scholarly journals Numerical investigation of fluid flow and heat transfer characteristics in sine, triangular, and arc-shaped channels

2007 ◽  
Vol 11 (1) ◽  
pp. 17-26 ◽  
Author(s):  
Zakir Hossain ◽  
Sadrul Islam
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Fluid Flow ◽  
Critical Reynolds Number ◽  
Navier Stokes ◽  
Heat Transfer Characteristics ◽  
Single Wave ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer ◽  
Wavy Channels

Time dependent Navier-Stokes and energy equations have been solved to investigate the fluid flow and heat transfer characteristics in wavy channels. Three different types of two dimensional wavy geometries (e.g. sine-shaped, triangular, and arc-shaped) are considered. All of them are of single wave and have same geometric dimensions. Periodic boundary conditions are used to attain fully developed flow. The flow in the channels has been observed to be steady up to a critical Reynolds number, which depends on the geometric configuration. Beyond the critical Reynolds number a self-sustained oscillatory flow has been observed. As a result of this oscillation, there is increased mixing between core and the near-wall fluids, thereby increasing the heat transfer rate. For the same geometric dimensions, flow becomes unsteady at relatively lower Reynolds number in the arc-shaped channel. .

The Effect of the Corrugation Rib Angle of Attack on the Fluid Flow and Heat Transfer Characteristics Inside Corrugated Ribbed Passage

2011 ◽  
Vol 133 (8) ◽  
Author(s):  
A. M. I. Mohamed ◽  
R. Hoettiba ◽  
A. M. Saif
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Heat Transfer Enhancement ◽  
Angle Of Attack ◽  
Navier Stokes ◽  
Transfer Enhancement ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer ◽  
Flow Field Characteristics

Heat transfer enhancement using corrugated ribbed passages is one of the common enhancement techniques inside heat exchangers. The present study investigated numerically the effect of the corrugation rib angle of attack on the fluid flow and heat transfer characteristics inside the corrugated ribbed passage. The commercial computational fluid dynamics code PHOENICS 2006 was used to perform the numerical analysis by solving the Navier–Stokes and energy equations. The experimental part of this study was used only to validate the numerical model, and a good agreement between the experimental results and the model was obtained. The flow field characteristics and heat transfer enhancement were numerically investigated for different corrugated rib angles of attack as follows: 90 deg, 105 deg, 120 deg, 135 deg, and 150 deg. The corrugation rib angle of attack has a great effect on the reversed flow zone, the flow reattachments, and the enhancement of the heat transfer coefficient through the duct. The recommended rib angle of attack, which gives the optimum thermohydraulic performance, is found to be between 135 deg and 150 deg. The value of the maximum thermohydraulic performance is about 3.6 for the 150 deg rib angle of attack at a Reynolds number equal to 10,000.

Single-phase fluid flow and heat transfer characteristics of nanofluid in a circular microchannel: Development of flow and heat transfer correlations

2020 ◽  
Vol 234 (18) ◽  
pp. 3689-3708 ◽  
Author(s):  
Mangal Singh Lodhi ◽  
Tanuja Sheorey ◽  
Goutam Dutta
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Reynolds Number ◽  
Fluid Flow ◽  
Friction Factor ◽  
Nanoparticle Concentration ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer ◽  
Circular Microchannel

The convective heat transfer in microchannels with the use of nanofluids has proved to be a potential candidate for cooling of micro-electromechanical system devices. The current research article presents the experimental study on fluid flow and heat transfer characteristics of [Formula: see text]/water nanofluid in a microchannel under thermally developing laminar flow at Reynolds number ranging from 300 to 1000. The experimental set-up of a circular microchannel test section with an inner diameter of [Formula: see text] and length of [Formula: see text] is fabricated to conduct the experimental study. The effect of nanoparticle concentration ([Formula: see text]), Reynolds number ([Formula: see text]) on fluid flow and heat transfer characteristics of [Formula: see text]/water nanofluid have been measured and compared with that of distilled water (DW). The results indicate that the maximum enhancement in local heat transfer coefficient is achieved up to [Formula: see text], while friction factor is achieved up to [Formula: see text] for [Formula: see text]/water nanofluid with nanoparticle concentration of [Formula: see text] as compared to DW. The results showed that the performance evaluation criterion of [Formula: see text]/water nanofluid is greater than unity ([Formula: see text]), implying the benefits of nanofluids as compared to DW. Moreover, the predicted data obtained by the present proposed correlations for friction factor and local Nusselt number using [Formula: see text]/water nanofluid show reasonably good agreement with the deviations of [Formula: see text] and [Formula: see text], respectively, with the numerical data as compared to the predicted data obtained by the existing correlations available in the literature.

scholarly journals Heat transfer and flow region characteristics study in a non-annular channel between rotor and stator

2012 ◽  
Vol 16 (2) ◽  
pp. 593-603 ◽  
Author(s):  
M. Nili-Ahmadabadi ◽  
H. Karrabi
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Flow Characteristics ◽  
Annular Channel ◽  
Flow Region ◽  
Air Gap ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer ◽  
Slip Ring

This paper will present the results of the experimental investigation of heat transfer in a non-annular channel between rotor and stator similar to a real generator. Numerous experiments and numerical studies have examined flow and heat transfer characteristics of a fluid in an annulus with a rotating inner cylinder. In the current study, turbulent flow region and heat transfer characteristics have been studied in the air gap between the rotor and stator of a generator. The test rig has been built in a way which shows a very good agreement with the geometry of a real generator. The boundary condition supplies a non-homogenous heat flux through the passing air channel. The experimental devices and data acquisition method are carefully described in the paper. Surface-mounted thermocouples are located on the both stator and rotor surfaces and one slip ring transfers the collected temperature from rotor to the instrument display. The rotational speed of rotor is fixed at three under: 300rpm, 900 rpm and 1500 rpm. Based on these speeds and hydraulic diameter of the air gap, the Reynolds number has been considered in the range: 4000<Rez<30000. Heat transfer and pressure drop coefficients are deduced from the obtained data based on a theoretical investigation and are expressed as a formula containing effective Reynolds number. To confirm the results, a comparison is presented with Gazley?s (1985) data report. The presented method and established correlations can be applied to other electric machines having similar heat flow characteristics.

Sign in / Sign up

Export Citation Format

Share Document