scholarly journals Moulding of carbon fiber reinforced polycarbonate (CF/PC) using UD tape

2012 ◽  
Author(s):  
M. Shinohara ◽  
S. Isshiki ◽  
Y. Fukushima ◽  
T. Katayama ◽  
K. Tanaka
Keyword(s):  
Carbon Fiber ◽  
Fiber Reinforced ◽  
Carbon Fiber Reinforced

Effects of high pressure on the crystallization of carbon fiber reinforced polyetheretherketone (CF/PEEK) laminate composites

1990 ◽  
Vol 48 (4) ◽  
pp. 876-877
Author(s):  
Hong-Ming Lin ◽  
C. H. Liu ◽  
R. F. Lee
Keyword(s):  
High Pressure ◽  
Carbon Fiber ◽  
Sample Surface ◽  
High Yield ◽  
Fiber Reinforced ◽  
Laminate Composites ◽  
Peek Composite ◽  
Continuous Carbon Fiber ◽  
Carbon Fiber Reinforced

Polyetheretherketone (PEEK) is a crystallizable thermoplastic used as composite matrix materials in application which requires high yield stress, high toughness, long term high temperature service, and resistance to solvent and radiation. There have been several reports on the crystallization behavior of neat PEEK and of CF/PEEK composite. Other reports discussed the effects of crystallization on the mechanical properties of PEEK and CF/PEEK composites. However, these reports were all concerned with the crystallization or melting processes at or close to atmospheric pressure. Thus, the effects of high pressure on the crystallization of CF/PEEK will be examined in this study.The continuous carbon fiber reinforced PEEK (CF/PEEK) laminate composite with 68 wt.% of fibers was obtained from Imperial Chemical Industry (ICI). For the high pressure experiments, HIP was used to keep these samples under 1000, 1500 or 2000 atm. Then the samples were slowly cooled from 420 °C to 60 °C in the cooling rate about 1 - 2 degree per minute to induce high pressure crystallization. After the high pressure treatment, the samples were scanned in regular DSC to study the crystallinity and the melting temperature. Following the regular polishing, etching, and gold coating of the sample surface, the scanning electron microscope (SEM) was used to image the microstructure of the crystals. Also the samples about 25mmx5mmx3mm were prepared for the 3-point bending tests.

New unibody clamp anchors for post-tensioning carbon-fiber-reinforced polymer rods

PCI Journal ◽  
2014 ◽  
Vol 59 (1) ◽  
pp. 103-113 ◽  
Author(s):  
Clayton A. Burningham ◽  
Chris P. Pantelides ◽  
Lawrence D. Reaveley
Keyword(s):  
Carbon Fiber ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Reinforced Polymer ◽  
Carbon Fiber Reinforced ◽  
Post Tensioning ◽  
Polymer Rods

Restoring Initially Cracked Reinforced Concrete Beams utilizing Carbon Fiber Reinforced Polymer Strips

2019 ◽  
Vol 7 (1) ◽  
pp. 30-34
Author(s):  
A. Ajwad ◽  
U. Ilyas ◽  
N. Khadim ◽  
Abdullah ◽  
M.U. Rashid ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Concrete Beams ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Loading Test ◽  
Control Beam ◽  
Reinforced Polymer ◽  
Cfrp Sheet ◽  
Carbon Fiber Reinforced

Carbon fiber reinforced polymer (CFRP) strips are widely used all over the globe as a repair and strengthening material for concrete elements. This paper looks at comparison of numerous methods to rehabilitate concrete beams with the use of CFRP sheet strips. This research work consists of 4 under-reinforced, properly cured RCC beams under two point loading test. One beam was loaded till failure, which was considered the control beam for comparison. Other 3 beams were load till the appearance of initial crack, which normally occurred at third-quarters of failure load and then repaired with different ratios and design of CFRP sheet strips. Afterwards, the repaired beams were loaded again till failure and the results were compared with control beam. Deflections and ultimate load were noted for all concrete beams. It was found out the use of CFRP sheet strips did increase the maximum load bearing capacity of cracked beams, although their behavior was more brittle as compared with control beam.

Basic Design of High-Speed Riverine Craft Made of Carbon Fiber Reinforced Polymer

2020 ◽  
Vol 57 (4) ◽  
pp. 241-253
Author(s):  
Zhiqiang Han ◽  
Jung-kyu Choi ◽  
Inhyuck Hwang ◽  
Jinyoung Kim ◽  
Daekyun Oh
Keyword(s):  
Carbon Fiber ◽  
High Speed ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Basic Design ◽  
Fiber Reinforced ◽  
Reinforced Polymer ◽  
Carbon Fiber Reinforced

High thermal conductivity carbon fiber reinforced polymer based on a carbon fiber from pitch and dispersed-filled ENPB matrix

2018 ◽  
pp. 130-137
Author(s):  
E. A. Nikolaeva ◽  
A. N. Timofeev ◽  
K. V. Mikhaylovskiy
Keyword(s):  
Thermal Conductivity ◽  
Carbon Fiber ◽  
High Thermal Conductivity ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Carbon Powder ◽  
Fiber Reinforced ◽  
Thermophysical Characteristics ◽  
Reinforced Polymer ◽  
Carbon Fiber Reinforced

This article describes the results of the development of a high thermal conductivity carbon fiber reinforced polymer based on carbon fiber from pitch and an ENPB matrix modified with a carbon powder of high thermal conductivity. Data of the technological scheme of production and the results of determining the physicomechanical and thermophysical characteristics of carbon fiber reinforced polymer are presented. 

Sign in / Sign up

Export Citation Format

Share Document