The Power Performance Characteristics of an Electric Resistance Furnace Equipped with Pulse-Phase Voltage Control

Vestnik MEI ◽  
2020 ◽  
Vol 2 (2) ◽  
pp. 83-89
Author(s):  
Viktor P. Rubtsov ◽  
◽  
Roman R. Klyushin ◽  
Nikolay I. Kryukov ◽  
◽  
...  
Author(s):  
S. V. Banushkina ◽  
◽  
A. I. Turkin ◽  
A. I. Chepurov ◽  
◽  
...  

Clinopyroxenes (Cpx) are one of the main rock-forming minerals, but stoichiometry of their compositions was called into question. In particular, an idea of hypothetical calcium molecule Eskola (CaEs, Ca0,5AlSi2O6) existence was expressed. This minal has structure vacancy and silica excess. Numerous experimental investigations in CMAS-system (CaO-MgO-Al2O3-SiO2) have showed that the question of non-stoichiometric Cpx existence remains open. This paper presents the results of an experimental study of the diopside Di (CaMgSi2O6) – calcium molecule Eskola CaEs (Ca0,5AlSi2O6) cross-section in the CMAS-system. The experiments were carried out in the following pressure and temperature range: P=10-4 – 3,0 GPa; T=966 – 15250C. Experiments at atmospheric pressure (10-4 GPa) were performed on a vertical shaft electric resistance furnace; high-pressure ones were performed on a "piston-cylinder" type apparatus. Samples obtained were analyzed using electron microprobe (EMP), scanning electron microscope (SEM) and Raman spectrometer. Depending on the P-T conditions, the samples contain the following phases: anorthite An, garnet Grt, diopside Di, clinopyroxene Cpx, quartz Qtz (tridymite Tr – for experiments at atmospheric pressure), and glass L. The data array on the composition of clinopyroxenes crystallized in this cross-section with diopside in various associations is generalized and supplemented. Clinopyroxenes were found to form quaternary solid solutions of diopside Di (CaMgSi2O6) – enstatite En (Mg2Si2O6) – calcium molecule Tschermak CaTs (CaAl2SiO6) – calcium molecule Eskola CaEs (Ca0,5AlSi2O6). The CaTs and CaEs minals contents are positively correlated with the amount of aluminum in clinopyroxene, and this relationship is particularly pronounced for CaTs. It is confirmed that clinopyroxenes in this cross-section can contain an excess of silica at both atmospheric and high pressures. Apparently, the cation vacancy that exists in pyroxene structure can participate in ordering processes. As a result the pyroxenes of another structure (not diopside – C2/c-symmetry) can be crystallized from total compositions in the Di-CaEs cross-section. Additional research is needed to support this hypothesis. Besides, at present investigation it was not possible to establish an unambiguous relationship between the Cpx composition and P-T-parameters, since it is also associated with both the mixture initial composition and the mineral association. Further experiments are required to justify any geothermobarometric dependence.


Author(s):  
Juan Antonio Aguilar-Garib ◽  
Osvaldo Tijerina-García ◽  
Javier Garza-Guajardo

A comparison of microwave and conventional, in an electric resistance furnace, sintered layers of dielectric base barium titanate (BaTiO3) of the kind employed for multilayer ceramic capacitors (MLCC) was performed. Two kinds of samples were used for each processing method; the layers alone without electrodes, and the green MLCC with the layers and electrodes interdigitated. Samples were exposed to microwaves for 20 minutes and heated up to 1050°C and 1150°C for sintering in a crucible with graphite that acted as reduction agent and microwave susceptor. Conventional sintering was performed in the same arrangement but lasted 120 minutes since it was found that 20 minutes was not enough time to achieve sintering. Heating rate in both cases was 10 °C/min. It was observed that the layers without the electrodes achieve about the same densification for both processes, while in the case of the green MLCC’s the results were variable, ranging from sample that became dust, to cracked samples and some well sintered ones. At least in the microwave case, it is possible that the variability of the results is due to the importance of the location of the sample in the cavity that in turn affects the electric field pattern, especially because the presence of the  electrodes that can cause overheating around them.


2001 ◽  
Vol 2001.11 (0) ◽  
pp. 291-294
Author(s):  
Mitsuhiro Tada ◽  
Katsuhiro Iwasaki ◽  
Takuya Shinagawa ◽  
Keisuke Nakahara ◽  
Hidenobu Hiraoka ◽  
...  

2012 ◽  
Vol 12 (2) ◽  
pp. 135-138 ◽  
Author(s):  
J. Pezda

Heat Treatment of AlZn10Si7MgCu Alloy and its Effect on Change of Mechanical Properties The most important parameters which predetermine mechanical properties of a material in aspects of suitability for castings to machinery components are: tensile strength (Rm), elongation (A5, hardness (HB) and impact strength (KCV). Heat treatment of aluminum alloys is performed to increase mechanical properties of the alloys mainly. The paper comprises a testing work concerning effect of heat treatment process consisting of solution heat treatment and natural ageing on mechanical properties and structure of AlZn10Si7MgCu alloy moulded in metal moulds. Investigated alloy was melted in an electric resistance furnace. Run of crystallization was presented with use of thermal-derivative method (ATD). This method was also implemented to determination of heat treatment temperature ranges of the alloy. Performed investigations have enabled determination of heat treatment parameters' range, which conditions suitable mechanical properties of the investigated alloy. Further investigations will be connected with determination of optimal parameters of T6 heat treatment of the investigated alloy and their effect on change of structure and mechanical/technological properties of the investigated alloy.


Sign in / Sign up

Export Citation Format

Share Document