Predictions for the Heat Transfer and Boundary Layer Growth in the Radiatively Driven Hypersonic Wind Tunnel and Comparisons with Experiment at Ultra High Reynolds Number (Invited)

2002 ◽  
Author(s):  
Garry Brown ◽  
Ihab Girgis ◽  
Richard Miles
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Reynolds Number ◽  
Wind Tunnel ◽  
High Reynolds Number ◽  
Layer Growth ◽  
Hypersonic Wind Tunnel ◽  
High Reynolds ◽  
Boundary Layer Growth

Characterization of the Custom-Designed, High Reynolds Number Water Tunnel

2016 ◽  
Author(s):  
Yasaman Farsiani ◽  
Brian R. Elbing
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Test Section ◽  
High Reynolds Number ◽  
Layer Growth ◽  
Water Tunnel ◽  
Freestream Velocity ◽  
Section Design ◽  
High Reynolds

This paper reports on the characterization of the custom-designed high-Reynolds number recirculating water tunnel located at Oklahoma State University. The characterization includes the verification of the test section design, pump calibration and the velocity distribution within the test section. This includes an assessment of the boundary layer growth within the test section. The tunnel was designed to achieve a downstream distance based Reynolds number of 10 million, provide optical access for flow visualization and minimize inlet flow non-uniformity. The test section is 1 m long with 15.2 cm (6-inch) square cross section and acrylic walls to allow direct line of sight at the tunnel walls. The verification of the test section design was accomplished by comparing the flow quality at different location downstream of the flow inlet. The pump was calibrated with the freestream velocity with three pump frequencies and velocity profiles were measured at defined locations for three pump speeds. Boundary layer thicknesses were measured from velocity profile results and compared with analytical calculations. These measurements were also compared against the facility design calculations.

A Numerical Investigation Into the Heat Transfer Performance and Particle Dynamics of a Compressible, Highly Mass Loaded, High Reynolds Number, Particle Laden Flow

2021 ◽  
Author(s):  
Kyle Hassan ◽  
Robert F. Kunz ◽  
David Hanson ◽  
Michael Manahan
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Computational Model ◽  
High Reynolds Number ◽  
Heat Transfer Performance ◽  
Particle Dynamics ◽  
Transfer Performance ◽  
Temperature Distributions ◽  
High Reynolds ◽  
Particle Laden Flow

Abstract In this work, we study the heat transfer performance and particle dynamics of a highly mass loaded, compressible, particle-laden flow in a horizontally-oriented pipe using an Eulerian-Eulerian (two-fluid) computational model. An attendant experimental configuration [1] provides the basis for the study. Specifically, a 17 bar co-flow of nitrogen gas and copper powder are modeled with inlet Reynolds numbers of 3×104, 4.5×104, and 6×104 and mass loadings of 0, 0.5, and 1.0. Eight binned particle sizes were modeled to represent the known powder properties. Significant settling of all particle groups are observed leading to asymmetric temperature distributions. Wall and core flow temperature distributions are observed to agree well with measurements. In high Reynolds number cases, the predictions of the multiphase computational model were satisfactorily aligned with the experimental results. Low Reynolds number model predictions were not as consistent with the experimental measurements.

Row Removal Heat Transfer Study for Pin Fin Arrays

2014 ◽  
Author(s):  
Kathryn L. Kirsch ◽  
Jason K. Ostanek ◽  
Karen A. Thole ◽  
Eleanor Kaufman
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
High Reynolds Number ◽  
Pin Fin ◽  
Heat Transfer Augmentation ◽  
Aspect Ratios ◽  
Pin Fins ◽  
High Reynolds ◽  
Pin Fin Arrays ◽  
Transfer Study

Arrays of variably-spaced pin fins are used as a conventional means to conduct and convect heat from internal turbine surfaces. The most common pin shape for this purpose is a circular cylinder. Literature has shown that beyond the first few rows of pin fins, the heat transfer augmentation in the array levels off and slightly decreases. This paper provides experimental results from two studies seeking to understand the effects of gaps in pin spacing (row removals) and alternative pin geometries placed in these gaps. The alternative pin geometries included large cylindrical pins and oblong pins with different aspect ratios. Results from the row removal study at high Reynolds number showed that when rows four through eight were removed, the flow returned to a fully-developed channel flow in the gap between pin rows. When larger alternative geometries replaced the fourth row, heat transfer increased further downstream into the array.

scholarly journals Wall-attached structures of velocity fluctuations in a turbulent boundary layer

2018 ◽  
Vol 856 ◽  
pp. 958-983 ◽  
Author(s):  
Jinyul Hwang ◽  
Hyung Jin Sung
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
High Reynolds Number ◽  
Wall Turbulence ◽  
Velocity Fluctuations ◽  
Moderate Reynolds Number ◽  
Wide Range ◽  
Logarithmic Region ◽  
High Reynolds ◽  
Attached Eddies

Wall turbulence is a ubiquitous phenomenon in nature and engineering applications, yet predicting such turbulence is difficult due to its complexity. High-Reynolds-number turbulence arises in most practical flows, and is particularly complicated because of its wide range of scales. Although the attached-eddy hypothesis postulated by Townsend can be used to predict turbulence intensities and serves as a unified theory for the asymptotic behaviours of turbulence, the presence of coherent structures that contribute to the logarithmic behaviours has not been observed in instantaneous flow fields. Here, we demonstrate the logarithmic region of the turbulence intensity by identifying wall-attached structures of the velocity fluctuations ($u_{i}$) through the direct numerical simulation of a moderate-Reynolds-number boundary layer ($Re_{\unicode[STIX]{x1D70F}}\approx 1000$). The wall-attached structures are self-similar with respect to their heights ($l_{y}$), and in particular the population density of the streamwise component ($u$) scales inversely with $l_{y}$, reminiscent of the hierarchy of attached eddies. The turbulence intensities contained within the wall-parallel components ($u$ and $w$) exhibit the logarithmic behaviour. The tall attached structures ($l_{y}^{+}>100$) of $u$ are composed of multiple uniform momentum zones (UMZs) with long streamwise extents, whereas those of the cross-stream components ($v$ and $w$) are relatively short with a comparable width, suggesting the presence of tall vortical structures associated with multiple UMZs. The magnitude of the near-wall peak observed in the streamwise turbulent intensity increases with increasing $l_{y}$, reflecting the nested hierarchies of the attached $u$ structures. These findings suggest that the identified structures are prime candidates for Townsend’s attached-eddy hypothesis and that they can serve as cornerstones for understanding the multiscale phenomena of high-Reynolds-number boundary layers.

Sign in / Sign up

Export Citation Format

Share Document