Tensile Properties in Fe-Si Steel in a Low Temperature Range

AbstractHelium effect on loss of uniform elongation after low-temperature neutron irradiation of the V-Ti-Cr-Si-Al-Y alloy was studied. Helium implantation to about 30 atomic ppm was carried out before neutron irradiation to 50 dpa at 406°C. The yield stress of the irradiated specimen with helium pre-implantation was slightly smaller than that of irradiated specimens without helium. The uniform elongation and the increase in yield stress of the irradiated specimens were not affected by helium pre-implantation at ambient temperature. It might be possible that the helium effect appears after lower temperature irradiation such as 300°C or lower, which corresponds to the temperature range where the loss of uniform elongation of the alloy is particularly pronounced.

Download Full-text

BISMUTH-28.5Pb-14.5Sn-9Sb

Alloy Digest ◽

10.31399/asm.ad.bi0030 ◽

1983 ◽

Vol 32 (3) ◽

Keyword(s):

Low Temperature ◽

Physical Properties ◽

Tensile Properties ◽

Melting Temperature ◽

Eutectic Alloy ◽

Sheet Steel ◽

Heat Treating ◽

Temperature Range ◽

Silicon Sheet

Abstract Bismuth-28.5Pb-14.5Sn-9Sb is a bismuth-base non-eutectic alloy that melts over the low-temperature range of 218-440 F. Its controlled-shrinkage characteristics and low melting temperature make it a valuable industrial tool. It was developed and used originally for making punching dies to produce transformer laminations from silicon sheet steel. Now its many uses include filling blow holes in castings, anchoring dies and non-machinery parts, fixtures, jigs and hold-down bolts in concrete floors. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on casting, heat treating, and machining. Filing Code: Bi-30. Producer or source: Producers of low-melting alloys.

Download Full-text

INDALLOY 281-338

Alloy Digest ◽

10.31399/asm.ad.sn0010 ◽

1980 ◽

Vol 29 (9) ◽

Keyword(s):

Low Temperature ◽

Physical Properties ◽

Tensile Properties ◽

Eutectic Alloy ◽

Investment Casting ◽

Base Alloy ◽

Heat Treating ◽

Jet Engine ◽

Temperature Range ◽

Scientists And Engineers

Abstract INDALLOY 281-338 is a tin-base alloy that can be melted easily. It is non-eutectic alloy and melts through a temperature range of 281-338 F. It provides scientists and engineers with an easily castable material that is ready for use soon after it freezes; in addition, it can be recovered readily and recycled into new uses any number of times. Among its many uses are fusible mandrels for electroforming, proof casting in foundries, low-temperature solder, holding jet engine blades for machining and dies for wax patterns for investment casting. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on casting, heat treating, and machining. Filing Code: Sn-10. Producer or source: Indium Corporation of America.

Download Full-text

INDALLOY 147

Alloy Digest ◽

10.31399/asm.ad.bi0031 ◽

1983 ◽

Vol 32 (6) ◽

Keyword(s):

Low Temperature ◽

Physical Properties ◽

Tensile Properties ◽

Heat Treating ◽

Eutectic Structure ◽

Temperature Range

Abstract INDALLOY 147 is a bismuth-base controlled-shrinkage alloy with a non-eutectic structure. It melts over the narrow, low-temperature range of 142-149 F (61-65 C). Indalloy 147 provides engineers and technicians with an easily castable material that is ready for use as soon as it freezes. It is highly suitable in industry for such uses as anchoring parts for machining and support for bending tubing and extrusions. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on casting, heat treating, and machining. Filing Code: Bi-31. Producer or source: Indium Corporation of America.

Download Full-text

TIN BISMUTH 60-40

Alloy Digest ◽

10.31399/asm.ad.sn0012 ◽

1982 ◽

Vol 31 (11) ◽

Keyword(s):

Low Temperature ◽

Physical Properties ◽

Tensile Properties ◽

Eutectic Alloy ◽

Base Alloy ◽

Heat Treating ◽

Temperature Range

Abstract Tin-Bismuth 60-40 is a tin-base alloy that can be melted easily. It is a non-eutectic alloy and melts through the temperature range 281-338 F (138-170 C). It provides scientists, engineers and technicians with an easily castable material that is ready for use soon after it freezes; in addition, it can be recovered readily an recycled into new uses any number of times. Among its many uses are fusible mandrels for electroforming, low-temperature solder, holding parts for machining, dies for a wax patterns for investments casting and liquid scals for furnaces. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on casting, heat treating, machining, and joining. Filing Code: Sn-12. Producer or source: Low-melting alloy producers.

Download Full-text

BELMONT ALLOY 2405

Alloy Digest ◽

10.31399/asm.ad.sn0007 ◽

1979 ◽

Vol 28 (3) ◽

Keyword(s):

Low Temperature ◽

Physical Properties ◽

Tensile Properties ◽

Base Alloy ◽

Heat Treating ◽

Temperature Range ◽

Wax Pattern ◽

Temperature Work

Abstract BELMONT ALLOY 2405 is a tin-base alloy that can be melted easily. Being non-eutectic it melts through a temperature range, namely 281 to 338 F. It is used widely for proof casting in foundries, for sealing and soldering in low-temperature work, and for lost-wax pattern dies. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on heat treating and machining. Filing Code: Sn-7. Producer or source: Belmont Metals Inc..

Download Full-text

CERROMATRIX Alloy

Alloy Digest ◽

10.31399/asm.ad.bi0004 ◽

1978 ◽

Vol 27 (4) ◽

Keyword(s):

Low Temperature ◽

Physical Properties ◽

Tensile Properties ◽

Melting Temperature ◽

Eutectic Alloy ◽

Heat Treating ◽

Temperature Range ◽

Metal Products

Abstract CERROMATRIX Alloy is a bismuth-base non-eutectic alloy that melts over the low temperature range of 218-440 F. Its low melting temperature and controlled-shrinkage characteristics make it a valuable tool of industry for such operations as anchoring punches in dies, repairing broken dies and filling blow holes in castings. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on casting, heat treating, and machining. Filing Code: Bi-4. Producer or source: Cerro Metal Products.

Download Full-text

EVANOHM

Alloy Digest ◽

10.31399/asm.ad.ni0057 ◽

1960 ◽

Vol 9 (4) ◽

Keyword(s):

Electrical Resistivity ◽

Low Temperature ◽

Physical Properties ◽

Tensile Properties ◽

Temperature Coefficient ◽

Base Alloy ◽

Nickel Base Alloy ◽

Temperature Coefficient Of Resistance ◽

High Electrical Resistivity ◽

Nickel Base

Abstract EVANOHM is a nickel-base alloy having low temperature coefficient of resistance and high electrical resistivity. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on joining. Filing Code: Ni-57. Producer or source: Wilbur B. Driver Company.

Download Full-text

ISO-ELASTIC

Alloy Digest ◽

10.31399/asm.ad.fe0014 ◽

1957 ◽

Vol 6 (8) ◽

Keyword(s):

Corrosion Resistance ◽

Low Temperature ◽

Physical Properties ◽

Tensile Properties ◽

Temperature Coefficient ◽

Nickel Alloy ◽

Modulus Of Elasticity ◽

Heat Treating ◽

Precision Instrument ◽

Iron Nickel

Abstract ISO-ELASTIC is an iron-nickel alloy having low temperature coefficient of the modulus of elasticity. It is suitable for precision instrument springs. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, and machining. Filing Code: Fe-14. Producer or source: John Chatillon & Sons.

Download Full-text

INVAR M93

Alloy Digest ◽

10.31399/asm.ad.fe0143 ◽

2008 ◽

Vol 57 (1) ◽

Keyword(s):

Fracture Toughness ◽

Low Temperature ◽

Physical Properties ◽

Tensile Properties ◽

Low Temperatures ◽

Bend Strength ◽

Temperature Performance ◽

Ni Content ◽

Precision Alloys ◽

Ni Alloy

Abstract Invar is an Fe-Ni alloy with 36% Ni content that exhibits the lowest expansion of known metals from very low temperatures up to approximately 230 deg C (445 deg F). Invar M93 is a cryogenic Invar with improved weldability. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear and bend strength as well as fracture toughness and fatigue. It also includes information on low temperature performance as well as forming and joining. Filing Code: FE-143. Producer or source: Metalimphy Precision Alloys.

Download Full-text