scholarly journals Sodium Ferrite/Carbon Dioxide Reactivity for High Temperature Thermochemical Energy Storage

2019 ◽  
Vol 59 (4) ◽  
pp. 715-720 ◽  
Author(s):  
Hiroki Takasu ◽  
Hitoshi Hoshino ◽  
Yoshiro Tamura ◽  
Seon Tae Kim ◽  
Yukitaka Kato
2020 ◽  
Author(s):  
Hester E. Dijkstra ◽  
Cjestmir V. de Boer ◽  
Mariëlle Koenen ◽  
Jasper Griffioen

<p>High temperature - aquifer thermal energy storage (HT-ATES) is gaining momentum as sustainable option for the (seasonal) storage of heat, where geothermal heat may be one of the sources. To maximize the impact of geothermal systems, the heat produced in the summertime, which is not directly needed, can be temporarily stored in a groundwater aquifer for use in the winter. However, HT-ATES does not come without technical complications. One potential complication is carbonate scaling of the technical installation and/or the aquifer in the vicinity of the injection well. Precipitation of carbonates may occur when carbonate-saturated groundwater becomes heated, upon which the groundwater becomes increasingly supersaturated for carbonates. As part of the GEOTHERMICA project HEATSTORE, both a sampling method and an experimental set-up were developed. This experimental procedure enables the sampling and testing of groundwater from HT-ATES sites or else to determine the likelihood of calcium carbonate scaling in a HT-ATES system and, if so, identify the nature and extent.</p><p>For the HEATSTORE project, Groundwater was sampled at a HT-ATES test well drilled in Middenmeer, the Netherlands down to 370 meter depth. The sampling was done with a double walled vessel, which made it possible to maintain pressure on the water sample to prevent degassing of natural occurring dissolved gases like methane and carbon dioxide during sampling and storage, as well as preventing atmospheric contamination of the groundwater. The experiments were performed in two stainless steel autoclaves which were kept at 85 degrees Celsius for up to 5 days. Three types of experiments were performed to mimic the different components of the HT-ATES system: addition of a plate of stainless steel, addition of calcium carbonate crystals and addition of aquifer sediment. The first experiment did not show any carbonate precipitation, although geochemical modelling suggests oversaturation of calcite for the applied conditions. Calcite precipitation and recrystallization were observed only in the experiments with calcite crystal seeds added. The experiment with the aquifer sediment added to the reaction vessel, containing shell fractions and intact shells (e.g. Foraminifera), did not show calcite precipitation, neither showed the chemical analysis of the water at the end of the experiment a reduction in calcium concentration. Isotope analysis suggests that carbon dioxide was released by thermally enhanced degradation of sedimentary organic matter, which would have lowered the supersaturation of calcite.</p><p>These results suggest that aquifers, in which calcite is already present and limited (or no reactive) organic matter is available, could face a risk of scaling and subsequent injectivity/productivity issues when HT-ATES is applied in these aquifers. A proper water treatment, such as the addition of carbon dioxide or hydrochloric acid to the groundwater abstracted prior to heating, could be required to prevent groundwater from getting supersaturated with carbonate minerals.</p>


2021 ◽  
Vol 11 (13) ◽  
pp. 6234
Author(s):  
Ciprian Neagoe ◽  
Ioan Albert Tudor ◽  
Cristina Florentina Ciobota ◽  
Cristian Bogdanescu ◽  
Paul Stanciu ◽  
...  

Microencapsulation of sodium nitrate (NaNO3) as phase change material for high temperature thermal energy storage aims to reduce costs related to metal corrosion in storage tanks. The goal of this work was to test in a prototype thermal energy storage tank (16.7 L internal volume) the thermal properties of NaNO3 microencapsulated in zinc oxide shells, and estimate the potential of NaNO3–ZnO microcapsules for thermal storage applications. A fast and scalable microencapsulation procedure was developed, a flow calorimetry method was adapted, and a template document created to perform tank thermal transfer simulation by the finite element method (FEM) was set in Microsoft Excel. Differential scanning calorimetry (DSC) and transient plane source (TPS) methods were used to measure, in small samples, the temperature dependency of melting/solidification heat, specific heat, and thermal conductivity of the NaNO3–ZnO microcapsules. Scanning electron microscopy (SEM) and chemical analysis demonstrated the stability of microcapsules over multiple tank charge–discharge cycles. The energy stored as latent heat is available for a temperature interval from 303 to 285 °C, corresponding to onset–offset for NaNO3 solidification. Charge–self-discharge experiments on the pilot tank showed that the amount of thermal energy stored in this interval largely corresponds to the NaNO3 content of the microcapsules; the high temperature energy density of microcapsules is estimated in the range from 145 to 179 MJ/m3. Comparison between real tank experiments and FEM simulations demonstrated that DSC and TPS laboratory measurements on microcapsule thermal properties may reliably be used to design applications for thermal energy storage.


Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4379
Author(s):  
Max Hesselbrandt ◽  
Mikael Erlström ◽  
Daniel Sopher ◽  
Jose Acuna

Assessing the optimal placement and design of a large-scale high temperature energy storage system in crystalline bedrock is a challenging task. This study applies and evaluates various methods and strategies for pre-site investigation for a potential high temperature borehole thermal energy storage (HT-BTES) system at Linköping in Sweden. The storage is required to shift approximately 70 GWh of excess heat generated from a waste incineration plant during the summer to the winter season. Ideally, the site for the HT-BTES system should be able to accommodate up to 1400 wells to 300 m depth. The presence of major fracture zones, high groundwater flow, anisotropic thermal properties, and thick Quaternary overburden are all factors that play an important role in the performance of an HT-BTES system. Inadequate input data to the modeling and design increases the risk of unsatisfactory performance, unwanted thermal impact on the surroundings, and suboptimal placement of the HT-BTES system, especially in a complex crystalline bedrock setting. Hence, it is crucial that the subsurface geological conditions and associated thermal properties are suitably characterized as part of pre-investigation work. In this study, we utilize a range of methods for pre-site investigation in the greater Distorp area, in the vicinity of Linköping. Ground geophysical methods, including magnetic and Very Low-Frequency (VLF) measurements, are collected across the study area together with outcrop observations and lab analysis on rock samples. Borehole investigations are conducted, including Thermal Response Test (TRT) and Distributed Thermal Response Test (DTRT) measurements, as well as geophysical wireline logging. Drone-based photogrammetry is also applied to characterize the fracture distribution and orientation in outcrops. In the case of the Distorp site, these methods have proven to give useful information to optimize the placement of the HT-BTES system and to inform design and modeling work. Furthermore, many of the methods applied in the study have proven to require only a fraction of the resources required to drill a single well, and hence, can be considered relatively efficient.


2021 ◽  
Author(s):  
Viktoriia Mishukova ◽  
Nicolas Boulanger ◽  
Artem Iakunkov ◽  
Szymon Sollami Delekta ◽  
Xiaodong Zhuang ◽  
...  

Many industry applications require electronic circuits and systems to operate at high temperature over 150 oC. Although planar microsupercapacitors (MSCs) have great potential for miniaturized on-chip integrated energy storage components,...


Sign in / Sign up

Export Citation Format

Share Document