3D seismic data reverse-time migration in Songzhan survey in North Songliao Basin

2014 ◽  
Author(s):  
Weihong Wang ◽  
Ying Shi
Keyword(s):  
Seismic Data ◽  
Songliao Basin ◽  
3D Seismic ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
Time Migration ◽  
3D Seismic Data

Near-Borehole Imaging Using Full-Waveform Sonic Data

2021 ◽  
Author(s):  
Hala Alqatari ◽  
Thierry-Laurent Tonellot ◽  
Mohammed Mubarak
Keyword(s):  
Seismic Data ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
Full Waveform ◽  
Time Migration ◽  
Imaging Results ◽  
High Resolution Images ◽  
Recorded Data ◽  
The Impact ◽  
Processing Steps

Abstract This work presents a full waveform sonic (FWS) dataset processing to generate high-resolution images of the near-borehole area. The dataset was acquired in a nearly horizontal well over a distance of 5400 feet. Multiple formation boundaries can be identified on the final image and tracked at up to 200 feet deep, along the wellbore's trajectory. We first present a new preprocessing sequence to prepare the sonic data for imaging. This sequence leverages denoising algorithms used in conventional surface seismic data processing to remove unwanted components of the recorded data that could harm the imaging results. We then apply a reverse time migration algorithm to the data at different processing stages to assess the impact of the main processing steps on the final image.

Some Aspects of Seismic Data Reverse Time Migration for Salt Tectonics Geology of the Dnieper-Donets Basin

2021 ◽  
Author(s):  
Pavlo Kuzmenko ◽  
Viktor Buhrii ◽  
Carlo D'Aguanno ◽  
Viktor Maliar ◽  
Hrigorii Kashuba ◽  
...  
Keyword(s):  
Seismic Data ◽  
Full Range ◽  
Donets Basin ◽  
Salt Tectonics ◽  
Imaging Method ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
Time Migration ◽  
Seismic Image ◽  
Complex Geology

Abstract Processing of the seismic data acquired in areas of complex geology of the Dnieper-Donets basin, characterized by the salt tectonics, requires special attention to the salt dome interpretation. For this purpose, Kirchhoff Depth Imaging and Reverse Time Migration (RTM) were applied and compared. This is the first such experience in the Dnieper-Donets basin. According to international experience, RTM is the most accurate seismic imaging method for steep and vertical geological (acoustic contrast) boundaries. Application of the RTM on 3D WAZ land data is a great challenge in Dnieper-Donets Basin because of the poor quality of the data with a low signal-to-noise ratio and irregular spatial sampling due to seismic acquisition gaps and missing traces. The RTM algorithm requires data, organized to native positions of seismic shots. For KPSDM we used regularized data after 5D interpolation. This affects the result for near salt reflection. The analysis of KPSDM and RTM results for the two areas revealed the same features. RTM seismic data looked more smoothed, but for steeply dipping reflections, lateral continuity of reflections was much improved. The upper part (1000 m) of the RTM has shadow zones caused by low fold. Other differences between Kirchhoff data and RTM are in the spectral content, as the former is characterized by the full range of seismic frequency spectrum. Conversely, beneath the salt, the RTM has reflections with steep dips which are not observed on the KPSDM. It is possible to identify new prospects using the RTM seismic image. Reverse Time Migration of 3D seismic data has shown geologically consistent results and has the potential to identify undiscovered hydrocarbon traps and to improve salt flank delineation in the complex geology of the Dnieper-Donets Basin's salt domes.

scholarly journals 3D Seismic Imaging through Reverse-Time Migration on Homogeneous and Heterogeneous Multi-Core Processors

2009 ◽  
Vol 17 (1-2) ◽  
pp. 185-198 ◽  
Author(s):  
Mauricio Araya-Polo ◽  
Félix Rubio ◽  
Raúl de la Cruz ◽  
Mauricio Hanzich ◽  
José María Cela ◽  
...  
Keyword(s):  
Oil And Gas ◽  
State Of The Art ◽  
Memory Bandwidth ◽  
3D Seismic ◽  
Computational Power ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
Time Migration ◽  
Computational Kernel ◽  
Oil And Gas Companies

Reverse-Time Migration (RTM) is a state-of-the-art technique in seismic acoustic imaging, because of the quality and integrity of the images it provides. Oil and gas companies trust RTM with crucial decisions on multi-million-dollar drilling investments. But RTM requires vastly more computational power than its predecessor techniques, and this has somewhat hindered its practical success. On the other hand, despite multi-core architectures promise to deliver unprecedented computational power, little attention has been devoted to mapping efficiently RTM to multi-cores. In this paper, we present a mapping of the RTM computational kernel to the IBM Cell/B.E. processor that reaches close-to-optimal performance. The kernel proves to be memory-bound and it achieves a 98% utilization of the peak memory bandwidth. Our Cell/B.E. implementation outperforms a traditional processor (PowerPC 970MP) in terms of performance (with an 15.0× speedup) and energy-efficiency (with a 10.0× increase in the GFlops/W delivered). Also, it is the fastest RTM implementation available to the best of our knowledge. These results increase the practical usability of RTM. Also, the RTM-Cell/B.E. combination proves to be a strong competitor in the seismic arena.

scholarly journals Imaging Complex Subsurface Structures for Geothermal Exploration at Pirouette Mountain and Eleven-Mile Canyon in Nevada

2021 ◽  
Vol 9 ◽  
Author(s):  
Yunsong Huang ◽  
Miao Zhang ◽  
Kai Gao ◽  
Andrew Sabin ◽  
Lianjie Huang
Keyword(s):  
High Resolution ◽  
Least Squares ◽  
Seismic Data ◽  
Seismic Wave Propagation ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
Geothermal Exploration ◽  
Subsurface Structures ◽  
Time Migration ◽  
Ground Roll

Accurate imaging of subsurface complex structures with faults is crucial for geothermal exploration because faults are generally the primary conduit of hydrothermal flow. It is very challenging to image geothermal exploration areas because of complex geologic structures with various faults and noisy surface seismic data with strong and coherent ground-roll noise. In addition, fracture zones and most geologic formations behave as anisotropic media for seismic-wave propagation. Properly suppressing ground-roll noise and accounting for subsurface anisotropic properties are essential for high-resolution imaging of subsurface structures and faults for geothermal exploration. We develop a novel wavenumber-adaptive bandpass filter to suppress the ground-roll noise without affecting useful seismic signals. This filter adaptively exploits both characteristics of the lower frequency and the smaller velocity of the ground-roll noise than those of the signals. Consequently, this filter can effectively differentiate the ground-roll noise from the signal. We use our novel filter to attenuate the ground-roll noise in seismic data along five survey lines acquired by the U.S. Navy Geothermal Program Office at Pirouette Mountain and Eleven-Mile Canyon in Nevada, United States. We then apply our novel anisotropic least-squares reverse-time migration algorithm to the resulting data for imaging subsurface structures at the Pirouette Mountain and Eleven-Mile Canyon geothermal exploration areas. The migration method employs an efficient implicit wavefield-separation scheme to reduce image artifacts and improve the image quality. Our results demonstrate that our wavenumber-adaptive bandpass filtering method successfully suppresses the strong and coherent ground-roll noise in the land seismic data, and our anisotropic least-squares reverse-time migration produces high-resolution subsurface images of Pirouette Mountain and Eleven-Mile Canyon, facilitating accurate fault interpretation for geothermal exploration.

Data- and model-domain up/down wave separation for reverse-time migration with free-surface multiples

2020 ◽  
Vol 223 (1) ◽  
pp. 77-93
Author(s):  
Peng Guo ◽  
Huimin Guan ◽  
George A McMechan
Keyword(s):  
Wave Equation ◽  
Free Surface ◽  
Seismic Data ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
Wave Separation ◽  
Time Migration ◽  
Model Domain ◽  
Image Artefacts ◽  
Recorded Data

SUMMARY Seismic data recorded using a marine acquisition geometry contain both upgoing reflections from subsurface structures and downgoing ghost waves reflected back from the free surface. In addition to the ambiguity of propagation directions in the data, using the two-way wave equation for wavefield extrapolation of seismic imaging generates backscattered/turned waves when there are strong velocity contrasts/gradients in the model, which further increases the wavefield complexity. For reverse-time migration (RTM) of free-surface multiples, apart from unwanted crosstalk between inconsistent orders of reflections, image artefacts can also be formed along with the true reflector images from the overlapping of up/downgoing waves in the data and in the extrapolated wavefield. We present a wave-equation-based, hybrid (data- and model-domain) wave separation workflow, with vector seismic data containing pressure- and vertical-component particle velocity from dual-sensor seismic acquisition, for removing image artefacts produced by the mixture of up/downgoing waves. For imaging with free-surface multiples, the wavefield extrapolated from downgoing ghost events (reflected from the free surface) in the recorded data act as an effective source wavefield for one-order-higher free-surface multiples. Therefore, only the downgoing waves in the data should be used as the source wavefield for RTM with multiples; the recorded upgoing waves in the seismograms will be used for extrapolation of the time-reversed receiver wavefield. We use finite-difference (FD) injection for up/down separation in the data domain, to extrapolate the down- and upgoing waves of the common-source gathers for source and receiver wavefield propagation, respectively. The model-domain separation decomposes the extrapolated wavefield into upgoing (backscattered) and downgoing (transmitted) components at each subsurface grid location, to remove false images produced by cross-correlating backscattered waves along unphysical paths. We combine FD injection with the model-domain wavefield separation, for separating the wavefield into up- and downgoing components for the recorded data and for the extrapolated wavefields. Numerical examples using a simple model, and the Sigsbee 2B model, demonstrate that the hybrid up/down separation approach can effectively produce seismic images of free-surface multiples with better resolution and fewer artefacts.

Sign in / Sign up

Export Citation Format

Share Document