scholarly journals Potential usage of fly and bottom ash from thermal power plant ”Nikola Tesla” landfill, Serbia

2012 ◽  
Vol 66 (3) ◽  
pp. 403-412 ◽  
Author(s):  
Miodrag Zivotic ◽  
Dragoslava Stojiljkovic ◽  
Aleksandar Jovovic ◽  
Vladica Cudic
Keyword(s):  
Power Plant ◽  
Thermal Power Plant ◽  
Power Plants ◽  
Thermal Power ◽  
Bottom Ash ◽  
Raw Material ◽  
Steel Mill ◽  
Waste Discharge ◽  
Nikola Tesla ◽  
Cement Mixture

In Serbia, the ash from power plants has long been labelled as hazardous waste. With the adoption of the appropriate legislation this ash became secondary raw material with the potential usage. In this paper an analysis of the fly and bottom ash composition, which are disposed of in the power plant ?Nikola Tesla A? landfill, is presented. Thirty samples, divided into three sets, were analyzed for trace elements As, Ba, Be, Cd, Co, Cr, Cu, Mn, Mo, Ni, Pb, Ti, V and Zn. The first and second set of samples were taken at the depth of 0.0-0.6 m, from cassette III, at the place of waste discharge (set I) and in the centre of the cassette (set II).The third set of samples was taken from the same cassette spot but at the different depth. The estimated variations in quality within individual sets, as well as the comparison between sets I and II, were done. The repeatability of results by the depth of cassette (set III) was also analyzed. The mixture consisting of 79.4% limestone, 17% clay, 0.5% sand, 0.55% iron ore, 0.55% from steel mill waste and 2% ash from the thermal power plant "Nikola Tesla A" was adopted as the reputable mixture for cement making. For concrete making, the same cement mixture was used but with 2.1% of the same ash material added. The results showed possibility of further fly and bottom ash use as the cement and concrete material.

Compressive Strength and Density of Cementless Unfired Lightweight Brick Utilizing Coal Ash from Coal-Fired Thermal Power Plant

2013 ◽  
Vol 594-595 ◽  
pp. 527-531
Author(s):  
Mohamad Ezad Hafez Mohd Pahroraji ◽  
Hamidah Mohd Saman ◽  
Mohamad Nidzam Rahmat ◽  
Kartini Kamaruddin ◽  
Ahmad Faiz Abdul Rashid
Keyword(s):  
Compressive Strength ◽  
Power Plant ◽  
Thermal Power Plant ◽  
Thermal Power ◽  
Bottom Ash ◽  
Coal Ash ◽  
Hydrated Lime ◽  
Raw Material ◽  
The World ◽  
Blastfurnace Slag

Millions tons of coal ash which constitute of fly ash and bottom ash were produced annually throughout the world. They were significant to be developed as masonry brick to substitute the existing widely used traditional material such as clay and sand brick which were produced from depleting and dwindling natural resources. In the present study, the coal ash from coal-fired thermal power plant was used as the main raw material for the fabrication of cementless unfired lightweight brick. The binder comprising of Hydrated Lime (HL)-activated Ground Granulated Blastfurnace Slag (GGBS) system at binding ratio 30:70, 50:50 and 70:30 were used to stabilize the coal ash in the fabrication process of the brick. Foam was used to lightweight the brick. The compressive strength and ambient density were evaluated on the brick. The results indicated that the brick incorporating HL-GGBS system achieved higher strength of 20.84N/mm2 at 28 days compare to the HL system with strength of 13.98N/mm2 at 28 days. However, as the quantity of foam increase at 0%, 25%, 50%, 75% and 100%, the strength and density for the brick decreased.

Supplier Selection Criterion for SSCM in Indian Thermal Power Plant

2019 ◽  
pp. 240-257
Author(s):  
Suchismita Satapathy
Keyword(s):  
Power Plant ◽  
Thermal Power Plant ◽  
Power Plants ◽  
Thermal Power ◽  
Selection Criterion ◽  
Raw Material ◽  
Thermal Power Plants ◽  
Whole Process ◽  
Main Motive

All companies are dependent on their raw material providers. The same applies in the case of thermal power plants. The major raw material for a thermal power plant is the coal. There are a lot of companies which in turn provide this coal to the thermal power plant. Some of these companies are international; some are local, whereas the others are localized. The thermal power plants look into all the aspects of the coal providing company, before settling down for a deal. Some people are specifically assigned to the task of managing the supply chain. The main motive is to optimize the whole process and achieve higher efficiency. There are a lot of things which a thermal power plant looks into before finalizing a deal, such as the price, quality of goods, etc. Thus, it is very important for the raw material providers to understand each and every aspect of the demands of the thermal power plant. A combination of three methods—Delphi, SWARA, and modified SWARA—has been applied to a list of factors, which has later been ranked according to the weight and other relevant calculations.

scholarly journals Fly ash and slag utilization for the Serbian railway substructure

Transport ◽  
2016 ◽  
Vol 33 (2) ◽  
pp. 389-398 ◽  
Author(s):  
Mirjana Vukićević ◽  
Zdenka Popović ◽  
Jovan Despotović ◽  
Luka Lazarević
Keyword(s):  
Fly Ash ◽  
Power Plant ◽  
Thermal Power Plant ◽  
Power Plants ◽  
Thermal Power ◽  
Cement Industry ◽  
Engineering Properties ◽  
Thermal Power Plants ◽  
Nikola Tesla ◽  
Railway Substructure

Approximately 7 million tons of fly ash and slag are produced in thermal power plants in Serbia every year, only 3% of which is used in the cement industry. About 300 million tons of the ash-slag mixture are disposed in landfills, occupying an area of approximately 1600 hectares and generating environmental issues. Fly ash from Serbian power plants has pozzolanic properties and due to low concentration of calcium compounds (less than 10% CaO), they do not have self-cementing properties. According to the ASTM C618-15, this ash is from class F. According to the European Standard EN 197-1:2011, this ash is siliceous (type V) ash. From April 2014 to May 2015, an investigation of engineering properties of fly ash and mixtures of fly ash and slag from landfill (without or with binders of cement/lime) was conducted at the Laboratory of Soil Mechanics at the Faculty of Civil Engineering of the University of Belgrade (Serbia) and at the Institute for Testing of Materials – IMS Institute in Belgrade. The laboratory test results were showed in the study ‘Utilization of fly ash and slag produced in the TPP JP EPS thermal power plants for construction of railways’. Four kinds of waste materials from Serbian power plants were laboratory tested: (a) an ash-slag mixture from landfills at the ‘Nikola Tesla A’ thermal power plant; (b) fly ash from silos in the ‘Nikola Tesla B’ thermal power plant; (c) an ash-slag mixture from landfills at the ‘Kostolac A’ and ‘Kostolac B’ thermal power plants and ‘Srednje kostolačko ostrvo’ landfill; (d) fly ash from the ‘Kostolac’ thermal power plant. The following physical and mechanical properties of ash and mixtures were investigated: grain size distribution, Atterberg limits, specific gravity, moisture-density relationship, shear strength parameters in terms of effective stresses, California Bearing Ratio (CBR), and deformation parameters. The paper presents the results of laboratory tests of the materials with and without binders, and based on the laboratory results and previous research, the paper presents possibilities of using fly ash and slag for the construction of railway substructure in the planned construction and reconstruction of railway network in Serbia. The obtained results indicate that tested fly ash and ash-slag mixture have met the technical requirements and that they have the potential to be used in railway substructure.

Bottom Ash from Mineral Coal as Aggregatein Mixtures for Ceramic Products

2014 ◽  
Vol 798-799 ◽  
pp. 599-604
Author(s):  
Nancy E. Quaranta ◽  
Marta G. Caligaris ◽  
Miguel A. Unsen ◽  
Hugo A. López ◽  
Gisela G. Pelozo
Keyword(s):  
Power Plant ◽  
Optical Microscopy ◽  
Thermal Power Plant ◽  
Thermal Power ◽  
Bottom Ash ◽  
Waste Material ◽  
Raw Material ◽  
Scanning Electronic Microscopy ◽  
Electronic Microscopy ◽  
Thermally Treated

The objective of this work is to analyze ashes from a thermal power plant with the aim of determining its environmental aptitude for reutilization as aggregates in clay mixtures for ceramics production. To achieve this objective the waste material was characterized by different techniques: optical microscopy, scanning electronic microscopy, conductivity, pH, among others. Clay samples with bottom ash addition, up to 50%, were prepared. These samples were thermally treated at 950oC and then characterized with diverse techniques in order to determine their behaviour in service. The obtained results show the high feasibility of reutilization of the studied waste as raw material in the production of ceramic products.

Nonlinear Trend Analysis of Mill Fan System Vibrations for Predictive Maintenance and Diagnostics

2012 ◽  
Vol 58 (4) ◽  
pp. 351-356
Author(s):  
Mincho B. Hadjiski ◽  
Lyubka A. Doukovska ◽  
Stefan L. Kojnov
Keyword(s):  
Power Plant ◽  
Trend Analysis ◽  
Thermal Power Plant ◽  
Power Plants ◽  
Thermal Power ◽  
Balkan Peninsula ◽  
Predictive Maintenance ◽  
Nonlinear Trend ◽  
The Subject ◽  
The Given

Abstract Present paper considers nonlinear trend analysis for diagnostics and predictive maintenance. The subject is a device from Maritsa East 2 thermal power plant a mill fan. The choice of the given power plant is not occasional. This is the largest thermal power plant on the Balkan Peninsula. Mill fans are main part of the fuel preparation in the coal fired power plants. The possibility to predict eventual damages or wear out without switching off the device is significant for providing faultless and reliable work avoiding the losses caused by planned maintenance. This paper addresses the needs of the Maritsa East 2 Complex aiming to improve the ecological parameters of the electro energy production process.

FLY ASH FROM THERMAL POWER PLANT, RAW MATERIAL FOR GLASS-CERAMIC

2013 ◽  
Vol 12 (2) ◽  
pp. 337-342 ◽  
Author(s):  
Firuta Goga ◽  
Roxana Dudric ◽  
Calin Cormos ◽  
Florica Imre ◽  
Liliana Bizo ◽  
...  
Keyword(s):  
Fly Ash ◽  
Power Plant ◽  
Glass Ceramic ◽  
Thermal Power Plant ◽  
Thermal Power ◽  
Raw Material ◽  
Plant Raw Material

Features of antibodies against benzo[a]pyrene formation in workers of coal mines and thermal power plants

2019 ◽  
pp. 9-14
Author(s):  
Ye. G. Polenok ◽  
S. A. Mun ◽  
L. A. Gordeeva ◽  
A. A. Glushkov ◽  
M. V. Kostyanko ◽  
...  
Keyword(s):  
Power Plant ◽  
Thermal Power Plant ◽  
Power Plants ◽  
Reference Group ◽  
Coal Dust ◽  
Thermal Power ◽  
Coal Mines ◽  
Serum Levels ◽  
Thermal Power Plants ◽  
Immune Reactions

Introduction.Coal dust and coal fi ring products contain large amounts of carcinogenic chemicals (specifically benz[a]pyrene) that are different in influence on workers of coal mines and thermal power plants. Specific immune reactions to benz[a]pyrene therefore in these categories of workers can have specific features.Objective.To reveal features of antibodies specifi c to benz[a]pyrene formation in workers of coal mines and thermal power plants.Materials and methods.The study covered A and G class antibodies against benz[a]pyrene (IgA-Bp and IgG-Bp) in serum of 705 males: 213 donors of Kemerovo blood transfusion center (group 1, reference); 293 miners(group 2) and 199 thermal power plant workers (group 3). Benz[a]pyrene conjugate with bovine serum albumin as an adsorbed antigen was subjected to immune-enzyme assay.Results.IgA-Bp levels in the miners (Me = 2.7) did not differ from those in the reference group (Me = 2.9), but in the thermal power plant workers (Me = 3.7) were reliably higher than those in healthy men and in the miners (p<0.0001). Levels of IgG-Bp in the miners (Me = 5.0) appeared to be lower than those in the reference group (Me = 6.4; (p = 0.05). IgG-Bb level in the thermal power plantworkers (Me = 7.4) exceeded the parameters in the healthy donors and the miners (p<0.0001). Non-industrial factors (age and smoking) appeared tohave no influence on specific immune reactions against benz[a]pyrene in the miners and the thermal power plant workers.Conclusions.Specific immune reactions against benz[a]pyrene in the miners and the thermal power plant workers are characterized by peculiarities: the miners demonstrate lower levels of class A serum antibodies to benz[a]pyrene; the thermal power plant workers present increased serum levels of class G antibodies to benz[a]pyrene. These peculiarities result from only the occupational features, but do not depend on such factors as age, smoking and length of service at hazardous production. It is expedient to study specific immune reactions to benz[a]pyrene in workers of coal mines and thermal power plants, to evaluate individual oncologic risk and if malignancies occur.

scholarly journals A GIS Based Approach for Radiation Risk Assessment Around a Thermal Power Plant Towards Adopting Remedial Measures

2018 ◽  
Author(s):  
Kajori Parial ◽  
S. Mukherjee ◽  
A. R. Ghosh ◽  
D. Sengupta
Keyword(s):  
Power Plant ◽  
Thermal Power Plant ◽  
Power Plants ◽  
Thermal Power ◽  
Radiation Risk ◽  
Surface Radiation ◽  
Radiation Hazard ◽  
Remedial Measures ◽  
Ancillary Data ◽  
Risk Zone

Coal combustion in thermal power plants releases ash. Ash is reported to cause different adverse health hazards in humans and other organisms. Owing to the presence of radionuclides, it is also considered as a potential radiation hazard. In this study, based on the surface radiation measurements and relevant ancillary data, expected radiation risk zones were identified with regard to the human population residing near the Thermal Power Plant. With population density as the risk determining criteria, about 20% of the study area was at &lsquo;High&rsquo; risk and another 20% of the study area was at &lsquo;Low&rsquo; risk zone. The remaining 60% was under medium risk zone. Based on the findings remedial measures which may be adopted have been suggested.

SANITARY PROTECTION ZONES BY NOISE FACTOR FROM GAS DISTRIBUTION POINTS

Akustika ◽  
2021 ◽  
pp. 133-137
Author(s):  
Vladimir Tupov ◽  
Vitaliy Skvortsov
Keyword(s):  
Power Plant ◽  
Natural Gas ◽  
Thermal Power Plant ◽  
Power Plants ◽  
Thermal Power ◽  
Design Stage ◽  
Thermal Power Plants ◽  
Gas Distribution ◽  
Surrounding Area ◽  
Protection Zone

The power equipment of thermal power plants is a source of noise to the surrounding area. One of the sources of noise for the surrounding area are gas distribution points (GDP) of thermal power plants (TPP) and district thermal power plants (RTS). Noise from gas distribution points may exceed sanitary standards at the border of the sanitary protection zone. The article shows that the radiated noise from gas distribution points depends on the power of the thermal power plant (natural gas consumption) and the type of valves. Three types of valves used in gas distribution points are considered. Formulas are obtained for calculating the width of the sanitary protection zone for gas distribution points for thermal stations, depending on the consumption of natural gas (electric power of the thermal power plant) and the type of valve. It is shown that, depending on the valve used, the noise level at the border of the sanitary protection zone can either meet sanitary standards or exceed them. This allows at the design stage to select the required type of valve or to determine mitigation measures from hydraulic fracturing.

Sign in / Sign up

Export Citation Format

Share Document