scholarly journals Fire resistance of circulat steel tubes infilled with ultra-high strength concrete with external fire protection

2019 ◽  
Vol 39 (1) ◽  
pp. 71-80
Author(s):  
Xiao Lyu ◽  
Erfeng Du ◽  
Ran Li
Keyword(s):  
Finite Element ◽  
High Strength Concrete ◽  
Three Dimensional ◽  
High Strength ◽  
Element Model ◽  
Test Results ◽  
Element Analysis ◽  
Strength Concrete ◽  
Tubular Columns ◽  
Axially Loaded

In this paper, a non-linear three-dimensional finite element model is presented in order to study the behaviour of axially loaded ultra-high strength concrete filled circular hollow tubular columns exposed to fire. Ultra-high strength concrete with compressive strength greater than 180 N/mm2 has been developed for concrete filled tubes for use in high–rise buildings. This paper studies the structural performance of fire protected ultra-high strength concrete filled tubular columns exposed to the standard ISO fire. The aim of this work is to understand and represent the behaviour of axially loaded ultra-high strength concrete filled circular hollow tubular columns in fire situations and to compare calculation results with experiment. The numerical analyses are carried out using a general finite element analysis package ABAQUS and the results are validated against the test results in terms of heat distribution and mechanical behavior. Comparison with the test results showed a reasonable agreement with finite element results in terms of temperature prediction and load displacement behavior during the fire.

Seismic behaviour of prestressed high-strength concrete piles under combined axial compression and cyclic horizontal loads

2018 ◽  
Vol 22 (5) ◽  
pp. 1089-1105 ◽  
Author(s):  
Xizhi Zhang ◽  
Sixin Niu ◽  
Jia-Bao Yan ◽  
Shaohua Zhang
Keyword(s):  
Finite Element ◽  
Axial Compression ◽  
High Strength Concrete ◽  
High Strength ◽  
Element Model ◽  
Test Results ◽  
Seismic Behaviour ◽  
Strength Concrete ◽  
Concrete Piles ◽  
Concrete Pile

In order to simulate the seismic behaviour of the prestressed high-strength concrete piles under working state, six full-scale prestressed high-strength concrete piles were tested under combined axial compression and cyclic horizontal loads. Different axial compression levels and prestressing levels of prestressed tendons were studied in this test programme. The failure mode, bending resistance, displacement ductility, stiffness degradation and energy dissipation of the prestressed high-strength concrete piles under different loading scenarios were measured and analysed. Test results indicated that the axial compression ratio and prestressing level of prestressed tendon significantly influenced the seismic performance of prestressed high-strength concrete piles. Theoretical models were developed to predict cracking, yielding and ultimate bending resistances of the prestressed high-strength concrete pile under combined compression and bending. Finite element model was also developed to simulate the ultimate strength behaviour of the prestressed high-strength concrete pile under combined compression and flexural bending. The accuracies of the theoretical and finite element model were checked through validations of their predictions against the reported test results.

scholarly journals Numerical Investigation of Stress Block for High Strength Concrete Columns

2020 ◽  
Vol 6 (5) ◽  
pp. 974-996
Author(s):  
Nizar Assi ◽  
Husain Al-Gahtani ◽  
Mohammed A. Al-Osta
Keyword(s):  
Finite Element ◽  
Intensity Factor ◽  
Finite Element Model ◽  
High Strength Concrete ◽  
Analytical Approach ◽  
High Strength ◽  
Element Model ◽  
Strength Concrete ◽  
Stress Block ◽  
The Finite Element Model

This paper is intended to investigate the stress block for high strength concrete (HSC) using the finite element model (FEM) and analytical approach. New stress block parameters were proposed for HSC including the stress intensity factor (α1) and the depth factor (β1) based on basic equilibrium equations. A (3D) finite element modeling was developed for the columns made of HSC using the comprehensive code ABAQUS. The proposed stress parameters were validated against the experimental data found in the literature and FEM. Thereafter, the proposed stress block for HSC was used to generate interaction diagrams of rectangular and circular columns subjected to compression and uniaxial bending. The effects of the stress block parameters of HSC on the interaction diagrams were demonstrated. The results showed that a good agreement is obtained between the failure loads using the finite element model and the analytical approach using the proposed parameters, as well as the achievement of a close agreement with experimental observation. It is concluded that the use of proposed parameters resulted in a more conservative estimation of the failure load of columns. The effect of the stress depth factor is considered to be minor compared with the effect of the intensity factor.

scholarly journals Simplified 2D Finite Element Model for Calculation of the Bearing Capacity of Eccentrically Compressed Concrete-Filled Steel Tubular Columns

2021 ◽  
Vol 11 (24) ◽  
pp. 11645
Author(s):  
Anton Chepurnenko ◽  
Batyr Yazyev ◽  
Besarion Meskhi ◽  
Alexey Beskopylny ◽  
Kazbek Khashkhozhev ◽  
...  
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Cross Sections ◽  
Three Dimensional ◽  
Element Model ◽  
Longitudinal Force ◽  
Effective Area ◽  
Element Analysis ◽  
Tubular Columns ◽  
Cfst Columns

Concrete-filled steel tubular (CFST) columns are widely used in construction due to effective resistance to compression and bending joint action. However, currently, there is no generally accepted effective calculation method considering both nonlinearities of the materials and lateral compression. The article proposes the finite element analysis method of concrete-filled steel tubular columns in a physically nonlinear formulation by reducing a three-dimensional problem to a two-dimensional one based on the hypothesis of plane sections. The equations of Geniev’s concrete theory of plasticity are used as relations establishing the relationship between stresses and strains. The technique was tested by comparing the solution with the calculation in a three-dimensional formulation in the LIRA-SAPR software package and with the experimental data of A.L. Krishan and A.I. Sagadatov. It has been established that the effective area of operation of circular-section columns are small eccentricities of the longitudinal force. The proposed approach can be applied to analyzing the stress–strain state and bearing capacity of pipe-concrete columns of arbitrary cross-sections. There are no restrictions on the composition of concrete, and the shell material can be steel and fiberglass.

Sign in / Sign up

Export Citation Format

Share Document