the measured load current through a second-order generalized integrator (SOGI). Then, the instantaneous power quantities were obtained by multiplying each filtered current by the output voltage, and filtered later by utilizing a SOGI to acquire the averaged P–Q parameters. The proposed algorithm was compared with previous proposals, while keeping the active power steady-state ripple constant, which resulted in a faster calculation of the averaged active power. In this case, the steady-state averaged reactive power presented less ripple than the best proposal to which it was compared. When reducing the velocity of the proposed algorithm for the active power, it also showed a reduction in its steady-state ripple. Simulations, hardware-in-the-loop, and experimental tests were carried out to verify the effectiveness of the proposal.

scholarly journals Inactive power detection in AC network

2021 ◽  
Vol 11 (2) ◽  
pp. 966
Author(s):  
Nickolay I. Schurov ◽  
Sergey V. Myatezh ◽  
Alexandr V. Myatezh ◽  
Boris V. Malozyomov ◽  
Alexandr A. Shtang
Keyword(s):  
Reactive Power ◽  
Power Level ◽  
Phase Shifts ◽  
Active Power ◽  
Power Balance ◽  
Stationary Mode ◽  
Instantaneous Power ◽  
Methodological Errors ◽  
The Future ◽  
Ac Networks

Using the examples of wave and vector diagrams, we study the conditions for the appearance of components of inactive power in an AC network, which are known as reactive power and distortion power. It is shown that the components of the active, reactive power and distortion power are mutually orthogonal and form a power balance, which can be violated mainly due to methodological errors in calculating these components under conditions of non-stationary mode parameters. It is established that the interaction of reactive power and distortion power occurs at the instantaneous power level, and changing their phase shifts allows you to adjust the shape of the resulting power without involving additional active power in the AC network. The results obtained will allow not only to correctly determine the proportion and nature of the components of inactive capacities, which is valuable for solving the problems of optimizing modes in AC networks, but also to create effective technical means of compensating for the identified inactive capacities in the future.

Application of Novel Techniques in Active Power Filter

2020 ◽  
pp. 158-191
Author(s):  
Karunendra Kumar Verma ◽  
V. M. Mishra ◽  
Niraj Kumar
Keyword(s):  
Single Phase ◽  
Reactive Power ◽  
Supply Voltage ◽  
Semiconductor Devices ◽  
Active Power Filter ◽  
Active Power ◽  
Current Control ◽  
Active Power Filters ◽  
Power Filter ◽  
Power Filters

Traditionally, the major part of the electrical power is generally consumed by the non-linear loads due to frequent application of the semiconductor devices in the form of domestic and industrial loads. This results from distortion in the actual supply voltage waveform at the source end due to the interference of the multiple harmonics generated out of semiconductor devices used at load end and excessive absorption of the reactive power. The insufficiency of these compensation techniques leads to the advent of the phase multiplication techniques as well as the most reliable and economic active power filtering scheme. A deep analysis showing tedious waveforms using the ORCAD simulation package for the various kind of loads in conjunction with the single-phase active power filter shunted to the single-phase line at the load end for the two current control techniques (i.e., hysteresis band current control, triangularization of current control) has been done. The results are analyzed and tested to lead the optimistic approach for APF (active power filters).

A New Definition of Non-Active Power

2006 ◽  
Vol 7 (4) ◽  
Author(s):  
Harnaak Khalsa ◽  
Jingxin Zhang
Keyword(s):  
Energy Transfer ◽  
Unique Solution ◽  
Single Phase ◽  
Active Power ◽  
Instantaneous Power ◽  
Unique Definition ◽  
Phase Systems ◽  
Definition Of

There is no unique definition of non-active power for nonsinusoidal systems. A new definition of non-active power is proposed in this paper. This definition is based on energy transfer and provides a unique solution for non-active power of single-phase systems under both sinusoidal and non-sinusoidal conditions. An example is used to illustrate the use of this new definition. Energy transfer calculated using the new definition provides the same energy transfer determined from the non-sinusoidal non-active instantaneous power. This is consistent with the existing definition of active power that is also based on energy transfer.

scholarly journals Interphase Power Flow Control via Single-Phase Elements in Distribution Systems

2021 ◽  
Vol 3 (1) ◽  
pp. 37-58
Author(s):  
Piyapath Siratarnsophon ◽  
Vinicius C. Cunha ◽  
Nicholas G. Barry ◽  
Surya Santoso
Keyword(s):  
Power Consumption ◽  
Power Systems ◽  
Power Flow ◽  
Distribution Systems ◽  
Single Phase ◽  
Reactive Power ◽  
Active Power ◽  
Real Power ◽  
Power Flow Control ◽  
Reactive Power Flow

The capability of routing power from one phase to another, interphase power flow (IPPF) control, has the potential to improve power systems efficiency, stability, and operation. To date, existing works on IPPF control focus on unbalanced compensation using three-phase devices. An IPPF model is proposed for capturing the general power flow caused by single-phase elements. The model reveals that the presence of a power quantity in line-to-line single-phase elements causes an IPPF of the opposite quantity; line-to-line reactive power consumption causes real power flow from leading to lagging phase while real power consumption causes reactive power flow from lagging to leading phase. Based on the model, the IPPF control is proposed for line-to-line single-phase power electronic interfaces and static var compensators (SVCs). In addition, the control is also applicable for the line-to-neutral single-phase elements connected at the wye side of delta-wye transformers. Two simulations on a multimicrogrid system and a utility feeder are provided for verification and demonstration. The application of IPPF control allows single-phase elements to route active power between phases, improving system operation and flexibility. A simple IPPF control for active power balancing at the feeder head shows reductions in both voltage unbalances and system losses.

Sign in / Sign up

Export Citation Format

Share Document