Seismic behaviour of prestressed high-strength concrete piles under combined axial compression and cyclic horizontal loads

2018 ◽  
Vol 22 (5) ◽  
pp. 1089-1105 ◽  
Author(s):  
Xizhi Zhang ◽  
Sixin Niu ◽  
Jia-Bao Yan ◽  
Shaohua Zhang
Keyword(s):  
Finite Element ◽  
Axial Compression ◽  
High Strength Concrete ◽  
High Strength ◽  
Element Model ◽  
Test Results ◽  
Seismic Behaviour ◽  
Strength Concrete ◽  
Concrete Piles ◽  
Concrete Pile

In order to simulate the seismic behaviour of the prestressed high-strength concrete piles under working state, six full-scale prestressed high-strength concrete piles were tested under combined axial compression and cyclic horizontal loads. Different axial compression levels and prestressing levels of prestressed tendons were studied in this test programme. The failure mode, bending resistance, displacement ductility, stiffness degradation and energy dissipation of the prestressed high-strength concrete piles under different loading scenarios were measured and analysed. Test results indicated that the axial compression ratio and prestressing level of prestressed tendon significantly influenced the seismic performance of prestressed high-strength concrete piles. Theoretical models were developed to predict cracking, yielding and ultimate bending resistances of the prestressed high-strength concrete pile under combined compression and bending. Finite element model was also developed to simulate the ultimate strength behaviour of the prestressed high-strength concrete pile under combined compression and flexural bending. The accuracies of the theoretical and finite element model were checked through validations of their predictions against the reported test results.

scholarly journals Fire resistance of circulat steel tubes infilled with ultra-high strength concrete with external fire protection

2019 ◽  
Vol 39 (1) ◽  
pp. 71-80
Author(s):  
Xiao Lyu ◽  
Erfeng Du ◽  
Ran Li
Keyword(s):  
Finite Element ◽  
High Strength Concrete ◽  
Three Dimensional ◽  
High Strength ◽  
Element Model ◽  
Test Results ◽  
Element Analysis ◽  
Strength Concrete ◽  
Tubular Columns ◽  
Axially Loaded

In this paper, a non-linear three-dimensional finite element model is presented in order to study the behaviour of axially loaded ultra-high strength concrete filled circular hollow tubular columns exposed to fire. Ultra-high strength concrete with compressive strength greater than 180 N/mm2 has been developed for concrete filled tubes for use in high–rise buildings. This paper studies the structural performance of fire protected ultra-high strength concrete filled tubular columns exposed to the standard ISO fire. The aim of this work is to understand and represent the behaviour of axially loaded ultra-high strength concrete filled circular hollow tubular columns in fire situations and to compare calculation results with experiment. The numerical analyses are carried out using a general finite element analysis package ABAQUS and the results are validated against the test results in terms of heat distribution and mechanical behavior. Comparison with the test results showed a reasonable agreement with finite element results in terms of temperature prediction and load displacement behavior during the fire.

Seismic behavior of normal-strength concrete-filled precast high-strength concrete centrifugal tube columns

2019 ◽  
Vol 23 (4) ◽  
pp. 614-629
Author(s):  
Shaohua Zhang ◽  
Xizhi Zhang ◽  
Shengbo Xu ◽  
Xingqian Li
Keyword(s):  
Axial Compression ◽  
High Strength Concrete ◽  
Seismic Behavior ◽  
Failure Modes ◽  
Concrete Strength ◽  
High Strength ◽  
Test Results ◽  
Normal Strength Concrete ◽  
Strength Concrete ◽  
Normal Strength

This study reports the cyclic loading test results of normal-strength concrete-filled precast high-strength concrete centrifugal tube columns. Seven half-scale column specimens were tested under cyclic loads and axial compression loads to investigate their seismic behavior. The major parameters considered in the test included axial compression ratio, filled concrete strength, and volumetric stirrup ratio. The structural behavior of each specimen was investigated in terms of failure modes, hysteresis behavior, bearing capacity, dissipated energy, ductility, stiffness degradation, drift capacity, and strain profiles. Test results revealed that the concrete-filled precast high-strength concrete centrifugal tube column exhibited good integral behavior, and the failure modes of all columns were ductile flexural failures. Lower axial compression ratio and higher volumetric stirrup ratio resulted in more satisfactory ductile performance. In contrast, the filled concrete strength has a limited influence on the structural behavior of concrete-filled precast high-strength concrete centrifugal tube columns. Based on the limit analysis method, the calculation formula for the bending capacity of the concrete-filled precast high-strength concrete centrifugal tube column was developed, and the results predicted from the formulas were in good agreement with the experiment results.

scholarly journals Numerical Investigation of Stress Block for High Strength Concrete Columns

2020 ◽  
Vol 6 (5) ◽  
pp. 974-996
Author(s):  
Nizar Assi ◽  
Husain Al-Gahtani ◽  
Mohammed A. Al-Osta
Keyword(s):  
Finite Element ◽  
Intensity Factor ◽  
Finite Element Model ◽  
High Strength Concrete ◽  
Analytical Approach ◽  
High Strength ◽  
Element Model ◽  
Strength Concrete ◽  
Stress Block ◽  
The Finite Element Model

This paper is intended to investigate the stress block for high strength concrete (HSC) using the finite element model (FEM) and analytical approach. New stress block parameters were proposed for HSC including the stress intensity factor (α1) and the depth factor (β1) based on basic equilibrium equations. A (3D) finite element modeling was developed for the columns made of HSC using the comprehensive code ABAQUS. The proposed stress parameters were validated against the experimental data found in the literature and FEM. Thereafter, the proposed stress block for HSC was used to generate interaction diagrams of rectangular and circular columns subjected to compression and uniaxial bending. The effects of the stress block parameters of HSC on the interaction diagrams were demonstrated. The results showed that a good agreement is obtained between the failure loads using the finite element model and the analytical approach using the proposed parameters, as well as the achievement of a close agreement with experimental observation. It is concluded that the use of proposed parameters resulted in a more conservative estimation of the failure load of columns. The effect of the stress depth factor is considered to be minor compared with the effect of the intensity factor.

scholarly journals Structural Behavior of High-Strength Concrete Slabs Reinforced with GFRP Bars

Polymers ◽  
2021 ◽  
Vol 13 (17) ◽  
pp. 2997
Author(s):  
Maher A. Adam ◽  
Abeer M. Erfan ◽  
Fatma A. Habib ◽  
Taha A. El-Sayed
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
High Strength Concrete ◽  
High Strength ◽  
Element Model ◽  
Experimental Results ◽  
Structural Behavior ◽  
Concrete Slabs ◽  
Strength Concrete ◽  
Gfrp Bars

In this manuscript, structural testing was conducted on high-strength concrete slab specimens to investigate the behavior of such specimens when reinforced with a locally produced GFRP reinforcement. Subsequently, a finite element model (FEM) was constructed and validated against the experimental results. In the experimental phase, a total of eleven specimens (nine were reinforced with GFRP, while two were reinforced with conventional steel) were constructed and tested. The slabs dimensions are 700 mm × 1750 mm with variable thickness from 100 mm to 150 mm and different reinforcement ratios using different diameters. The structural behavior of the tested slabs was investigated in terms of ultimate load, ultimate deflection, load–deflection relationship, and crack pattern. Additionally, a nonlinear finite element model using the software ANSYS 2019-R1 was constructed to simulate the structural behavior of slabs reinforced with GFRP bars. The results obtained from the finite element analysis are compared with experimental results. The outcomes showed that the contribution of GFRP rebars in concrete slabs improved slab ductility and exhibited higher deflection when compared with traditional steel rebars. Good agreement between experimental and nonlinear analysis was obtained.

Effects of Nano-CaCO3 on the Compressive Strength and Microstructure of High Strength Concrete in Different Curing Temperature

2011 ◽  
Vol 121-126 ◽  
pp. 126-131 ◽  
Author(s):  
Qing Lei Xu ◽  
Tao Meng ◽  
Miao Zhou Huang
Keyword(s):  
Compressive Strength ◽  
Low Temperature ◽  
High Strength Concrete ◽  
High Strength ◽  
Curing Temperature ◽  
Test Results ◽  
Strength Concrete ◽  
Calcium Nitrite ◽  
Orientation Index ◽  
Early Strength

In this paper, effects of nano-CaCO3 on compressive strength and Microstructure of high strength concrete in standard curing temperature(21±1°C) and low curing temperature(6.5±1°C) was studied. In order to improve the early strength of the concrete in low temperature, the early strength agent calcium nitrite was added into. Test results indicated that 0.5% dosage of nano-CaCO3 could inhibit the effect of calcium nitrite as early strength agent, but 1% and 2% dosage of nano-CaCO3 could improve the strength of the concrete by 13% and 18% in standard curing temperature and by 17% and 14% in low curing temperature at the age of 3days. According to the XRD spectrum, with the dosage up to 1% to 2%, nano-CaCO3 can change the orientation index significantly, leading to the improvement of strength of concrete both in standard curing temperature and low curing temperature.

Effect of Chopped Basalt Fiber on the Fresh and Hardened Properties of Fly Ash High Strength Concrete

2014 ◽  
Vol 567 ◽  
pp. 381-386 ◽  
Author(s):  
Nasir Shafiq ◽  
Muhd Fadhil Nuruddin ◽  
Ali Elheber Ahmed Elshekh ◽  
Ahmed Fathi Mohamed Salih
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
High Strength Concrete ◽  
Basalt Fiber ◽  
High Strength ◽  
Progressive Increase ◽  
Test Results ◽  
Strength Concrete ◽  
Hardened Properties ◽  
Chopped Basalt Fiber

In order to improve the mechanical properties of high strength concrete, HSC, several studies have been conducted using fly ash, FA. Researchers have made it possible to achieve 100-150MPa high strength concrete. Despite the popularity of this FAHSC, there is a major shortcoming in that it becomes more brittle, resulting in less than 0.1% tensile strain. The main objective of this work was to evaluate the fresh and hardened properties of FAHSC utilizing chopped basalt fiber stands, CBFS, as an internal strengthening addition material. This was achieved through a series of experimental works using a 20% replacement of cement by FA together with various contents of CBFS. Test results of concrete mixes in the fresh state showed no segregation, homogeneousness during the mixing period and workability ranging from 60 to 110 mm. Early and long terms of compressive strength did not show any improvement by using CBFS; in fact, it decreased. This was partially substituted by the effect of FA. Whereas, the split and flexural strengths of FASHC were significantly improved with increasing the content of CBFS as well as the percentage of the split and flexural tensile strength to the compressive strength. Also, test results showed a progressive increase in the areas under the stress-strain curves of the FAHSC strains after the CBFS addition. Therefore, the brittleness and toughness of the FAHSC were enhanced and the pattern of failure moved from brittle failure to ductile collapse using CBFS. It can be considered that the CBFS is a suitable strengthening material to produce ductile FAHSC.

Sign in / Sign up

Export Citation Format

Share Document